Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Premium Live Edge Slabs, Hand-Selected in the Berkshires. Shop Unique Hardwood Pieces.

dovetails,Rabbits and dado's oh my!

Posts

dovetails,Rabbits and dado's oh my!

#1

dovetails,Rabbits and dado's oh my!

Joseph Piotrowski

i'm moving along on my shop cabinets. i spent the weekend getting the pieces cut to size. i hand jointed one side of each board. i soon found out a 9.5" wide board can become a 9 inch board :).

but once i did that i cheated and rip it to size on the table saw. i don't really have a sufficient hand rip raw. i did want to use hand tools, but my hand tools and skills are lacking so i'm allowing it :). in the future i'll have my band saw setup and that would also work well.

i cut the pins on one board and remembered i wanted to rabbit the backs. so i test cut a few rabbiots on scrap, using different methods. i figured out the best method with the tools i have and could actually get a decent rabbit.

it takes a while as i have to sharpen and setup each tool i try to use. not to mention figuring out how to use the workbench i have to get it done.harbor freight special.

i also had to fight the urge to leave the rabbits alone after test cuts and buy a vertias skew rabbit plane.

i soon tossed chopping them out with a chisel method.i settled on using my Ulma wood body shoulder plane over a skewed rabbit plane(old wood one). the ulma has a cap iron and that seams better IMO.. i tuned cap and iron up (free hand) hand it wasn't as awesome as the YouTube vidoes but now after 14 feet of 3/8 by 1/2 rabbits i'm comfortable enough to skip buying a tool for now :)

for this cabinet i'm just mitering the back end where the groove is and cutting dovetails for the rest.

the next case i'm stepping up my game with shouldered dovetails and mitering both edges. should look nice and good practice.

I've already cut a bunch of test dado's and have a process down that should be ok since i'm only doing a few. one or two per case.

dovetailing is a pain. literally. without any face/leg vice, i had to use clamps to hold the wood. but bending over was no joy.. 2 advil later i decided this has to change. ideally i want to have a benchcrafted moxin vise but that cost more than my whole bench. so i need to rig up something to raise the height and be cheap to construct. baby steps :)

so now its build something to allow me to build what i wanted! beginning are rough until you get all your shop squared away!

i see a proper workbench in my future.

thanks for reading my ramblings. i though id share some progress as many of you have given me ideas and tips.

thanks,

Joe P.

Re: dovetails,Rabbits and dado's oh my!

#2

Re: dovetails,Rabbits and dado's oh my!

Bill Houghton, Sebastopol, CA

Sensible of you to try the tools you had before buying a new one. Sounds like you're having fun (mostly, except for the Advil part) and learning a lot, while making something you want. That's shop time at its best.

Re: dovetails,Rabbits and dado's oh my!

#3

Moxon option

Wiley Horne--So. Calif.

Hi Joe,

Great work! Everything is to the good, and hard ways is best of all. Because you remember.

On the Moxon, you may have been speaking of the Abraham version, which is truly the Daimler of the category. If you want the functionality without the price, you might look at just buying some hardware, as here:

https://www.toolsforworkingwood.com/store/item/MS-MOX.XX

And seeing the thing broken down like this might give you some ideas you could do with other hardware of your own choosing.

Keep it up!

Wiley

Re: dovetails,Rabbits and dado's oh my!

#4

Re: Moxon option

Tony

I can't remember where I've seen it but I've read about using two f clamps and a couple of boards to make a moxon style clamp setup. Two wooden screw viseattached to the edge of the bench will work as well. If you have a workmate then it can be used for this too.

Re: dovetails,Rabbits and dado's oh my!

#5

Re: dovetails,Rabbits and dado's oh my!

roger lance

Joseph.....if you have a table saw, jointer, and planer; I'd suggest that you build a proper bench.....something heavy.....with good vises.....and at a height that's comfortable for you.

You don't have to go lavish.....it doesn't have to be all hard maple.....but, a good bench makes a big difference.

Re: dovetails,Rabbits and dado's oh my!

#6

Re: Moxon option

Derek Cohen (in Perth, Australia)

Hi Tony

Bearing in mind that you really only need to dovetail boards no thicker than 1" .... let's say 1 1/2" maximum ... you can use steel bolts that run around 6" long and 1/2" diameter (This would use a backboard and chop each 1 3/4" - 2" thick). Recess the matching nuts for these bolts.

I'd rather use this set up than re-tread clamps (which are clumsy to secure).

All-in-all, a moxon vise could cost you about $5.

My own uses wooden screws that I made using a screw box. I've also made wooden screws using a router and V-bit.


Regards from Perth

Derek

Re: dovetails,Rabbits and dado's oh my!

#7

someday...

Joseph Piotrowski

probably soon, i will build a bench. there is a lot of advice and opinions on benches out there. not necessary contradictory but certainly varied in scope of features and dimensions.

researching theory can only get me so far, so some actual experience with tools at a bench is going to be enlightening. maybe after 4 or 5 projects, i will know enough to figure out what it is that i need. i only want to build one bench if i can help it. they take a lot of time and that i'm short on.

for now this pathetic little bench is teaching me all it's short comings for even the simplest task. working through the issue and overcoming them will teach me what features, size i really need for the projects i make. at least that is what i'm telling my self(for now) :)

Re: dovetails,Rabbits and dado's oh my!

#8

Re: Moxon option

Joseph Piotrowski

thanks for that link, that is very affordable and look like it will be nice. i have to consider that option for sure.

Re: dovetails,Rabbits and dado's oh my!

#9

thanks

Joseph Piotrowski

that is another good option and very cheap. use what i have! i jut need to be creative.

Re: dovetails,Rabbits and dado's oh my!

#10

nice vice

Joseph Piotrowski

and advice..

:D

thanks.

Re: dovetails,Rabbits and dado's oh my!

#11

Re: someday...

roger lance

It's wise to gain some experience to help guide you in the features you'll want in your bench.

I'll advise you to not skimp on materials.....especially vises.....the money you spend now will not be of much of a concern years from now.....but how well the bench works will be. Most of us build one bench and stay with it for years and years.....whether the bench is good or lacking.....so plan well.

I'd also recommend Scott Landis' The Workbench Book.....a great reference on a wide variety of bench types to meet the needs of a spectrum of woodworkers.