New WoodChat!
Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

A55 Smoothing Plane

Chisels done

Posts

Chisels done

#1

Chisels done

CJ in MPLS

I finally finished the chisel handle project and have the entire set all sharpened. Note matching exactly, but all useful. The chisels are all Zenith brand chisels from Marshall Wells Hardware out of Duluth. The state connection was one reason to start purchasing them I guess.

I've got sizes from 2" down to about 3/16". Most of the new handles are maple and the 2" is, I believe, mahogany as a suitably sized chunk was ready to hand. A couple of original red oak handles were retained and the little chisel has what appears to be an ebony handle. All of the handles have a 1/2" post at their butt end that has leather washers glued thereon.

As an aside, I took the holiday as an opportunity clean up a bit and to flatten my bench top and reoil it. Note to all: Watco takes a while to cure at these lower temps and it is inadvisable to get sharpening dust all over the newly oiled surface. Fame to shame in about 10 minutes.

CJ


Re: Chisels done

#2

Re: Chisels done

Bill Houghton, Sebastopol, CA

"...it is inadvisable to get sharpening dust all over the newly oiled surface. Fame to shame in about 10 minutes."

No, no, that will provide some "tooth" on the surface so stuff doesn't slide all around. Just keep telling yourself that.

Nice work on the chisels. A very comprehensive set, and the local (well, moderately local) connection is indeed nice. I watch out for Stiletto tools (headquartered in San Francisco in the 19th/early 20th century) for the same reason.

Re: Chisels done

#3

Ellis Walentine

Nice work on all

Ellis Walentine

I'll bet those chisels are sweet. You were fortunate to find every size, Now you need a nice way to store or display them.

One word about Watco.... It isn't meant to be left to cure; you need to let it penetrate for a little while and then wipe off the excess. That's always been my biggest gripe with "Danish oil" finishes. They're thin to begin with, and they don't cure, so you end up throwing most of it away when you wipe it off. They sure are easy, though, and they leave a bit of protection and a nice "in the wood" look and feel.

Nice looking bench, too. You look like you're ready for some serious woodworking now. If you don't get distracted by that nifty dartboard. :)

Cheers,

Ellis

Re: Chisels done

#4

Speaking of the dartboard

Bill Houghton, Sebastopol, CA

I sure hope that window is tempered, or that you and your dartmates are good enough not to throw wild and hit the window!

Re: Chisels done

#5

Re: Chisels done

roger lance

CJ.....nice job on the chisels.....and you have a very interesting bench there as well. I'd like to see more of that bench and your shop also. Please post more. Thxs.

Re: Chisels done

#6

Re: Speaking of the dartboard

CJ in MPLS

Plastic tips and little interest protect the window. ;)

Re: Chisels done

#7

Re: Danish oil

TomD

You need to wipe them away, the largest part of the trade off being that they work in a dusty environment. Also, they are easily repaired and do not sit on the surface.

Did you mean Ellis, to say that they didn't cure. I thought they most assuredly did cure, by polymerization. Cure is more a phrase that I would use about a catalysed or two part finish, but I think it applies to anything that hardens off solid. Or if not, then I have lost your meaning as the objection would apply to other materials like lacquer or varnish, that do not cure under the second definition.

Words aside they do turn solid, dry, and edible in some cases.

Re: Chisels done

#8

Re: Danish oil

TomD

OK the main board has a better description of cured, Something Bill wrote. In that case maybe I could have directly said that most of these "oils" include the base component of varnishes, and therefore cure accordingly.