New WoodChat!
Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Build it. Rock it. Rockler has your woodworking tools.

It's so quiet ... so an update

Posts

Re: It's so quiet ... so an update

#2

Re: It's so quiet ... so an update

Michael Brady

That is really good-looking, Derek. It also seems to be a design from within yourself rather than being derivative. Am I correct about that?

Re: It's so quiet ... so an update

#3

Re: It's so quiet ... so an update

Bruce Mack

That's a bold use of figured wood, flowing and cresting from drawer to drawer (with no external evidence of a drawer frame that I can see). A knockout.

Re: It's so quiet ... so an update

#4

Re: It's so quiet ... so an update

Derek Cohen (in Perth, Australia)

Hi Michael

The design is one I have had in mind for a while. When I first posted it here I simplified it a little - mainly because I thought it would be too difficult. Then the guys here pushed a little, and I took a deep breath and decided to just do it.

It is interesting that building something that appears complex becomes easier when you recognise that it is just working to lines. What is difficult is deciding where those lines go :) In this case, the headache was deciding where the lines went for all the compound joints.

Regards from Perth

Derek

Re: It's so quiet ... so an update

#5

Re: It's so quiet ... so an update

Derek Cohen (in Perth, Australia)

That's a bold use of figured wood, flowing and cresting from drawer to drawer (with no external evidence of a drawer frame that I can see).

Hi Bruce

There will be a very slight gap between the drawers, essentially a thin dark line. I shall remove about 1.5mm from the lower edge of each drawer. I feel that this is needed to add a little separation of the figure in each drawer, otherwise it will be too busy and overwhelming.

Regards from Perth

Derek

Re: It's so quiet ... so an update

#6

Re: It's so quiet ... so an update

Hank Knight

Derek, that's quite a nice piece. I've enjoyed watching your progress. What are you going to use for drawer pulls? I'm having a hard time imagining hardware that won't distract from the beauty of the beautiful wood front.

Re: It's so quiet ... so an update

#7

Re: Looks Nice Derek..

david weaver

Very nice... I hope the lingerie that goes in it can measure up to the chest!

Re: It's so quiet ... so an update

#8

Re: It's so quiet ... so an update

Derek Cohen (in Perth, Australia)

Hi Hank

The handles have been a huge headache, but I have settled on what I think works best (hopefully .. I have said this more than once!).

Finding a design that will blend in ..

Earlier I had decided that I would make handles such as those below from Jarrah. Just a single row down the centre.


Now I am back to the original plan, a double row of small, round pulls. I turned a few this past weekend, very similar to a Shaker knob, but shorter.

I was thinking of Ebony at one time, but my wife is adamant that they should be the same Jarrah as the drawer fronts. I agree after making a few from some scrap.

Your thoughts?

Regards from Perth

Derek

Re: It's so quiet ... so an update

#9

Re: Looks Nice Derek..

Derek Cohen (in Perth, Australia)

Thanks David.

p.s. It is not really for lingerie. That was just a joke that stuck. I did promise Lynndy a chest of drawers, and wanted something with feminine lines.

Regards from Perth

Derek

Re: It's so quiet ... so an update

#10

Re: It's so quiet ... so an update

Brian Holcombe

I think what you are describing is a nice choice.

Nice work as always, and I love the London dovetails.

Re: It's so quiet ... so an update

#11

Re: It's so quiet ... so an update

Gary B.

Derek,

That is simply beautiful! I love the drawer fronts as is. Too good looking for any pulls in my humble opinion. I know hardware seems to be taboo on this forum, but have you considered a push mechanism, so you push it and it pops the drawer out enough to reach into and pull out?

Re: It's so quiet ... so an update

#12

Re: It's so quiet ... so an update

Derek Cohen (in Perth, Australia)

I love the drawer fronts as is. Too good looking for any pulls in my humble opinion. I know hardware seems to be taboo on this forum, but have you considered a push mechanism, so you push it and it pops the drawer out enough to reach into and pull out?

Hi Gary

My original concept was for drawers to use a push mechanism. In fact I went out and purchased a bunch of them for this project. The problem is (1) they are plastic and and made for kitchen drawers, and I have doubts that they will last 10 years, never mind 100. (2) I am not confident that they will be strong enough to push the drawer out by a few inches with the added weigh of clothes or whatever.

As a result I abandoned that idea. I still like the concept, and it you can come up with metal mechanisms, I would reconsider.

Regards from Perth

Derek