Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Different finishing

Posts

Different finishing

#1

Different finishing

Bill Tindall, E.Tn.

First day warm enough to spray varnish in over a month.


I am becoming fond of Waterlox varnish. Dry enough to handle in 1.5 hours at 85 degrees. Dust-free in not much longer than lacquer on a cold day. I like the color and luster. Dries orders of magnitude faster than P&L 38 with about the same luster and color. Better build than General Arm-R-All. Been experimenting with all of these with gloss and +/- satin mix.

Sand to 220 cherry and 180 walnut. One coat gloss. sand at 400, Top coat of 1 part satin and 3 parts gloss. Sprayed with a 3 parts varnish and 1 part naptha dilution. Result glass smooth. Destined to granddaughter's bed rooms for bed side storage.

Waterlox must have a pile of catalyst in the formulation to cure this fast. Cans inerted with nitrogen after use.

Re: Different finishing

#2

Re: Different finishing

Wiley Horne

Hi Bill,

Thanks for sharing! Two questions:

1. What is the purpose of the gloss coat between 180/220 and 400 sanding?

2. Does the waterlox require spraying? Meaning can you wipe on without getting overlay streaks?

Wiley

Re: Different finishing

#3

Re: Different finishing

Bill Tindall, E.Tn.

1. What is the purpose of the gloss coat between 180/220 and 400 sanding? sealer and begin of thickness build. Gloss for all but the thin top layer gives the finish "depth". Normal procedure.

2. Does the waterlox require spraying? No/ test panels were brushed and it levels wonderfully. I can spray so I do spray. Took about 30 seconds to do the case. 15 seconds per drawer.

Re: Different finishing

#4

Re: Different finishing

Wiley Horne

Thanks. Do I recall that Frank Klaus uses waterlox also?

Wiley

Re: Different finishing

#5

Re: Different finishing

Joe shelton

Ellis was the first person to bring it to my attention, and since then I've used it extensively.

I think it's terrific.

Re: Different finishing

#6

Re: Different finishing

Howard Pollack

Bill (and others), which of the Waterlox products are you using? There are several different formulations according to their website? Do you use the Universal Sealer also? Thanks. -Howard

Re: Different finishing

#7

Re: Different finishing

David Weaver

I'm a marginal user of almost any accessory, but it's almost two years go now that I made a straight varnish - something that is known to gel in months in a jar.

I worried about that because it was expensive to make (less so the second time if I do it again).

I bought the stop loss bags directly from the manufacturer of them and even the varnish that is right up at the cap is perfect every time I open the bags. The bags can be reused, and they're about $3. Someone spraying large amounts at once may have less tolerance for filling them - but they definitely work.

Re: Different finishing

#8

Re: Different finishing

Don Stephan

Like you I really like the look of Waterlox on black cherry. My first trial though was on a cereal bowl, and after a couple weeks of use a call to the manufacturer confirmed that cured Waterlox will not stand up to dish soap. While soap likely likely will never be used on your pieces, it would have been nice to have a warning on the product label in case anyone (like me) thought of using the product on wooden bowls that would be washed.

Re: Different finishing

#9

Durability and Appearance

Bill Tindall, E.Tn.

The tops of these dressers are finished with conversion varnish for durability. While it initially doesn't look quite as good as the Waterlox it will look better after a few years of use. While a urethane varnish would have been a good choice too, it was too cold to cure it rapidly when these tops were finished. In the case of a bed side dresser the top will likely become obscured with stuff piled on it. What will show are the fronts and there I worry more about appearance.

My furniture doesn't/won't live in a museum or need to be marketed in a gallery. It will be judged by its function and appearance over time, with function being way more important than appearance, though the two don't need to be incompatible.

Appearance factors that need to be discerned by careful scrutiny don't have any relevance to furniture that stores socks. If it looks good from 10 feet across the room and continues to look good for years to come, that is good enough. Proportion and color are more important to appearance than other factors. Bottom line-to what ever extent appearance is an important factor in my designs the place to fret over appearance is in the proportions. I would judge color and luster of next most importance. I did several test panels to get the luster right on these pieces. Because of inlay, I was stuck with whatever color the combination of wood and finish provided.

Re: Different finishing

#10

Spray setup?

Martin S.

I have used Waterlox and like it, but I have always padded it on, with many coats.

Can you tell me about your spray setup? Type of sprayer, and what kind of nozzle?

I think spraying it would help me finish quicker and with a more even coating.

Thank you.

Re: Different finishing

#11

Anything that sprays lacquer

Bill Tindall, E.Tn.

Any gun that will spray lacquer will spray varnish, oil paint, shellac. I use a DeVilbiss with a #30 cap. There are lots of them used on Ebay. I usually thin varnish before spraying......start about 1 part solvent to 3 of varnish, or 2 to 3 if building a thinner close to the wood finish.

Learn spraying technique by spraying water on cardboard. Easy to see result and it will develop the technique.

Re: Different finishing

#12

I'm not bill....

David Weaver

..but I have a spraying setup that's simple and other than the guns, inexpensive.

* a cheap 15 amp HF oiled compressor (if you can wear it out, buy the warranty for $15 or whatever and get another one in the next 3 years - my first one lasted about 10 years before the pot metal fittings gave up - but the new one has brass - surprisingly tolerant of abuse by overcycling).

* some kind of regulator to have at the gun - which probably isn't essential, and if you're not spraying WB, some kind of moisture trap.

I tried some of the cheaper turbine setups and none of them was as good as an inexpensive compressor and a gun. They are more portable, I guess.

If you have a little bit of patience (enough to set your gun and avoid spraying heavy and getting sags), you'll be surprised how much easier it is than wiping - especially on intricate stuff. you need a bug free and relatively dirt-free area, though - and a decent organic vapor respirator (not expensive) - especially if you spray inside.

I'll defer to others on guns. I've bought expensive asturo guns and several HF guns - the HF stuff is hit or miss (same looking guns bought years apart don't seem to be the same quality in use).