Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Precision you can feel — woodworking perfected with Lee Valley

What is the bare minimum required to turn a bowl

Posts

What is the bare minimum required to turn a bowl

#1

What is the bare minimum required to turn a bowl

Jack Diemer

>I just recently acquired a Delta Midi from lowes. I am not really interested in turning pens, I want to go straight to bowls. What is the bare mimium I need to buy to turn a good bowl safely.

Re: What is the bare minimum required to turn a bowl

#2

Re: What is the bare minimum required to turn a bo

MP Wall

>You got a faceplate with that lathe didn't you? If so then just a 3/8 or 1/2 bowl gouge and you are in business. Rough between the spur and live center, form a flat surface on what will be the bottom of the bowl, glue to a waste block attached to the faceplate, let the glue set, return the outside of the bowl and then hollow. Mind you that is quick and dirty and refuses to mention sanding as I hate it, but seem to do a lot of it. You sand the outside when turned true and then sand when you get the inside to your liking.

Good luck with the new addiction,

MP Wall

Re: What is the bare minimum required to turn a bowl

#3

Richard Allen

Re: What is the bare minimum required to turn a bo

Richard Allen

>A big screwdriver that you sharpen over and over again is the bare minimum.

If you want to see what it like to turn a bowl safely then consider taking a bowl turning class.

Re: What is the bare minimum required to turn a bowl

#4

Membership in you're local club  *LINK*

Phil Joines in Krum, Texas

>


AAW chapters

Re: What is the bare minimum required to turn a bowl

#5

Re: What is the bare minimum required to turn a bo

Jack Diemer

>The lathe comes with at 3in faceplate, So I need some CA glue, a gouge, what about a scraper?, and what do I need to sand the bowl.

Re: What is the bare minimum required to turn a bowl

#6

Re: What is the bare minimum required to turn a bo

Ken Grunke

>Yes, Jack, you should have a round-nose scraper. Getting the inside of a bowl smooth with just a gouge takes some instruction and many, many, hours of practice.

You'll also need some way to cut the bowl blanks--a bandsaw, gas or electric chainsaw, sawzall, bowsaw, etc.

Re: What is the bare minimum required to turn a bowl

#7

Re: What is the bare minimum (addendum)

Ken Grunke

>Hopefully, you also have a spur drive center and tail center for rough-turning a bowl blank between centers.

Re: What is the bare minimum required to turn a bowl

#8

Re: What is the bare minimum (addendum) *LINK*

Jack Diemer

>I have a full woodworking shop, so the bandsaw is not a problem, I have all those tools you mentioned. However, I have not idea what a spur drive center and a tail center are. I am a newbie when it comes to this turning thing. I consider myself a tool collector, who makes things every once in a while.


My shop

Re: What is the bare minimum required to turn a bowl

#9

Re: What is the bare minimum (addendum)

Don Henthorn

>The lathe came with the spur center and tail center so you are in business. Of course as you progress you will see other things that you reallyn need. Then is the time to get them, not when you are first starting.

Re: What is the bare minimum required to turn a bowl

#10

Re: What is the bare minimum required to turn a bo

Bill Hale

>A couple of good thoughts and a couple of bad !

I agree the 3/8 and 1/2 bowl gouges. I also agree on getting some help and advise from an experienced turner. Join a club ! Watch videos and read books. But, No. 1, get some help with an experienced turner. It will speed your profencies, and make you a better and safer turner.

Post where you are and ask for help.

Good turning and be safe.

Bill