New WoodChat!
Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Rare Exotic & Domestic Hardwoods, Milled In-House in Oregon. Browse Unique Stock.

Leg Vise (Parallel Guide) Question

Posts

Re: Leg Vise (Parallel Guide) Question

#26

so far...

david weaver

I took a picture tonight only because I was excited to get the legs on the thing and turn it over and get it upright tonight. It's not the heaviest thing I've ever lifted without any assistance, but it's close!

All ash, except one of the boards was something that's not ash, so one of the rear legs isn't actually ash. I have no clue what it is, I think it's foreign, it reminds me of hardwoods in asian hardwood furniture (and it was much heavier than ash) and has no open pores. Well, the floor between the stretchers isn't ash, either, it's white pine.

The caps will make it 4 inches longer, totaling 7 feet (it's all I have space for), and I need to make wedges for the tops of the stretchers yet (couldn't get on with the idea of paying for bench bolts) and cut the stretchers back.

One thing I didn't anticipate correctly, since I didn't use any plans, was that the stretcher on the front is one board back. I like having the stretcher like that, though, and would probably do it that way, anyhow. The deadman will have to be modified slightly so that it's flush with the front, but no big problem.

P1080240

I planed a patch of the ash, it's not like it all runs the same direction. No problem with a cap iron, though. It has smaller pores than I expected and I'm pretty happy with it. I'd have preferred beech, but it's not as loud as maple would've been, and I don't have access to cheap beech.

P1080245

Re: Leg Vise (Parallel Guide) Question

#27

Re: so far...

Brian Holcombe

Looking pretty nice! I like the idea of wedges for the stretchers rather than bolts, I can do without bolts in most things.

Ash is great, my only regret is that I started using ash after maple. Had I gone the other way around none of my shop furniture would be maple.

Re: Leg Vise (Parallel Guide) Question

#28

Re: so far...

William Duffield

The trade-offs you will experience from moving the parallel guide higher are that for the same pressure applied to the work at the top of the jaw, the forces on both your wood screw and the pin in the parallel guide will increase. There's not much you can do about the screw, but you can increase the diameter of the pin to compensate.

You could always cut another mortise, either closed or open at the bottom, below the stretcher. If it bothers you, you could even fill the mortise you already have.

Have you cut a groove in the lower surface of the top for the deadman to ride in? You need one. Also, you will need some sort of rail on top of the bottom front stretcher, also to track the deadman. The top groove will need to be deeper than the stretcher rail is high, so you can lift the deadman out, to get it out of the way when you are not edge jointing. An alternative is a free standing deadman.

Is that a Record metal vise sitting uninstalled on the top of the bench in your picture? Why not use that instead? It's a lot easier to install, it has minuscule problems with racking, especially compared to a leg vise, and its a lot quicker to change the jaw opening (if you think that is important for the work you do). I do, however, agree with Warren that the number of times you will need to make a coarse change to the jaw opening vs. the number of times you will open and close the jaw with a half turn of the screw, for most types of joinery work, will be very small.

Re: Leg Vise (Parallel Guide) Question

#29

Re: so far...

david weaver

The top groove is in line with the rail. You'll see when I post a finished picture how the dead man lifts in and out. It's essentially going to end up being 3 1/2 inches thick in some parts.

I had thought about a board jack before I even started the bench, because I certainly don't have a deadman at this point and have gotten along fine without one, but I'll go with the deadman first. My old inexpensive bench has a thin top, but it had a skirt which allowed clamping of all manner of things to the skirt to make up for the weak vises (things like large panels, etc).

The groove in the bench underneath is 1 1/2 inches wide and similar depth (the top is 4 1/8" thick). It just under 2 inches from the front, obviously (just like the rail). The peak of on the stretcher is 1/2" high.

I don't prefer the type of vise that's sitting on top of the bench, i know that from experience. It's a small record copy (the one that LV sells), and I chose it to go on the end of the bench, which is something I use only for small work. That end of the bench is intended for things I found difficult making planes, and will have a row of dog holes from the end to the leg, right in the middle of the first board (right at the edge), specifically so that I can grip something the size of moulding plane or a small part right at the edge of the bench and use a plow plane or other fixtured plane without interference from the side of the bench. It's not the kind of thing that most people would want on their bench, but it's something I want.

I'd also like a non QR vise for that job, but I couldn't find anything of reasonable quality that would fit on what may turn out to be 14" of span from the back of the bench. The small vise only needs 11 inches of clearance or something, and most of the other designs that I saw were either too flimsy and with poor provisions for mounting, or too long. If it doesn't work out, it can always be changed.

I put the pin board above the stretcher on purpose. It'll be beech, the leg is ash 6" wide, and the screw determines the amount of force on the business end of the vise. To the extent that the leverage would've been better and the adjustment finer with the pin board along the floor, that's true. The holes in the pin board will be staggered in three rows, one inch apart in each row to make up for the shortened distance (vs. a board with two rows spaced a 1/2 inch). I've got a perfect pin for the bench - a crown burnisher, something I've been waiting to find a use for because it certainly isn't any good as a burnisher. Since the legs are hardwood, I think it'll work fine.

Time will tell, though. My habits are made already for another bench, it will take some time to get used to using something different.