Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Nearly 100 Exotic Wood Species, Direct-Imported Since 1972. Shop Slabs & Turning Stock.

Jet 1442 variable pulley drive

Posts

Jet 1442 variable pulley drive

#1

Jet 1442 variable pulley drive

Lan Brady

>My speed adjustment has become very difficult to move. I removed the cover and lubricated both the motor shaft and the spidle shaft. I also lubricated the rack and pinion, but it has not helped. Any suggestions on what part of the puzzle I am missing? Any help is appreciated.

Thanks, Lan

Re: Jet 1442 variable pulley drive

#2

Re: Jet 1442 variable pulley drive

Joel Hunnicutt

>Lan, there have been a couple of post about this same problem. One of the causes seems to be the gook that them put on the lathe to keep it from rusting during shipping. I undertand that it can harden and cause the reeves pulley to not move properly. Maybe sombody that has cleaned theirs can chime in.

Re: Jet 1442 variable pulley drive

#3

Re: Jet 1442 variable pulley drive

Dennis Taylor (Akron, Ohio)

>I can be of help in this matter...I got a new 1442 lathe, and the lever got very, very hard to move...I contacted Woodcraft and they connected me to Jet direct..Jet had me do the following:

1. pull cover off motor and clean with lacquer thinner...I used brake cleaner...it cleans out the cosmoline from shipping..

2. spray with a silicon lube, all moving parts...

I did these to no avail, they sent me a new one, and it is the same thing..my shop isn't heated all the time, and I think any residue from the cosmoline gets cool and stiffens up,making it hard to change speeds..cleaning will help a lot but not liminate the problem...

I just talked with a Jet rep at a woodworking show, and he made it sound like it isn't possible to happen, but it does and is...trying clean it with the brake cleaner...Jet had me you lacquer thinner, and then denatured alchol, there last recommendation to me was to pull the pulleys off the shaft and then clean, but I didn't feel comforable doing that, maybe you could try it...cleaning will help...any ? email me...Dennis

p.s. I went on with this problem for about 2 months...

Re: Jet 1442 variable pulley drive

#4

Re: Jet 1442 variable pulley drive

John Lucas

>Just a thought. I use mineral spirits to clean off cosmoline. It penetrates well. Maybe that would work.

Re: Jet 1442 variable pulley drive

#5

Spring loaded ball bearing on the end of the shaft

Dave Smith, Longview, WA

>Hi Lan,

My Jet 1236 has the same problem. I have taken to squirting or forcing oil into the end of the shaft with a little metal oil can. I use drippings from when I add oil to my car so the lathe get Mobil 1 5w30. Anyway there is a hole under the movable pulley and oil will be slung into it when the lathe runs. If you have the cover off make sure you put something around the shaft or you will have oil on the wall, ceiling, yourself, etc. DAMHIKT When I ask Jet about the oil port they had no idea what it was for. I was trying to figure out what grease to use in it when Wally Dickerman told me it was an oil port. You learn things going to BBQ's.

Dave Smith

Shade tree mechanic in Longview, WA.

Re: Jet 1442 variable pulley drive

#6

Re: Spring loaded ball bearing on the end of the s

Ron in Drums PA

>I'd be careful about using oil on the shaft. Oil will hold wood dust which can be abrasive. Silicone would be much better to use.

Re: Jet 1442 variable pulley drive

#7

Re: Spring loaded ball bearing on the end of the s

Howard Norman

>Dave, are you putting the oile into the threaded spindle shaft, or am I missing something? I am talking about the Jet 1236 lathe.

Howard