Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

200+ woodworking book reviews

Registering a skew rabbet plane

Posts

Registering a skew rabbet plane

#1

Registering a skew rabbet plane

Josko Catipovic

I'm trying to get used to my LV skew rabbet plane. My rabbets are ending up wavy, with the angle (of the cut surface) sort of drooping a bit towards the ends. ('Ends' defined as one end against the uncut surface, and the other at the end of the plank, with the 'length' as rabbet width.)

I'd assumed a rabbet plane registers on the rabbet it's cutrting, but it doesn't seem to be working for me. I thought about registering the fence against the end, but my workpieceends are too narrow to offer much of a registration surface. Mounting the plane against the workbench side and using the vertical workbench surface seems quite finicky.

So, is it reasonable to expect an even angle on the rabbet bottom, and if so, what's the appropriate surface to register the plane against?

Re: Registering a skew rabbet plane

#2

Re: Registering a skew rabbet plane

Derek Cohen (in Perth, Australia)

My rabbets are ending up wavy, with the angle (of the cut surface) sort of drooping a bit towards the ends...

I'd assumed a rabbet plane registers on the rabbet it's cutrting, but it doesn't seem to be working for me. I thought about registering the fence against the end, but my workpieceends are too narrow to offer much of a registration surface. Mounting the plane against the workbench side and using the vertical workbench surface seems quite finicky.

Hi Josko

I am not sure if I understand the second part of your question, but the first bit is clear.

All rebate/rabbet planes, including the Veritas skew rabbet, require (1) that the blade is set a hair beyond the body and that (2) the nicker is aligned with this (used when planing across the grain). The reason for the blade set this way is that it needs to cut into the inside corner of the rebate. If the plane is not set up this way, then you will create a progression of increasing "steps" rather than a nice, square inside corner.

I would recommend that you add a deep subfence to your Skew Rabbet, such this this one of mine ...


This increases registration, especially if you also align the work piece with the side of your bench, which ensures a vertical orientation.

I also removed the front knob, since one should not grasp the plane at that point. Instead, I place my thumb on that spot, and push with my palm against the fence. This holds the plane firmly against the work piece.


Regards from Perth

Derek

Re: Registering a skew rabbet plane

#3

Re: Registering a skew rabbet plane

Josko Catipovic

Thank you, Derek,

it seems I didn't define my problem adequately. If you think of the panel such that the bottom of the rabbet is horizontal, the vertical edge (at the insdside of the rabbet) is fine. I've fiddled with the blade and nicker so the 'inside wall' of the rabbet doesn't creep inward and is nicely vertical.

My issue is with the horizontal part of the rabbet. I can't get it to be horizontal enough, and the angle is a few degrees off horizontal, tilted towards the outside of the panel. Worse, it's not uniform.

I tried setitng up the panel flush with the workbench edge, and what happens is that if they're not perfectly aligned, I get a variable rabbet width. Somehow I get a sense the tool is not intended to work this way, but then, I'm new to it. Maybe it is.

My probleml is that if I let the panel (being rabbeted) overhang the workbench, register the fence against the panel edge, and the plane sole against the rabbet being cut, I don't get a uniform rabbet angle. Again, if the desired angle for the rabbet bottom is zero (flat, horizontal), my rabbets end up with a variable angle, ranging from flat to a couple degrees towards the outside. I feel like I need to clean up the rabbet bottom after the skew plane is done with it.

Re: Registering a skew rabbet plane

#4

Re: Registering a skew rabbet plane

Joseph Piotrowski

make sure you fence is sure to the plane bottom.

also, i notice that its user error on my part. i made 2 rabbet perfect. i made 2 like your describing.

make sure the the fence is registered to a surface 90 to the rabbet. make sure you keep it that way on entering the rabbet.

there are a few youtube videos out there going over this issue. do a quick search.

Re: Registering a skew rabbet plane

#5

Re: Registering a skew rabbet plane

roger lance

If your plane is setting flat on your board and your fence is being maintained against the end of your board and you are getting a rabbet that is not flat.....then, perhaps your blade is not completely parallel.

Your blade might be protruding more at the tip and less at the heel which could give you an angled rabbet.

But, I'm somewhat new to this also.....so.....

Re: Registering a skew rabbet plane

#6

Re: Registering a skew rabbet plane

Derek Cohen (in Perth, Australia)

My probleml is that if I let the panel (being rabbeted) overhang the workbench, register the fence against the panel edge, and the plane sole against the rabbet being cut, I don't get a uniform rabbet angle. Again, if the desired angle for the rabbet bottom is zero (flat, horizontal), my rabbets end up with a variable angle, ranging from flat to a couple degrees towards the outside. I feel like I need to clean up the rabbet bottom after the skew plane is done with it.

Hi Josko

Assuming the blade is set square to the sole ...

I can obtain perfectly flat and coplanar bottoms by either (1) aligning the side of the panel with the edge of my bench, and using the deeper fence, as mentioned in my previous post. This ensures that plane is cutting square. Or (2) I simply run extend the board and just run the plane as I have developed a decent eye for vertical.

Setting the depth stop ensures that the rebate is an even depth.

Regards from Perth

Derek

Re: Registering a skew rabbet plane

#7

Re: Registering a skew rabbet plane

Wiley Horne--So. Calif.

That's what I'm wondering too. Suggest retract the blade until it is out of sight above the sole; then sight along the sole and begin to lower the blade slowly into cutting position. Does the 'outside' blade tip appear before the inner part? If you can't tell, get the blade into cutting position as best you can, and take a thin stick of wood and shave a strip off the thin edge, first from the outside and then from the inside of the blade--are the strips shaved from the outside and inside the same thickness to your eye?

Wiley

Re: Registering a skew rabbet plane

#8

Re: Registering a skew rabbet plane *LINK*

Jim Matthews

How do you mark out your panels?

If using a cutting gauge, you should see the knife mark

part with the panel as you get close to depth.

With no depth stop, you're likely following a natural

curve as you reach the end.

Perhaps a notched block to check thickness​ as you go might help? It would look something like the "female" half of a bridle joint.

http://wiki.dtonline.org/index.php/File:BridleJoints.png


img

http://wiki.dtonline.org/index.php/File:BridleJoints.png

Re: Registering a skew rabbet plane

#9

it's in the wrist

ian

It takes a little practice to hold your dominant wrist with just the right amount of stiffness.

What you are describing is, in my experience, the result of a slight rotation of your wrist through the planning stroke.

After setting the blade correctly, and holding the plane's fence firmly against the work, it's still possible to slightly twist the plane so that the bottom of the rabbet ends up tilted down from the horizontal.

all I can really suggest is to practice on thicker board till you learn what is the right "just so" hold and stance to get a flat bottomed rebate.