Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Low Tech Pencil Fascination

Posts

Re: Low Tech Pencil Fascination

#26

Don't go square...

John in NM

They will break easier than round, at least until encased in wood, and probably after. I think the same principle applies with solid shapes as with holes cut in a skin - corners will tend to concentrate stresses, allowing fractures to start. The reason portholes are round. On the other hand, physics class was a looooong time ago! :D

Re: Low Tech Pencil Fascination

#27

Two things to try...

John in NM

A different sharpener or sharpen a better pencil. Either should tell you where the problem is. I mostly buy Ticonderogas, which still seem to be a fine pencil, at least for the shop. They sharpen evenly with the Boston Champions I've found over the years (3 at this point if you can believe it).


That funny clamp on the front keeps the pencil centered and pushes it into the sharpening mechanism. These were a staple of drafting shops and offices for decades before electrics came out.

Re: Low Tech Pencil Fascination

#28

Low tech pencil sharpening *LINK*

Bill Houghton, Sebastopol, CA

I've got a couple of similar sharpeners, but the spiral cutters have grown dull, it seems.

I alternate between Lee Valley's belt clip sharpener (link and pic below) and a lovely German one that someone (David Masury? Can't now recall) gave me years ago. Both are similar in concept to those little plastic blocks with a dull piece of steel in them that we were given as kids for sharpening pencils; but done right. I get good sharp tips with no stress on the lead. They do so well that I haven't been motivated to seek out new spiral cutters for the Bostons.


img

find it here

Re: Low Tech Pencil Fascination

#29

Looks similar to the Kum brand sharpeners

david weaver

Those still made in germany, and what I got 20 or 24 of (and am now running low on as I've dispensed them like party favors since I got them cheap and figured I could again at some point - that doesn't appear to be correct).

At any rate, I attempted to improve the cutter on the first one that I got, and have since realized that there's no point in it. they are wonderfully sharp when new, and the one that's in my shop bench doesn't show any sign of changing in sharpness.

The kids have various types upstairs at their desks that fit their whimsey (as in, bear shaped shaving enclosures, etc), but they're all junk. It's hard to overstate just how good the little german sharpeners are vs. anything else made of that style.

Re: Low Tech Pencil Fascination

#30

Rifling through Michaels last night..

david weaver

..waiting for a chinese takeout order to ripen, I was surprised to find an entire aisle of pens and pencils, including some tombow branded items....and nothing in 2, 3 or 5.x mm leads.

Staples is next. There's a gaggle of 2+ mm lead for clutch pencils, but all of it is struck by the internet issue for small items. Something that's $4 on the internet, and $5 at staples is better to get at staples because shipping and taxes make $4 the same as $9 instead.

Re: Low Tech Pencil Fascination

#31

Spiral cutters....

John in NM

I like the Bostons so much that I got some spare spiral cutters on ebay. Six bucks as I recall :D

Re: Low Tech Pencil Fascination

#32

Re: Spiral cutters....

david weaver

When you say spiral cutter, do you mean like the original hand crank type, or something else?

I have a boston ranger (had two, but my dad mooched one off of me) in the shop, as well as the kums.

Now that I've almost exhausted the kum supply, I've gone to ebay to find another batch (I like to give them out), and chanced upon a four way kum that's long point (the original two holes aren't long point).

The only sizable kum 2 hole listing for a pack is a display container with 50 of the magnesium types for $74. A little beyond my generosity :\

Re: Low Tech Pencil Fascination

#34

Re: That's what I was figuring...

david weaver

..but you never know!! There are manual (non crank) concave style sharpeners now that can point the pencils more acutely at the point than they do on the barrel.

The long point sharpener that I just ordered (princely sum of about $8.50) apparently doesn't just sharpen at a narrower taper, but allows sharpening two separate angles instead of a concave curve - steeper angle on the barrel and narrower angle on the lead.

I like the boston ranger (the cranker that I have in the shop), but on cheap pencils, it can get aggressive and break the leads out. it also sharpens a nice long point - with the caveat that the pencil has to be able to tolerate the long point.

Re: Low Tech Pencil Fascination

#35

Will try the leads, too, at some point...

david weaver

I've got a lot of things on my tinker list (guitars, chess pieces - turned a few more test pawns over the weekend, and putting together a piece of casework without the use of any power tools at all), but making the leads appears to be more attainable than I thought it would be.

As I gather it, pretty much mixing fine graphite and clay, firing at 1800F after extruding from something similar to a fondant extruder and allowing to dry, and then dip in wax. From what I was able to read, the amount of clay vs. graphite is the basic control for lead hardness.

Finding really good lead smooth for a reasonable price hasn't been that easy, and I have everything but the graphite already from making soap.