Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

ADVERTISE HERE - FREE TRIAL

Adivice needed about cracks

Posts

Adivice needed about cracks

#1

Adivice needed about cracks

Thomas Skaggs, Foothills of Mount Level

>Hello all. Attached is a (sorry) lousy picture of a bowl I am working on. It is obviously not finished yet, and yes I need to sand out that dark rub. I am getting ready to put sone of my flat work in a gallery show in April. The gallery owner said she wouldn't mind having a piece or two of something I turned for the gallery.

Lord knows I am not much of a turner but I thought "what the heck".

This bowl has some hairline cracks. They are closed up and don't appear to be getting worse (I'll know if they do by April). Look closely at the edge facing you and you can see them. They cannot be felt but they can be detected by close inspection.

What is the conventional wisdom about this? Do such flaws render a piece unsuitable for a gallery? What do you folks do?

Thanks

Tommy


img

Re: Adivice needed about cracks

#2

Re: Adivice needed about cracks

Ed in No.VA

>Flaws in flatwork can be beautymarks in turning. Knots, bark, wildgrain, and yes even cracks can add to the interest of a piece. Wood is an organic substance it moves and has cracks. If someone has to have a perfect piece send them to walmart to buy plastic.

just my rant on flaws

Ed

Re: Adivice needed about cracks

#3

Re: Adivice needed about cracks

Jake (SoMN)

>I am a beginning turner, so take my advice with a grain of salt. I am sure some of the more experienced folks will chime in.

I have had good luck mixing of CA and sawdust and filling the crack with it. This was done during the initial turning phase. (Just before final turning and sanding) I have also left bowls with cracks present as well. It all depends on your definition of "perfect" and weather the bowl is going to be for use or for show....

Although it looks as if this bowl is already way past the initial turning phases.

Good luck

Jake

(remove the 2 for email)

Re: Adivice needed about cracks

#4

Re: Adivice needed about cracks

Bart Rhoads

>One thing the pros will tell you is never try to hide a crack or blemish. Try to enhance it. There is several ways to do this. Mix a color with epoxy and fill the crack. I like to use carbon black or brass powder, expecially on my mesquite. Lots of folks use powdered turquoise. I dont particurally like the turquoise but that is my opinion. Also you can use aluminum powder. You can either buy the powder or make it. It has to be very fine to accomplish the solid brass or aluminum color look. For brass, you can use a belt sander up against a piece of brass pipe and then collect the brass after you sand enough. This works with aluminum also. I have heard that Rit cloth dies work also but I havent used that yet. There is others substances you can use also. After these are placed in the crack you can turn the item just like you normally would. Craft Supply also sells other types you can use. I am sure others will have other ideas but this is what I use mostly.

Re: Adivice needed about cracks

#5

Richard Allen

Re: Adivice needed about cracks

Richard Allen

>Hi Tommy

For the most part I will sell a bowl with a repaired crack such as you have pictured.

Since you are only going to put a few turned pieces in the show I would put in pieces without cracks. You won't be there to explain that the cracks are natural and that they have been repaired. Save the repaired cracked pieces for when you can talk with the person who is considering a purchase.

Good Luck

Re: Adivice needed about cracks

#6

Oops I forgot one thing

Bart Rhoads

>I forgot to mention that I mix these powders with Epoxy glue. I like to use the slow setting type. It gives you a longer working time and also I think it dries clearer than the fast type.

Re: Adivice needed about cracks

#7

Brad Vietje

Re: Adivice needed about cracks

Brad Vietje

>I agree. I usually don't sell cracked pieces unless the cracks add character, but I do sell cracked and repaired pieces with black line spalting -- the CA repairs usually look like more black lines.

BTW, because those cracks run across growth rings on end grain, the may be heat checks, which result from overheating the wood while sanding. Of course, they could have been in the wood before you even started to turn it, but that's one thing to look out for.

Its a nice bowl; if you find it doesn't sell (when you are there to discuss it), you could always consider scorching, texturing, or carving on the outside, metal leaf, or other techniques to mask the cracks and give it a whole new look.

Safe spinning,

Brad Vietje

Thetford, VT