Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Drawer fitting question

Posts

Re: Drawer fitting question

#26

Never encountered a stop before

Bill Tindall, E.Tn.

Indeed I did and asked a question in my 7/10 post. Now I understand the stop to be a permanently mounted sticky up square post for butting stuff against. Its large size relative to a "dog" provides more support. I never encountered this device before in a bench.

So, dogs are temporary sticky up things and a post a larger square post that is permanently fixed to some handy place on the bench?

Re: Drawer fitting question

#27

Re: Never encountered a stop before

Steve Voigt

Bill, I would say the difference is size rather than permanence. My 3 x3 stop is in a through mortise, so it can easily be knocked below the surface or out of the bench entirely. Same thing for a dog; the only differences are that the dog hole is 3/4" diameter rather than a large square mortise, and dog holes are normally in line with a matching dog hole in an end vise, for clamping purposes.

I should have mentioned that my vise is left handed, so reverse the placement for a righty.

Surprised you never encountered this type of stop before. Just google "roubo planing stop." Most hits will include the toothed metal piece, but it's optional. Or you can use the types shown by Dave, Derek, and Wiley--lots of great options. Bottom line is that planing against a stop is usually faster/more efficient than clamping between dogs because you don't have to clamp/unclamp every time you want to check or reposition the part.

Re: Drawer fitting question

#28

I'll experiment

Bill Tindall, E.Tn.

I have a multitasking bench that does farm repair and furniture. Knowing the concept I can work something out for it.

Historically with just a stop I have gotten rotation when planing against it. Maybe more horizontal surface area is a cure.

Re: Drawer fitting question

#29

Re: I'll experiment

John Aniano in central NJ

Bill,

Use a doe's foot or similar batten to prevent the stock from rotating. Look for the Schwartz book I mentioned. These are described and shown in detail...

John

Re: Drawer fitting question

#30

Re: I'll experiment

William Duffield

If you are planing the bottom of a drawer, or the top of a drawer before installing the drawer bottom, and if you have positioned the mortise in the bench closer to where you start planing the drawer (instead of at the end of the planing pass), and set the planing stop inside the drawer, then there will be less tendency for the drawer to rotate. You can adjust the height of the planing stop so it is just lower than the drawer height. Pay attention to the grain direction of the planing stop, to minimize wood movement along the length of the bench, so it doesn't just drop through in the winter or get jammed tight in the summer. If you have a German or Eastern European stye bench with a complicated tail vise, you can hold the planing stop in the tail vise instead of precisely fitting a mortise for it, or you could clamp it in your shoulder vise and plane across the end of the bench, if the drawers are short enough.

Re: Drawer fitting question

#31

I have been to the mountaintop...

Jim Matthews

I've seen Derek Cohen's impeccable furniture in person.

I own a set of Brian Boggs' ladderback chairs.

The difference is akin to parallel parking at Walmart and landing on The Moon.

Re: Drawer fitting question

#32

Re: I'll experiment

Bill Tindall, E.Tn.

A set of drawers often means drawers of all the same width, varying only in height. The two part capture you describe should prove to be a rapid means of fitting.

Best of course is to not need to do height fitting. I fit the sides as a pair before I dovetail them. And usually that is all that is necessary. But occasionally something happens where a few extra shavings of height need to be removed.

Re: Drawer fitting question

#33

Re: Stop question - holding things on the bench... *LINK*

David Bassett

Some of that information is also in Christopher Schwarz's latest workbench book which is available as a free download.

I'll add the link to the blog announcement. You can get the download link from the product page in their store (or from my next post.)


‘The Anarchist’s Workbench.’ For Free. Forever.

Re: Drawer fitting question

#35

Re: Never encountered a stop before

AZ in Colorado Springs

The height of the planing stop is adjustable, where bench dogs that I've seen are 1/2" or so tall. When preparing the edges of your drawer stock, for example, with a hand plane, you can raise the planing stop to just a bit less than the stock, butt the stock against the planing stop, and dress away. The taller planing stop will prevent the work piece from tipping forward as you plane it.

That's the real difference (and utility) of the planing stop for me.

Re: Drawer fitting question

#36

My bench dogs are height adjustable

Bill Houghton, Sebastopol, CA

I use the Lee Valley round dogs, which can adjust up to about 3/4" in height.

Re: Drawer fitting question

#37

End stop

Bill Houghton, Sebastopol, CA

This idea is not original with me - I can't recall where I first saw it. It's a piece of plywood (I used fairly high grade plywood), attached to the end of the workbench in the direction I plane. I used hanger bolts and knurled nuts to hold it in place. This is the stop down, out of the way, when I don't need it:



and this is the stop up, for use:



I can adjust height to fit the thickness of the stock being planed, and, whether the stock is narrow or wide, I don't get rotation.

Re: Drawer fitting question

#38

Re: End stop

Darrell LaRue

Just like mine, except I used wing nuts (it's what I had on hand). I think your knurled nuts would be better as they are less likely to catch on things.