Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

waxing a dovetail saw

Posts

waxing a dovetail saw

#1

Jack Guzman from Maine

waxing a dovetail saw

Jack Guzman from Maine

I am building a bunch of drawers. The client wants hand cut dovetails . Who am I to argue? I'm using 5/8" poplar for the drawer sides and cutting both sides at once,clamped together. The sawing was getting a little tedious so I made a swipe along the sides of the saw with household wax. Instant relief! Took all the work out of it. All I need to do is concentrate on steering.

What I want to know is if anyone else uses wax on a dovetail saw. Should I worry about transferred wax affecting the glue? It doesn't take much wax to get the saw sliding with ease.---Jack

Re: waxing a dovetail saw

#2

Re: waxing a dovetail saw

david weaver

If it's tight and heat is a problem, I either use paraffin or beeswax, and sometimes paste wax - whatever is in reach.

I've never had tails or tenons refuse to hold because of it.

Re: waxing a dovetail saw

#3

Re: waxing a dovetail saw

Ron in Sterling, CT

Hi Jack,

I wax all my handsaws with Johnsons Paste Wax. They slide so much easier, and it is a good rust barrier for a while. I have never had any finishing problems as a result of using it.

Ron

Re: waxing a dovetail saw

#4

Re: waxing a dovetail saw

William Duffield

Doesn't everyone? I use beeswax or a plumber's candle.

Re: waxing a dovetail saw

#5

Yes and No

Derek Cohen (in Perth, Australia)

Waxing does work. However, this is usually a symptom that there is insufficient set on the teeth. A smidgeon more and the saw may glide without wax.

Regards from Perth

Derek

Re: waxing a dovetail saw

#6

Re: waxing a dovetail saw

joe mohnike

I have used dried out bar soap. Does the same job a wax but easy cleanup.

Re: waxing a dovetail saw

#7

Re: waxing a dovetail saw

William Duffield

Be careful with soap. It is hygroscopic, and can attract moisture, and rust your saw plate. Same problem with using it to lubricate steel screws.

Re: waxing a dovetail saw

#8

Re: waxing a dovetail saw

Warren in Lancaster, PA

What we call poplar in the woodworking trade here in eastern United States is Lireodendron tulipifera, which is in the Magnolia family. It is a traditional secondary wood, especially in the Mid Atlantic region.

One peculiarity of poplar is the occasional need for lubrication. One can go for months working other timbers, with no lubrication at all on planes and saws, then have some piece of poplar demand it. Sometimes one can get screeching planing end grain. Lubrication does not need to be very much and it does not need to be often or regular. Wax, oil or grease will work.

Re: waxing a dovetail saw

#9

Jack Guzman from Maine

Re: Yes and No

Jack Guzman from Maine

Good point Derek,however not in this case. The saw cuts perfectly for me but I wanted to double up the sides to speed things up. The extra thickness was more than the saw was intended for and I had to work harder. The extra effort needed was getting tiresome,hence the wax. ---Jack

Re: waxing a dovetail saw

#10

Re: waxing a dovetail saw

North of the Border

Yes.

Candle wax for sawing, gang cutting or not as well as for planing.

Soap wax, no as another poster pointed out. For screw lubricant, I use the toilet bowl wax ring.

Re: waxing a dovetail saw

#11

Re: waxing a dovetail saw

Ron Pemberton

Ditto, Ditto

Re: waxing a dovetail saw

#12

Re: waxing a dovetail saw

Ray

When I purchased LV dovetails saws, they came with the recommendation of not using beeswax. Something related to possibly clogging the teeth.

Re: waxing a dovetail saw

#13

Re: waxing a dovetail saw

roger lance

Ray is correct. LV recommends paraffin to allow the saw to run more smoothly through the cut....but, also states not to use beeswax because beeswax will gum everything up.

Re: waxing a dovetail saw

#14

Re: waxing a dovetail saw

William Duffield

It seems like it would depend on whether you apply it to the saw plate or the teeth. What would keep paraffin from filling the gullets and sticking to saw dust in the teeth? Sure, it has a higher melting point than beeswax, but a little friction will soon warm the teeth and the wax and start to liquify it.

Re: waxing a dovetail saw

#15

bridger

Re: waxing a dovetail saw

Bridger

I for many years used beeswax. When my chunk of beeswax ran out I replaced it with paraffin wax. They worked about the same for me. Never had problems with clogging. You just need a tiny scribble.