Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Who can straighten a D-7?

Posts

Who can straighten a D-7?

#1

Who can straighten a D-7?

Jason in OC

I am trying to restore an old Disston D-7 26" saw that I found in my dad's garage. The Disstonian Institute puts it in the 1947-1953 vintage. I have de-rusted it, but the final ~1/4 of the length (the small end, not the handle end) has a slight bow or kink in it. The rusty boot print indicated it was stepped on. Is there anyone who can straighten and retension the saw to make it usable again? Preferably in southern California? (Or Denver since I'll be moving there in a few months.)

Re: Who can straighten a D-7?

#2

Re: Who can straighten a D-7?

Eddie in Northern Alabama

http://woodcentral.com/articles/handtools/articles_866.shtml

Re: Who can straighten a D-7?

#4

Re: Who can straighten a D-7?

Jim Matthews

I'm with David - if you're careful, you should be able to straighten this yourself.

If the saw is to be used, sharpen it and see if it cuts straight as it is - it might not need adjustment.

Re: Who can straighten a D-7?

#5

Re: Who can straighten a D-7?

Joe shelton

Thanks for that video. Hope you didn't get in trouble for taking the time to make it...

Re: Who can straighten a D-7?

#6

Glad to see this discussion, I've got a bent

Keith Newton

22" Ontario machete that I use a lot. When I head out on the 4wheeler, Ive found a good place to easily store and retrieve it, by sticking it under the back rack. However a few weeks ago, the handle got outside of the fender's protection as I drove through a tight squeeze between some oak saplings. The handle caught, and bent around past 90º before snapping around.

At first I was just sick to see this FINE woodworking tool destroyed. Then I figured, what is there to loose to try and straighten it, so found the nearest tree with a low fork, which I shoved the blade between the tight V, then bent it back. It took several tries before I got it reasonably straight. However, ever since whenever I land a hard swing into something that is unyielding, it wants to bend back. I would like to think that hammering/ re-tensioning it would solve that problem.

I had been wondering if I would need to use heat to get the memory right?

Re: Who can straighten a D-7?

#7

I've had a real struggle with this

Christopher Fitch Memphis

I have a couple of Disstons I've picked up at estate sales that have slight issues. I actually won't get one with any sort of bend/kink now just because it's been a pain.

I have one that has a slight curve on the top of the blade and I have another with a very slight warp. I've been able to straighten them a bit but it's still not good enough.

One thing that is not clear to me still: do I tap on the side that is concave (ie. the inside the bend) or on the convex side (ie. the outside of the bend)?

I've read conflicting info about this and can't find a definite answer (or more likely I'm just not understanding what has been written about it).

As to who might be able to straighten saws:

Ron Herman *might* be an option

http://www.woodworkingwithron.com/

or Daryl Weir

http://oldsawsrestored.embarqspace.com/

or other saw makers.

Re: Who can straighten a D-7?

#8

Re: Who can straighten a D-7?

Bill Houghton, Sebastopol, CA

Have you considered just cutting off the bent part and treating it as a panel saw? Or are there familial/sentimental reasons not to do so?

Re: Who can straighten a D-7?

#9

Another option

Patrick Chase

I bet Pete Taran at vintagesaws.com could also do the job.

In addition to selling a lot of Disstons, he founded and ran the first of the "modern" Western sawmakers (Independence Tool, which went on to become Lie-Nielsen's sawmaking business).

Re: Who can straighten a D-7?

#10

Re: Who can straighten a D-7?

David Weaver

I can't remember if I did. My wife would prefer a house with no woodworking in it and a husband who is not tied up with hobbies (always on standby).

Re: Who can straighten a D-7?

#11

Re: I've had a real struggle with this

david weaver

Hi Chris - I can only offer my thoughts. I've hammered all of my older bowed saws, and all have turned out fine. I've also hammered some tension back into a saw that I deburred the entire rusted top layer off of, and it also turned out fine (it was a pretty sorry excuse for a saw after heavy deburring, though, which one should expect given the tension is in the surface and not the rest of the plate - but that's to our benefit).

Anyway, I read smalser's tutorial, but to me, this is something you just have to play with until you see how your setup works.

A polished hammer with a convex face and a smooth metal backing surface and you can move metal. What I've found with my setup is that if I have a warp, I put the high side of the warp facing up, then bend the saw by hand so that it's contacting the anvil and tap on it. I'm "hammering the bump down", which is the opposite of what I thought would occur.

But however it works with your specific setup, it doesn't matter as long as you experiment some, observe what's going on and go relatively slow. If you hammer on the high side and it goes down, then do that when you need to. If you hammer on the low side and it comes back toward you instead of moving away, then do that.

If you were local, I'd hammer your saws for you. I hate to ship saws, though, because even if they're stuffed into a box with some pressure on teh saw somewhere, they can take a "set" of the curvature they were forced into in the box. That's actually what prompted me to experiment and figure it out - MJD sent me a nice box of saws and some dodo there taped them all together tightly, which means some will curve (think wrapping the toes as tightly as you can, then the center, then the handles - all saws lined up the same way. One may be lucky enough to be straight in the group, but the rest will be bent). They took on the curvature permanently just from being bound together tightly like that.

Re: Who can straighten a D-7?

#12

Just to follow up. It was easier than expected.

Keith Newton

I couldn't flex this blade like a thinner handsaw. However I've got my Grandfather's old anvil, which doesn't have any sharp corners anywhere. I suspect it was already old before he got it over 100 years ago. This wasn't a bad thing though, since there was a depression around the Hardy Hole, which I figured I could use to my advantage by hammering the crown over that slight hollow.

Re: Who can straighten a D-7?

#13

Re: Who can straighten a D-7?

Glenn Mackey

I have no trouble straightening saws. I lay the saw crown up on a hardwood board and gently tap the point of kink or apex with a hammer. I determine the point where the damage originated and tap along the cutting edge in both directions and then across the width. You tap and check, tap and check till its straight. Works every time. Use a hammer with a curve across the face. Experiment with how hard you need to hit the blade - usually very gently as in almost just dropping the hammer. This is not rocket science.