Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Support WoodCentral when buying things you need

Two Platters (for Bill Grumbine)

Posts

Two Platters (for Bill Grumbine)

#1

Two Platters (for Bill Grumbine)

Ruth Niles

>These are 2 of 3 platters I turned from a piece of spalted maple that Mr. Bill Grumbine gave me. The board was a little less than 1" thick and 12" wide and these both are 11" - 11 1/2" diam. The one on the right has no finish just buffed with tripoli, that's it. The one on the left was rubbed with Danish oil then buffed with tripoli, white diamond and carnuba wax. Other than the darker tone, they both look and feel the same.

Thanks, Bill! : )


img

Re: Two Platters (for Bill Grumbine)

#2

Re: Two Platters (for Bill Grumbine)

Ron in Drums PA

>Nice Ruth

I think that might be ambrosia maple!

Re: Two Platters (for Bill Grumbine)

#3

Keith Tompkins

Re: Two Platters (for Bill Grumbine)

Keith Tompkins

>Hi Ruth! Nice work, did you turn these on the new General?

Re: Two Platters (for Bill Grumbine)

#4

Re: Two Platters (for Bill Grumbine)

Bill Grumbine, Kutztown PA

>Beatuiful Ruth! You did a great job with that board. Of course, I am going to have to be more careful about that stuff I give away! ;-)

Bill

Re: Two Platters (for Bill Grumbine)

#5

Very Nice!

Jennifer@Indy.USA

>Ruth,

Those are beautiful. I'm not sure if I've ever seen Ambrosia with that wide of streaks before? Simply lovely.

Jennifer

Re: Two Platters (for Bill Grumbine)

#6

Re: Two Platters (for Bill Grumbine)

Molly Winton

>Jennifer said it...Simply Lovely! I really like the details on these. I would imagine it was challenging getting the platter depth given the low clearance of only <1" stock. Nice job!

Re: Two Platters (for Bill Grumbine)

#7

Re: Two Platters (for Bill Grumbine)

Duane C.Leach

>Nice job... The one on the left with the danish oil finish has more of it's curly grain showing.Or am i seeing things.

Duane

Re: Two Platters (for Bill Grumbine)

#8

Re: Two Platters (for Bill Grumbine)

Ruth Niles

>Ron, you'd have to ask Bill about it being ambrosia. I do have some spalted maple with this type pattern, there was no red anywhere on the wood but that doesn't mean you may not be right.

Re: Two Platters (for Bill Grumbine)

#9

Re: Two Platters (for Bill Grumbine)

Ruth Niles

>Yes, Keith, these were done on the new General and with pleasure! This new machine really puts the old General to shame.

Re: Two Platters (for Bill Grumbine)

#10

Re: Two Platters (for Bill Grumbine)

Ruth Niles

>Duane, the grain on the one with the oil does appear more pronounced in the picture I think because the light is bouncing off the other (due to poor photography).

Re: Two Platters (for Bill Grumbine)

#11

Re: Two Platters (for Bill Grumbine)

Ruth Niles

>Thank you both, Jennifer and Molly (roommates for KC, right?). Jennifer, you will have a blast with Molly, just don't get the notion you will be taking my place on a regular basis! : )

only kidding, maybe we 3 could do a symposium next time.

Back to the platters. Molly, I use a face plate on what will be the top, finish the bottom with a 1/8" recess, chuck, turn the top then power sand the recess to more of a decorative groove than a sharp recess. I don't waste any wood.

Re: Two Platters (for Bill Grumbine)

#12

Re: Two Platters (for Bill Grumbine)

Barry Turner

>You have a "new" General?

Re: Two Platters (for Bill Grumbine)

#13

Re: Two Platters (for Bill Grumbine)

Dave Peebles Lyons, Ohio!

>Hello Ruth,

It is great to see you post here.

I hope all is well.

Those look great, it's good to have friends with wonderful wood. :) And a turner with the skills to make such beautiful work.

I guess I may be out of the loop, but what Lathe are you turning on now?

Best wishes,

Dave

Re: Two Platters (for Bill Grumbine)

#14

Re: Two Platters (for Bill Grumbine)

Jimbo13

>Yup, that's ambrosia maple - the staining results from bacteria left by the ambrosia beetle. The small holes are where the beetle passed through the tree.

Gidday,

Jim

Re: Two Platters (for Bill Grumbine)

#15

Brad Vietje

Atta go, Ruth -- Beauties !

Brad Vietje

>

Re: Two Platters (for Bill Grumbine)

#16

Re: Two Platters (for Bill Grumbine)

Mike Schwing from Md.

>I'm late to the party, but yes, very nice Ruth! My eye finds the one on the left more pleasing, the bead, which looks lovely, defines the interior very well. Keep it up!

Re: Two Platters (for Bill Grumbine)

#17

Re: Two Platters (for Bill Grumbine)

Bill Grumbine, Kutztown PA

>Hi Ron and Ruth (And everyone else)

Yes, this is ambrosia maple, as we turners name it. In flat form at the sawmill, it is referred to as wormy maple, and I use it frequently in furniture that I build. Most often it is found in red maple trees. I can often find it with both the worm streak and curl in it.

At last year's Five Barns picnic we sawed up a log of this stuff which I bought from my local sawmill. There was not a single curl in it, but it has some nice worm streaking, and as a bonus, it is filled with tiny burl clusters throughout. That wood is drying right now for use as furniture sometime next year.

Bill

Re: Two Platters (for Bill Grumbine)

#18

Keith Tompkins

Re: Two Platters (for Bill Grumbine)

Keith Tompkins

>Ruth, I can spot a turning done on a General instantly! LOL Did you ever try the detail gouge?

Yes , the VS General is a smooth running machine!

Re: Two Platters (for Bill Grumbine)

#19

Re: Two Platters (for Bill Grumbine)

Ruth Niles

>Yes, Keith, I got the detail gouge and now that I've learned how to use it like you showed me, I absolutely LOVE it. Thanks for the tip.

Re: Two Platters (for Bill Grumbine)

#20

Re: Two Platters (for Bill Grumbine)

Ruth Niles

>Hi Barry,

Yep, I have a brand spanking new 26020 electric VS GENERAL and I absolutely love it.