Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Premium Domestic, Figured & Live Edge Hardwoods in Stock. Best Prices for Serious Woodworkers.

Holly vase, knots, pith and all

Posts

Holly vase, knots, pith and all

#1

Holly vase, knots, pith and all

Dave Smith, Longview, WA

>I turned this vase from the trunk of a holly tree. Pith in the bottom and about 10 knots around the side. I almost turned through the side when finishing the inside. A dead limb didn�t survive the rough turning so there is a 3/16" hole about 1/3 of the way up the side.

Sides are 3/32" and less in some spots. The piece was rough turned to about 3/8" thickness then soaked in alcohol for 9 hours. Wrapped with paper and allowed to dry for several weeks. It was basically dry after 2 weeks as the piece only lost 0.15 ounces during the third week when I finished turned the top of the vase. It took a couple more weeks before I got around to turning off the tenon.

The vase is 8" tall and 3 1/8" wide at the base. The rim is 2 3/4" wide. All the knots and the pith remained in tack. Sanded to 600 on the lathe then hand sanded with the grain with 600. Finished with two coats of Rockler�s Gel Polyurethane. It weighs all of 4.35 ounces.



The missing limb looks like a black spot at the lower right.



Several knots that did not split and crack.



The pith is off set from center because I mounted the piece in the center of the trunk.



Top of the vase.

I need to get a longer hollowing tool or not make such tall vases.

Thanks for looking.

Dave Smith

Finally setup a photo booth in Longview, WA.

Re: Holly vase, knots, pith and all

#2

Re: Holly vase, knots, pith and all

Jennifer@Indy.USA

>Hi Dave,

Very Pretty....isn't Holly lovely to turn. I just love it! I think you are the reason I got hooked. The hunks of holly that you left me a couple of years ago.

Jen : )

Re: Holly vase, knots, pith and all

#3

Re: Holly vase, knots, pith and all

RonZ

>Very nice Dave. Holly is #2 on my favorite to turn list. Boxwood being #1 and ebony #3. Depending on the work, I prefer to have knots in holly as people think it's ivory or plastic.

Re: Holly vase, knots, pith and all

#4

Re: Holly vase, knots, pith and all

RevDoug

>Dave,

You have done a nice job here. Was a bit curious why you left the base so blocky rather than giving it a waist and foot? Or even justcurving into the foot? As it is, the piece seems a bit rooted to me.

I love the selection of wood and that the included pith is off center. My mind seems to work along the same line as your's on this matter.

Your sanding and finish look nice as well. Thanks for sharing this one with us.

Turn 'em round,

RevDoug

Re: Holly vase, knots, pith and all

#5

Re: Holly vase, knots, pith and all

Sharon in Topanga, CA

>Your comment about people thinking holly is plastic made me chuckle. The first piece of turned holly I saw I described to loml as looking just like plastic. It is nice to see some holly with character!

Re: Holly vase, knots, pith and all

#6

Would you believe I wanted it to look like that?

Dave Smith, Longview, WA

>Hi RevDoug,

When I rough turned the vase I had more wood that I could hollow. So I cut off the excess and made a new tenon. When I returned the piece to the lathe I trued the out side and made a cut with my parting tool to define the bottom. When I got to the bottom of the inside I discovered I had no material left to shape the base beyond what you see.

The wide base makes it more stable for holding a dried flower arrangement. Yeah, that's it. That is why I wanted it that shape. Works for me.

Dave Smith

Making it up as I go along in Longview, WA.

Re: Holly vase, knots, pith and all

#7

Its your story and you're sticking to it.

RevDoug

>I completely understand. It is funny how we get to turning and forget to get everything planned for. This piece will surely be a stable vase. Thanks again for sharing it with us. Makes me anxious to get some of my holly on the lathe.

Turn 'em round,

RevDoug