Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

WD-40 overspray on milk paint

Posts

WD-40 overspray on milk paint

#1

Jack Guzman from Maine

WD-40 overspray on milk paint

Jack Guzman from Maine

I was freeing up a rusty tool with WD-40 and got some splatter on a chair I built. This chair is coated with the first coat of milk paint,waiting on a second coat. I may have a problem with adhesion over the splatter. Will a wipe with mineral spirits remove the overspray enough so paint will stick?

Re: WD-40 overspray on milk paint

#2

I doubt it...

John in NM

I would suggest a rinse of either acetone or alcohol, but I have no experience in cleaning milk paint so its just a guess.

I suppose you could always sand the spots down to the bare wood and repaint - this is a several color job right? If so it wouldn't hurt a bit to have a patch in the base coat.

Re: WD-40 overspray on milk paint

#3

Re: WD-40 overspray on milk paint

Bill Tindall, E.Tn.

You will need to test to be sure. Make up a test piece and try mineral spirit wipe, sand lightly and recoat. I like naptha better because it would evaporate faster, and acetone less because it would evaporate too fast. If you are unlucky you will spread a tiny amount of WD 40 chemicals all over the area and have a worse mess to deal with, if the milk paint is particularly sensitive to traces of "oil".

WD 40 is oily and not volatile over a time scale relevant to this problem. Water is going to bead up on, or wick away from, an "oiled" surface. We know from spraying lacquer that a few molecules of silicone will fish eye lacquer. Can't predict how sensitive milk paint will be. This sensitivity will have to be determined by experiment.

Re: WD-40 overspray on milk paint

#4

Rafael from PA

Re: WD-40 overspray on milk paint

Rafael from PA

WD-40 eventually dries, but I don't know how long it takes. After a quick internet search it seems like it leaves an oily residue too.

You may have to strip your chair and start over.

A crazy thought is to seal the spill with something, maybe shellac, and apply another coat of your milk paint.

Re: WD-40 overspray on milk paint

#5

Jack Guzman from Maine

shellac

Jack Guzman from Maine

Actually ,I considered that.

Re: WD-40 overspray on milk paint

#6

Re: shellac

Oskar

Peter Galbert mentioned this, sealing the bottom color layer with a thin shellack layer toa avoid mixing it up with the top layer. I think it is described on his blog, have a look.

Re: WD-40 overspray on milk paint

#7

Think this through

Bill Tindall, E.Tn.

French polishing. Add mineral oil to rubber. Oil blooms to shellac surface as the shellac is rubbed on and dries.

Re: WD-40 overspray on milk paint

#8

that's my thought...

David Weaver

..if you have excessive oil of any amount with shellac, it will come to the surface and can then be wiped off. Shellac with following milk paint is a good idea. I've done it with chalk paints without issue over all kinds of surfaces. You almost can't have too much oil with a french polish process - if it doesn't come up to the surface, it's not a problem. If it comes to the surface, you can wipe it off until the surface is dry. Any oil I've tried so far as long as it's not a drying oil (applying shellac directly to a board wet with BLO wasn't an issue, but the BLO has to be wiped off or it'll start to dry on the surface and will become sticky).

Re: WD-40 overspray on milk paint

#9

Re: Think this through

John Aniano in central NJ

So Bill,

Is WD-40 the new miracle oil added to shellac for French polishing? :D

John

Re: WD-40 overspray on milk paint

#10

removing molecules

Bill Tindall, E.Tn.

Sure one can wipe the excess oil off the surface of the shellac. But one molecular layer of oil will result in the surface tension of the surface to be that of oil and not shellac.

As worrisome the stuff works different from the hydrocarbon solvent that is its main constituent. A surfactant is present that alters the surface tension of the metal which allows WD40 to spread across the metal surface and into crevices.

I am 100% confident I cannot predict the result and 100% confident as well that I can come up with the explanation for the result once I know it. :)

Re: WD-40 overspray on milk paint

#11

yes on the surface...

David Weaver

...about the only thing you can really do with the last coat of french polish is continue to buff the surface until there's almost nothing, and then fetch another dry cloth and burnish the surface with that. At least that's what I've done when I want "no oil".

I'm sure that if you could see all of the molecules, you could see some oil somewhere, but there hasn't been enough for me to have an adhesion issue.

But as you say, it doesn't mean the next person won't have an issue.

I can't remember exactly what WD40 is - you could look quickly and find out how volatile the parts are. I vaguely recall it being one part that won't persist that long and another part that will. I don't remember exactly what, just remember looking in the past when someone suggested it's unhealthy to touch that it was one part stuff that goes away and another one stuff that stays around.

Re: WD-40 overspray on milk paint

#12

OK, now I have to go look up...

David Weaver

..the msds again.

OK, I looked it up - it looks like 35% of it is some kind of oil similar to paraffin oil.

The rest, i know nothing about chemistry, but the terms used for it remind me of what would go in an all-fuel tractor in the 1930s.

Will do up a couple of pencils with it -french polish- with buttonlac, and report on the results. I can't imagine it wouldn't work (given so far that nothing that seems like an oil of any kind has failed for me.

Re: WD-40 overspray on milk paint

#13

A test

Bill Tindall, E.Tn.

Try something to remove. Add a drop of water to the cleaned area. If it wets it is clean enough. If it beads, still oil there.

Re: WD-40 overspray on milk paint

#14

And

Bill Tindall, E.Tn.

if the splatters are on an area that would be not too risky, heat with hair dryer and see if you can volatilize it away. The stuff is a mix of high boiling hydrocarbons Stoddard Solvent (more or less)and even higher boiling hydrocarbons approaching light oil. Heat might work....or crack the wood >(

Again I would test the approach on a test piece.

Re: WD-40 overspray on milk paint

#15

Re: shellac

Warren in Lancaster, PA

We are talking about a wash coat of shellac between paint coats, not French polish on mahogany. Shellac has good adherence on all surfaces and presents a good surface for your next coat. We use shellac over resinous knots to keep the pitch from bleeding into paint. Even if there were some sort of bloom, it could not make a big difference after another coat of paint. We can use shellac over an oil finish.

I would recommend rubbing the surface with a clean cloth to pick up oil residue. before doing a shellac or paint coat. Wd-40 is not a drying oil.

Re: WD-40 overspray on milk paint

#16

clarifying the point

Bill Tindall, E.Tn.

WD 40 is a mix of hydrocarbons with the volatility of kerosene and another hydrocarbon component less volatile, and a surfactant. A water based finish is not going to stick to a surface coated with this stuff. There could be an additional problem similar to that which we encounter when there is a trace of silicone on a surface and we spray it with lacquer.

If shellac covers the splaters of WD 40 that would be grand, presuming milk paint sticks to shellac. I don't know whether it does or not. If the shellac displaces the WD40 and it blooms to the shellac surface there was no benefit of applying the shellac. One is still faced with painting water on oil.

There is too much going on here to make a reliable prediction, which is why I recommended preparing a test panel and testing proposed solutions. All that could happen may, or may, not. The result will depend on how sensitive milk paint is to the surface properties of what it is applied to.

Re: WD-40 overspray on milk paint

#17

Re: clarifying the point

Warren in Lancaster, PA

It sounds as if you are long on theory, short on experience.

Re: WD-40 overspray on milk paint

#18

Re: clarifying the point

Bill Tindall, E.Tn.

I have tried every way possible to acknowledge that I have no experience painting milk paint over WD 40. But in case anyone missed this fact it was helpful to them for you to point it out.

I do have experience spraying lacquer and know first hand the problems that result from a mismatch of lacquer surface tension to that of the substrate. Milk Paint may be more or less picky about what it sits down on. I have no idea. I don't like milk paint and avoid using it. I find the acrylic replacements are easier to deal with and look the same for what I use them for.

Re: WD-40 overspray on milk paint

#19

Re: WD-40 overspray on milk paint

Mike in Zuni VA

Jack,

This is what is on the Old Fashion Milk Paint's Website:

Porous Surfaces: Milk paint, like all water paints, adheres best to a porous surface, such as bare wood or masonry.

Nonporous Surfaces: Our Extra-Bond additive will help the milk paint adhere to MOST clean, sound nonporous surfaces.

POROUS SURFACES PAINTING PROCEDURES

New wood or other porous surfaces such as masonry.

Note: No primer is necessary – the first coat acts as its own primer on most softwoods and open-grained hardwoods. However, close-grained hardwoods such as maple or birch will require an initial coat of milk paint with Extra-Bond added.

Clean: Wipe down the item with a damp rag to remove any dust and to pre-dampen the surface.

Seal: Then, seal knots, if any (optional) with shellac (apply first coat of milk paint while the shellac is still tacky) OR paint knots with a mixture of prepared milk paint with Extra-Bond added.

First Coat: Paint the entire item with a first coat of milk paint.

Second Coat: After an hour or more, if you wish, you can rub down the first coat lightly with a Scotch- brite pad, fine sandpaper, or non-oiled steel wool[NOTE WEL]. Now, if it looks like it needs it, you can apply a second coat of straight milk paint.

Finished: If you like the look and the rough texture, your masterpiece is finished!!

Optional: After a couple of hours, or overnight, you may wish to rub down to a satin-smooth finish and/or “distress” the finish. You can rub down the surface as in No. 4 above or do any type of distressing at this time. Be sure to try any of these techniques on a test piece to be sure you will like the end result.

Also under Non-Porous Surfaces:

Good finishing practice states that any surface to be painted or repainted must be cleaned and dulled, not shiny. All grime should be removed with a washing soda such as T.S.P. and shiny surfaces should be scuffed up with sandpaper. Surface must be clean, sound and free of oil, grease, dust and dirt.[AGAIN NOTE WELL] By ignoring this practice, the new paint may not adhere well and future coats could peel off when repainted.

Neutralize: On any surfaces that have been chemically stripped of finish, be sure to neutralize any residual chemicals by wiping the surface with a 50/50 vinegar and water solution prior to re-painting.

If it was mine, Sand spots in question to bare wood, use the 50/50 vinegar and water, and repaint the spots. Then do your second coat as planned.

When all else fails read the instructions.

Mike in Zuni A

Re: WD-40 overspray on milk paint

#20

acrylic replacements for milk paints

Jack Dover

Could you please recommend some, Bill? I like the looks, but real milk paint is kinda too much effort.

Thanks!

Re: WD-40 overspray on milk paint

#21

Re: acrylic replacements for milk paints

Bill Tindall, E.Tn.

General Finishes

The product used to be called Country Colors. It has been reformulated and renamed.....can not recall name but it is obvious from their product literature. Lots of "milk paint" colors.