Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Spoon carving

Posts

Spoon carving

#1

Spoon carving

Paul in NJ

My last post generated a question or two about my spoon carving. I cut a branch of cherry the other day to show how I carve my spoons. The branch is small, only 1-1/2” in diameter, so it limits the size of the spoons I made.

There is a lot of cherry that grows in this area and is my favorite for green wood carving of spoons. I have used other fruitwoods like apple and pear as well as birch, soft maple, and other fine-grained diffuse porous woods but cherry is the easiest to find so I mostly use that. A fresh cut branch of 3-4 inches is ideal. I carve the spoon bowl from the outside towards the pith. This gives a nicely concentric grain pattern when you look into the bowl. You can get a larger spoon if you carve from the pith side but the resulting hourglass pattern is not as pleasing to my eye.

Here are some of the knives I use:





These are home made from O1 annealed stock. The knives are cheap enough to buy but I like making them. You can purchase good quality Scandinavian knives for about $25 -$30. The curved knives come in different sweeps and left or right handed bevels. The straight knife has acute flat bevels on both sides, whereas the curved ones only on one side. Here is the grip I use to hollow the bowl:


Here is a link to Roy Underhill’s show featuring Peter Follansbee carving spoons:

https://www.pbs.org/woodwrightsshop/watch-on-line/featured-guests/peter-follansbee/

There is a lot of information packed in that show and is worthwhile watching. When I go camping or out to our friends cabin I will bring a hatchet and a few knives. Like Peter shows, I will rough out a blank with a hatchet and finish the spoons with knives. I am not real great with the hatchet and spoil some blanks but the wood is free and the hatchet work is in the beginning of the process. The skill is in how close you come to the line, leaving less for the knife to remove. At home I can use my band saw to rough out. Here are two blanks roughed out:


I used the hatchet for the right one and the band saw for the left one. In my shop I may use my workbench vise (or my new hi-vise) or my shave pony to work the spoon with a drawknife or spoke shave:


Here are the resulting spoons:


I will let them dry for a period and then clean them up a little. After they dry some more I finish them with walnut oil. I like the heat-treated Mahoney’s oil brand.

Some recent spoons:


Regards,

Paul Dzioba

P.S. The shave pony works great but it is a pain mobility wise having it strapped to you. A real shave horse is in the works.

Re: Spoon carving

#2

enjoyed the description

Bill Tindall, E.Tn.

I think my hands would cramp.

Re: Spoon carving

#3

Re: Spoon carving

Darrell LaRue

I carve spoons just to keep myself occupied at camp.

Very portable woodworking!

Re: Spoon carving

#4

Thanks, Paul

Joe shelton

I enjoyed looking through that, and I'll go back to when I finish this reply, to follow that link.

When you build the shavehorse, I hope you'll share that with us too.

Re: Spoon carving

#5

Re: Spoon carving

William Duffield

How did you set the straight blade in the dark handle? I notice that the other handles are split down the middle and glued back together, but I don't see a seam on that one.

I don't see a pic of your hatchet, so I'm shooting from the hip on this question. Have you tried a bearded hatchet? It allows you to hold your hand directly behind the blade for more control, since you can push the blade through the wood, instead of swinging and chopping. Of course, you can still swing the hatchet when you need to, as when harvesting the branch.

Re: Spoon carving

#6

Thanks Paul!

Raymond in Trenton NJ

They are great looking spoons. First time I’ve seen your fork. Makes me want to have a salad. They have a lightness and elegance about them. I remember that they felt great in the hand. Thanks for posting that.

Darrell, not just good for camp. This small WW kit is good for anywhere. I’ve taken them on work travel for evenings in the hotel. I’m such a party guy. Unlike a camp though, hotel carving requires a towel on your lap. Don’t ask me how I know this.

Regards,

Raymond

Re: Spoon carving

#7

Re: Spoon carving

Paul in NJ

Hi William,

the detail knife with the dark handle has a short tang and is epoxied into a hole drilled into the handle. The other knives have a longer and wider tang set into a channel on both halves of the handle. Here is my hatchet:


I am starting to sound like Todd H, but I found it as a rusty blob at a CRAFTS tailgate. It cleaned up very nice and with a new handle it works nicely. I think it might be a Collins as it has the same pattern of the camp axe I own.

Regards,

Paul Dzioba

Re: Spoon carving

#8

Re: Spoon carving

William Duffield

The hatchet looks good to me.

I'm thinking about remaking the handle on mine. Its curves are a bit less than optimum in a couple places, but I think the guy who made it knew what he was doing with the head. It was hand forged from an old farrier's rasp.

I'm still finessing the handle of the spoon knife you gave me.

I have questions on the third pic in your first post, of knives and hones in a MAYA cigar box: What do you use to charge the cylindrical hone that you have stowed in the cover? FeO? The flat hone is obviously loaded with Cr2O3. The wine cork is a nice touch, but the resolution is not good enough to read it from here.

Re: Spoon carving

#9

Re: Spoon carving

Pat Riley

When I make handles I cheat a little bit you could say. I use a modification of Nic Westermann's slotted dowel method.

Since I have the equipment, I use my hollow chisel mortiser. For a 1/2" wide x 1/8"-ish thick blade I cut a 1/2" x 1/4" (my smallest bit) mortise. Then I glue in 1/16" (or whatever is needed. The handle in the picture is for a 3/32" blade) spacers on each side using the blade to hold them in place (only glue the handle side). Not much glue is needed, this is just to hold them in place.


With the blade out, I can add small chamfers on top and bottom in order to fit the blade better. Shaping the handle is much easier with no fixed blade as well. Once everything is ready, I epoxy the blade in permanently. At this point, the epoxy completes attaching the shims as well.

It took some refining, but I have had good luck this way once I worked the bugs out. Fitting a curved hook knife takes some time. The only major problem is that the length of the handle is limited by the throw of the mortiser.

Re: Spoon carving

#10

Re: Spoon carving

Paul in NJ

I use Veritas green honing compound on both strops, the round one is just a little dirtier. Bogle on the cork.

Re: Spoon carving

#11

Re: Spoon carving

Paul in NJ

Pat,

that looks like a nice method if you can get enough epoxy into the mortice. I sometimes get a trapped air bubble with the thickened epoxy I use.

Regards,

Paul Dzioba

Re: Spoon carving

#12

Re: Spoon carving

Pat Riley

That has happened to me.

In the last few I have found that with a much tighter fit, thick epoxy isn't necessary. If I use thinner adhesive, the voids fill well with no trapped air. I have definitely cut off a few handles and started over though.

Re: Spoon carving

#13

Re: Spoon carving

Ron in Kokomo

Paul

Was so glad to see your post. I am back after a hiatus of 5 years or so, during which I have become addicted to spoon carving and 17th Century New England style carving. I have gone way off the deep end on knives.

Re: Spoon carving

#14

Re: Spoon carving

Ron in Kokomo

I have had good success drilling with a small bit and cleaning the mortise with a small knife and riffles.