New WoodChat!
Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Premium Domestic, Figured & Live Edge Hardwoods in Stock. Best Prices for Serious Woodworkers.

Good Eyes, Warren!

Posts

Re: Good Eyes, Warren!

#26

Re: Carpet

Brian Holcombe

My wife's requirement for removing the carpet is that it must wear out first. So, wear out it I will....but unfortunately it wears like steel plate, lol.

Re: Good Eyes, Warren!

#27

Another question

Bill Tindall, E.Tn.

"They are going to be line plan-file drawers". Don't know what this drawer is.

BTW, no problem getting a 600 pound band saw into a basement. Disassemble it. After removing motor, table and wheels from a 20" Delta all the parts were easily carried into the basement. The 1100 pound lathe was a greater challenge. When we sell the house maybe a woodworker will buy it. :)

Re: Good Eyes, Warren!

#28

Re: Another question

Brian Holcombe

That's a typo, it should say they're going to be like* plan file drawers. Plan file drawers are make for holding drawings, so they're thin and wide.

In order to be able to nicely layout jewelry I decided to ditch the dividers and just make big flat surfaces so that she can spread out her jewelry.

I have been wondering what a MM16 can be broken down into, but getting one also requires me to renegotiate where the storage space for extra junk moves....which is a more difficult task than moving 600lbs.

Re: Good Eyes, Warren!

#29

drawers

Bill Tindall, E.Tn.

"plan file drawers"

I went with the same style for the Spice Box jewelry boxes I have made. It may not look as cute as a divided drawer but I agree with the more practical side of it.

Daughter, who sews, made the velvet liners (leave knees weak velvet prices). She cut poster board to be a loose fit to the drawer then wrapped it with velvet and glued the fold on the back side of the poster board. Additionally she snipped the fabric that folded under the corners so as to remove some. The result is there are fewer layers being folded together under each corner. I do not have a picture of this process but could get her to describe it better if need be.

Are you going to finish the door panels before gluing?

Re: Good Eyes, Warren!

#30

Re: drawers

Brian Holcombe

The doors are glued up :D I decided against finishing them since the panels don't float.

I appreciate the offer, and it might be helpful to see how you guys lined it. I lined a few boxes in a very similar fashion to how you describe. I've been debating doing the same for this or changing it.

Alternatively I have considered using drawer slips and simply applying the leather directly to the drawer bottom (plywood). Not sure how I feel about the aesthetic of drawer slips, but I do realize they add strength to the drawer assembly….but also not sure that is needed.

Re: Good Eyes, Warren!

#31

Update on the build

Brian Holcombe

My drawer fronts are now most of the way complete. I plan to move along with the majority of the rest of the work before deciding what to do on the drawer pulls. My intended plans will not work out as my mom has insisted that I build necklace hangers into the door fronts....using up all of the available space between the drawers and the doors.

So, I am building this setup and likely will complete the drawers before actually deciding on how to open them. Poor planning, I know, but I expect it will work out. Worst case I can do the Nakashima style pull, something I have been very much trying to avoid.


Showing the molding details inside the case, these are not actually attached yet except by how they lock into the inside panels




The inside of the doors will be lined with leather, with a thin open space for the necklaces covered by battens and veneered panels


This is a very rough mock-up of the inside of the door without the panel


and with the panel (uncut)


Re: Good Eyes, Warren!

#32

Re: Update on the build

Bill Houghton, Sebastopol, CA

Very nice.

I know there'll be a door, but I was struck by how attractive the deep setback is as it stands. You may have a new design feature for future cabinets!

Re: Good Eyes, Warren!

#33

Re: Update on the build

Brian Holcombe

Thanks Bill!

My biggest debate currently is how to go about flush drawer pulls. Though I have left enough space between the door liners for small pulls ( I think about 1/2" by 4"~). So I may still be able to use pulls.

I initially cut for a pull in the bottom panel just under the first door. That was how I was intending all of them to go, but have debated wether or not I should continue in that fashion.

Re: Good Eyes, Warren!

#34

Brian, how do you apply veneer?

Tom Colligan

With HHG, a press, or by vacuum? Thanks, a really great work.

Re: Good Eyes, Warren!

#35

Re: Brian, how do you apply veneer?

Brian Holcombe

I use a vacuum bag for veneering. It's hard to tell from the photos, but I also veneered the backside of that plywood in paperbacked white oak.

Re: Good Eyes, Warren!

#36

Re: Brian, how do you apply veneer?

Brian Holcombe

So, after making those veneer panels, squaring them and prepping them for use….they turned out to be a hair thick and I decided to shelve them….hah, just the way it goes on this sort of planning.

Here is my solution as produced, the doors still await a hanger system (my father is making that, in brass….probably).


Sorry, minimal work in progress shots, as this one was a 'seat of the pants' design process. It's difficult to document detail while thinking through expected results.