New WoodChat!
Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

REAL MILK PAINT

Shellac Question

Posts

Re: Shellac Question

#26

Re: recipe for simulated garnet

Mark Mandell - Gone Round In New Jersey

16 oz of shellac (super blond fresh mix or SealCoat)

Colors to use: 1-Medium brown, 2-Dark walnut, 3-Honey amber, 4-Red mahogony

start with 2 drops #1, 1 drop #2, 1 drop #3

If you want to warm the tome, add 1 drop #4

For a brighter tone, delete #2

On this I used 2#1 and 1 each 3 & 4



the sapwood was taped off and then the mask "line" was erased with alcohol and a cloth

Test on scrap to find the tone you want. As you know, walnut can vary widely in color, even from the same tree. This is a quick and easy method to harmonize different parts of a piece. Just be careful if you're going to top-coat with waterbornes. A too heavy (too old) coat of shellac will cold check under a waterborne product DAMHIKT

Re: Shellac Question

#27

Re: Shellac Question *LINK*

wilbur

Here’s a write up on my experience using Everclear to deal with shellac flakes that left a gummy clump when dissolved.

As it turned out, after I had written this up, I left the shellac sit for a while longer. Eventually the gummy stuff went into solution. I used it on other projects, and it worked just fine.


Using Everclear to salvage old shellac flakes

Re: Shellac Question

#28

Jesper, Denmark

Re: Shellac Question

Jesper, Denmark

Bill, the most likely problem is too high a water content in the alcohol. As you will know, distilling past 95% is impossible without some co-solvent.

Bioethanol intended as fuel for either alcohol stoves or motor fuel usually have been either chemically dried or distilled with some isopropanol to reduce the water content to less than 1%. Ditto for carburator de-icing fluid.

This works better than the "regular" denatured alcohol, which may have up to 10% water.

Ethanol/isopropanol denatured with a little MEK is perfect.

Re: Shellac Question

#29

Re: recipe for simulated garnet

TomD

Thanks for the recipe. I use StuMac vintage amber, to warm up dead finishes like Varathane water based, or to unify wood tones, or to warm up dead wood like birch ply. It gives me what I need in one bottle, but it would be great to be able to tune it.

http://www.stewmac.com/Materials_and_Supplies/Finishing_Supplies/Colors_and_Tints_and_Stains/ColorTone_Liquid_Stains.html

Re: Shellac Question

#30

Re: recipe for simulated garnet

TomD

= honey amber in Transtint.

Re: Shellac Question

#31

Tuning It

Mark Mandell - Gone Round In New Jersey

Got started down this road after a cherry piece on which I had used garnet shellac under Target PSL cold checked and had to be stripped and refinished. I thought it was Target's fault until I called Jeff Weiss (the Target pres.) to complain. He explained the problem that all the manufacturers were having. Any shellac had to be fresh and sparingly applied to prevent the problem. Then, in conversation with Jeff Jewitt, he suggested toning the shellac sealer/tie coat rather than applying stain to the raw wood surface. The ability to very precisely control the tone with just the barest gentle mist from the gun was exactly what I needed.

Re: Shellac Question

#32

Oops, Forgot

Mark Mandell - Gone Round In New Jersey

For toning I use a one pound cut. Makes it easier to blend out any lap marks, especially if you're hand-applying.

Re: Shellac Question

#33

Thanks for tips

Bill Tindall, E.Tn.

The dye is not cheap so some guidance on where to start saves $$ experimenting with what gets tot he right color.

Re: Shellac Question

#34

nothing magic about Moonshine

Bill Tindall, E.Tn.

At best it will be 95% ethanol, the azeotrope of water and ethanol, plus small amounts of other alcohols which I would think will be too small to affect solvent properties.

The only stuff made here now days is Meth.

Re: Shellac Question

#35

Darrell in Oakville

Re: Shellac Question

Darrell in Oakville

I mix my own shellac, and yes, it gels in the jar without sufficient agitation, unless you are making a very light cut.

The solution to the dissolution problem is a magnetic stirrer. Google up a DIY magnetic stirrer and rummage through some piles of tech junk and you will no longer suffer gel-like shellac.

I made my stirrer from an old floppy disk drive, the stirrer bar is a rod magnet from Lee Valley. I also picked up a Melitta shellac grinder at a yard sale. Silly people were using it to grind coffee of all things. Ground flakes, mixed overnight makes for no gel in the morning.

Darrell


img

Re: Shellac Question

#36

Re: Shellac Question

Rum

FYI, you can also get used industrial stir plates for small money off of ebay.

The price starts to approach the cost of parts if you need to buy the pwm controller for the fan speed.

Re: Shellac Question

#37

mine is different

Bill Tindall, E.Tn.

Do I need to send you some to demonstrate that old shellac can form insoluble gels is various mixes of methanol, ethanol, isopropanol and water (variables tried) even when stirred for days on a surplus lab magnetic stirrer, warmed or not? Exposure of the shellac to moisture is not the cause of gels because my stuff has been stored in a lab dessicator over Dryrite.

For curiosity I am going to try some esters and ketones and methylene chloride. If nothing dissolves the gels it is proof that the shellac has polymerized into a cross linked polymer.

Re: Shellac Question

#38

Re: mine is different

Mark Mandell - Gone Round In New Jersey

Had a pound of Dark Garnet stored in a dark, air-tight container for several years. Only about half of it would dissolve. Tried different solvents, alcohols, acetone, lacquer thinner, all to no avail.

Lemmie know how you make out. I just pitched the mess.