Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Edge Longevity - soon forgotten

Posts

Edge Longevity - soon forgotten

#1

Edge Longevity - soon forgotten

David Weaver

I see there is a raging (well, it's more like an incense fire) debate on another forum about the longevity of V11 and already some misinformation about it (and i'll include XHP because my irons are nearly identical in feel and relative life to O1 as the factory V11 irons are).

I suppose there will always be fans of carbon steel - I think carbon steel is still the best choice for rough work as I'm convinced it nicks the least easily and when it does, grinding anything like that out is twice as fast as pretty much anything else on the market.

But for planing in clean wood, there isn't a carbon steel iron on earth that will match V11 or XHP if they are made to even remotely similar spec.

When comparing numbers from one board to the next, to have any relevant comparison, you'd need to use both irons on the same board, and probably rotating back and forth.

What I found in tests (since it's quickly forgotten) is not a longevity difference of 10 or 30% in long grain, rather a factor of 1.8 to slightly greater than 2 in several tests.

In the two full tests that I did head to head with my O1 iron (which would outlast probably 99.9% of stock stanley irons), the footage was 1570 feet for V11 to 780 for O1. when I made an xhp iron, first iron that I made - 4046 feet XHP, 2224 feet with my O1 iron.

I also used a ward plane just to test edge properties with less than optimal sharpening and footages were about 20-25% less than my O1 irons (still love ward irons, but using them side by side, it's undeniable that even good O1 has enough alloying in it to make a difference).

The only test that was close was end grain, V11 planed 1051 to O1s 992. The V11 was noticeably less painful to plane with (less resistance) and the gap where they were comfortable to use is wider than the final result - the last half of the O1 test was brutal. It was much more difficult to come up with a subjective stopping point with end grain than it was long grain.

I didn't test chisels, so I can't comment there.

The two different pieces of beech mentioned above should be enough illustration to clarify why you can't plane another board in another shop (not even the same type of wood as those beech boards came from the same dealer in the same load, possibly even from the same tree) and compare results in feet. A relative comparison has to be done.

This isn't a discussion about this or that entire system, just iron longevity in clear wood (Which is what most people do most of their planing in). I guess I need to make a couple of videos at some point to get the results posted publicly.

Re: Edge Longevity - soon forgotten

#2

It was a torture test that converted me.

Jim Matthews

My go to block plane dulled quickly while fitting plywood panels.

The half pint cofgin smoother with an XHP blade whistled through the work.

Once finished, I took it for sharpening only to find it still sharp enough to slice paper.

The fact that I can hone on two stones close to my finest Kanna closed the deal.

****

The wear characteristics of this "Adanantium" present a challenge in sharpening - I remove the wire edge before final honing. I think that's the conceptual error - presenting a wire edge to subsequent stones just leaves an ever finer burr.

Re: Edge Longevity - soon forgotten

#3

Re: It was a torture test that converted me.

David Weaver

I don't think V11 will become a favorite of the full bevel sharpeners, especially anyone using typical older stones and natural finishes.

I grind them religiously, and though I rarely use diamond hones, I put a secondary bevel on XHP with a diamond hone and then still usually use a washita to finish the very edge. The abrasion resistance makes it so that it takes a finer edge off of the washita than most of my carbon steel stuff.

It's an extremely forgiving steel to heat treat and use, though, aside from that. If you get the edge cleaned off - leave the wire edge or not, or get it a little hot on the grinder, it won't be affected much. It might lose a point or two, but it won't lose 10 or 15 like O1 does when blued.

But for regular sharpening, it's double the abrasive resistance and on full flat or rounded bevels, that'll be noticed!!! Doesn't spark much on a grinder - kind of miss the sparks.

Re: Edge Longevity - soon forgotten

#4

Jim, I'm hesitant to ask this...

Joe shelton

...for fear you'll say "With an incantation."

Still, how do you remove that wire edge before you progress to finer stones?

You don't have a zipper on them, do you?

Re: Edge Longevity - soon forgotten

#5

Re: Jim, I'm hesitant to ask this...

Jim Matthews

I use the same stone, as a "strop" to tease off the edge formed.

Please keep in mind that I use a single, convex bevel.

The stropping motion is just a pulling motion.

Re: Edge Longevity - soon forgotten

#6

By incantation,  do you mean...

Jim Matthews

Swearing?

Lyrics unrelated to the current song on the radio?

Rehearsing doomed arguments with SWMBO?

Each of these will contribute to positive outcomes, as they delay completion.

*****

The takeaway with these hard wearing steels (I have a knife with similar powdered steel) is that removing steel takes longer - there's no free lunch.

I spend more time on the coarsest stone with this stuff than 01.

I spend less time on the finest stone with this stuff than 01.

I sharpen far less often with this stuff.