New WoodChat!
Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

THE WOODRAT IS BACK!

Sawing a perfect tenon

Posts

Re: Sawing a perfect tenon

#26

A practical consideration on good enough

Bill Tindall, E.Tn.

There is another fit factor. M&T joints are often used for things that are cumbersome to test fit. When making a table, for example, imagine the hands needed to do a test assembly if many joints were too loose to hold themselves together as the parts were assembled.

Strength considerations aside, I go nuts working with a M&T joint that doesn't hold itself together. So many times one needs to assemble these joints in order to obtain/fit some other component. It is so handy to be able to dry fit a table on the bench and measure stretchers and the like off the dry fit assembly, without it wiggling with a loose joint here or there.

But, your point is well taken. I may fret loose M&T''s so much that I rule out possibilities. There is no doubt that it takes longer for me to whittle a tenon on a table saw ( I seldom use a tenon jig) than to simply hand saw it, if I could to my satisfaction. (I could describe whittling a tenon on a table saw off line if anyone is interested. It is a dandy way to make a few if you can't reliably hand saw or its too much trouble setting up a jig.

Re: Sawing a perfect tenon

#27

Re: A practical consideration on good enough

Kees

Drawboring and drawbore pins is the answer to that. ;)

Re: Sawing a perfect tenon

#28

Re: A hack's opinion

david weaver

I may not quite be a hack, but I am by no means accomplished.

Lately I've had to cut a bunch of small mortise and tenon joints by hand. I have no idea how to cut them any other way than by hand.

I saw warren's comments a while ago to "not be afraid of your mistakes" and though I've waffled back and forth between cutting them on the mark in the past and cutting them fat, I have cut all of these on the mark. Some have been very slightly loose in the mortise, but not of the type that they'd clank around.

My time cutting the joints has decreased considerably. On the off chance that a tenon is still a bit fat (and by that I mean it won't quite go in or it takes too much resistance), I keep a bed float on the bench, and adjust it literally in about as much time as it takes to put a piece in the vise and take it back out.

It is a far nicer process than cutting a tenon fat and then trimming it to the mark, some of them fit fine right off of the saw. The random one here or there that is a bit loose will never be noticed once glue is applied. The largest error I usually have over the target mark (as in a fat part of the tenon) is about a hundredth and for whatever reason, they have erred just a bit fat. If they erred a hundredth thin, I doubt it would matter much in joint strength, but if it did, I could repair said problem joint at a later date, because i'm using hide glue.

I have no interest in ever cutting a tenon fat on purpose again.

Re: Sawing a perfect tenon

#29

Re: Or...

TomD

They could try both, which one does by sawing every tenon one can saw with the hand saw freehand, then if it fails to please, pull out the plane, router table, table saw, etc... to kiss the cheeks so that they do conform. I think the extremist idea that one is either perfect (but only at the cost of extravagant practice), or one should never try at all, is kinda odd. And one should saw everything else that one can by hand also, the more one practices the better one gets.

I think another thought to consider is that a lot of the angst comes from the idea one needs perfect cheeks, while a lot of better uses of the tenon require that the ends be engaged, not the idea that the faces be perfect, while the ends often rattle away. Both approaches will be called for, but certainly the ones requiring the ends to engage will not be as demanding in the sawing, particularly if wedges or pegs are in service..

Re: Sawing a perfect tenon

#30

I've been nudged

Bill Tindall, E.Tn.

Your experience mirrors mine on dovetails. After a dovetail pin cutting absence I tend to cut fat, then I hone in on just right, get a thin one or two and then it becomes reliably good (presuming I have a case and several drawers that provide enough cutting to travel this relearning path). But this relearning is less an issue with dovetailing a box or drawer with its redundant mating surfaces than a table leg or door frame where every M&T is critical.

I have 8 tenons to make for two Spice Box doors. The frame is delicate so these will be the easiest possible tenons to saw, ie small ones. I have ample cut-offs for trial. We will see how it goes.

Power tool tenon production is no piece of cake either. Setting up a machine to achieve the required accuracy is difficult and even once set up getting precision tenons is not certain due to tiny differences in stock thickness, clamp pressure, phase of moon, and I don't know what all. I just find it a difficult joint to reliably execute by any means I have at my disposal and I refuse to spend the price of a good used table saw for a Domino. (I am told they are reliable, though anything that makes wood go away quickly is less reliable in my hands)

That said, "not be afraid of your mistakes" is not always advice that is practical to follow. In the case of my door frame the frame pieces are one of a kind matched rift walnut. Screw one up and I need to find another board to extract 4 new matched frame pieces with attractive flowing grain to match the line and berry that will lie within. This reality drives me to proceed by the least risky route to success.

Re: Sawing a perfect tenon

#31

Re: Lies and "So whats"

TomD

"Most weekend warriors will benefit from the use of a jig. The real question should be: Why is there the sense of cheating when one uses a jig? I submit it is a bit of real men don't ... and the fact that we are all exposed to those who just grab any old saw, walk up to a board and split the lines. We feel diminished. Well, compared to them, we weekend warriors are diminished. Get over it. Use the jig or keep gluing shims on."

I think the cheating part mostly comes up in claims. If you want to say you did it all by hand, implying you are the line splitting guy, but you are in fact the jig it at all costs guy, then the "you" in the example is lying about it. Same deal as the fact that Edmund Hilary didn't climb Everest, not by any reasonable definition. It isn't his fault (resoundingly regarded as a great guy) that the idea stuck. People who climb it in even less convincing style as is now common, have done something of note, and have something to proclaim, they just shouldn't say they climbed Everest. Of course like any mater of usage, this is a correct usage of the words so calling it 'lying' might be unfair. Delusional, closer to the point. But environmental or other similar objections aside, you can helicopter to the top of Everest, for all I care, it isn't cheating unless you claim you climbed it using your legs.

Another place it gets dicey is the part of the argument that deals with difficulty. There are two sides as always, and the side that thinks it is easy, at some level, can feel the person with the jig is cheating themselves. It isn't real cheating involving compromised honor, but they perceive that the person using the jig would rather be the person cutting to the line, but wont cut the apron strings. So to speak. There are areas like guitar building where jigs are the rule. They would use a jig for every single stage of the build. In fact there is a glory to be found in the making of the jigs. But if you are the guy who wants to be hands on, but won't even try, then you could be cheating yourself.

Which brings me to the "so what". My reaction to the jig was "so what" like telling me I could use bow on a rectangular parcel, as well as cubic one. I would say that I am little sceptical that it works all that well, and can think of several ways to improve it. But so what, designing jigs ought to be like breathing air who really needs to be told. Of course why not share it and well done Derek, there are many articles on jigs, and Derek has generously shared it here (and there) first. But that was my honest reaction. There is this idea that jigs are some kind of kludge of the unskilled and that hand skills can be elevated to a high degree. But jiggery can also be elevated, there are many people who can figure out a clever jig per breath. So it would be unfair to leave it unsaid. "so what".

This is probably a machine, and not a jig, but you have to admire this thing. Now a hand saw powered version would be fun:

http://www.youtube.com/watch?v=h-pdUWoNjPo

Re: Sawing a perfect tenon

#32

Re: I've been nudged

david weaver

It's pretty easy to contract on looseness when there is a critical item that can't be ruined. I'd probably be cautious about the shoulders on those boards and give them an extra check to make sure I'd have no gaps, but I'm pretty care free on the tenons.

The only machine I've ever had good experience with on making tight tenons and doing it in a manner that is traditional is a multirouter. I really haven't tried much else out, but the multirouter works on templates and getting things in a machine correctly, and I hate worrying about that. If something is messed up, cuts end up in the wrong place and the result is a problem. It'd be a better thing to use when templates were made for a batch of various things and you wanted to be able to do 8 of the same thing fast.

As far as taking what I consider to be the lazy way for someone without much in terms of serious skill (sawing right to the line), I figure if I ever cut one that's absolutely terrible, I'll use epoxy or shim the joint. Not caring about a mortise that's a little loose here or there is also an item of curiosity - seeing if one ever actually does fail. If I have one that's structurally critical, I probably will still struggle to allow myself to be free and easy with it.

I have one improvement that I'd like to make yet, and that is to saw tenons entirely straight up and down without going from both sides, if you know what I mean. I know a mechanic does that, saws to the line all from one side. I'd like to be a mechanic someday.

Re: Sawing a perfect tenon

#33

Re: This data is simalar to some other

TomD

Breaking strength data is meaningless. No real use of furniture involves attempting to break it. All thought should be put into situations with millions of cycles to failure, with brownie points for repairability.

80% strength is certainly worth noting, but irrelevant. Climbing rope knots run in 65%-80% range and the safety factor (worst case rarely approached) is around 4-1 safety factor. Much furniture in a breaking strength test, might be 10-1, or 200-1, no idea. But the load when pulling out a silver drawer is much less than the load required to break that drawer in the line of the load path (ripping the front off). (breaking tests often use load paths that only occur when trying to consolidate furniture for the dump such as corner to corner loads). So the margin of strength of one glue over another in a destructive test is probably beside the point, though a benefit where all else is equal, which it won't be.

Re: Sawing a perfect tenon

#34

Re: Might just as well use the tablesaw.  Well...

TomD

The table saw is limited to short pieces, even the bandsaw is limited to lengths one can control. One can often get longer pieces on the jointer. Then there are people who own the hand saws, and not the TS. In the latter group are some of the classical musical instrument makers who work entirely by hand, but jigged some functions to take away any stress; make easier for hacks in the shop (training issue); ensure you never loose a piece, ever. It is more fun to hand bend pieces, and more versatile, but some of those guitar sides cost 1K or more. So you can't really afford to loose even one set. Cabinetmakers oftne work with cheap wood, and the joints go in before a lot else has been done. Not the case with everything. For instance, and analogous set-up is cutting frets. I can do it freehand, and the guitar is oftne nearly finished at that point, but one of the "advances" was to make it so the slots went in before any serious work was done, and in fact the neck was a separate piece. The fingerboards are ebony, as it happens.

Here is a neck jig. I think some guy used it so he wouldn't have to learn how to saw, but it comes from a Euro tradition, I believe.


Another shot of the thing.:


I'm a real nutbar, I mostly work by hand, and am proud of that, but when I see a cool jig... I want it!

Originals of these jigs, or probably these actual jigs, are by Geza Burghardt.

Re: Sawing a perfect tenon

#35

Re: P T's suck also... & the ashcan of credibility

TomD

"But in the case of the M&T joint there is no redundancy to compensate for lack of accuracy of the fit."

Leaving aside multi tenon joints, or depending on definition, finger joints... However, there certainly is plenty of redundancy in the joint. People whale on those things for centuries, and they hold up. It really doesn't mater what is the source of the overbuild, whether it is multiples or size, etc...

"A loose fit degrades the joint strength. Any glue formulated with water will be poor at gap filling and that includes hide glue. When the water goes away holes remain and the glue becomes a foam rather than a coherent tough film."

Of course wood is also a foam, when the water goes away, by your definition, and in many cases it is less strong, at least along the grain lines, than glues, so this may be one of those ideas that sound well thought out, only at first glance.

"For various reasons I have measured tenons I have made and concluded that the tolerance for a good joint is one where the tenon is in the range of 0 to 0.005" thinner than the mortise. One may quibble with this exact number but the conclusion is that the difference between a joint that is difficult/impossible to assemble and one that is too loose is a small number of inches, something on the order of a scribe line width or less."

I would probably describe it pretty much as you do, and yet for hundreds of years people have been making it work. Something we are not accounting for is at work, and i have to say, a lot of the fits on stuff like the NYW are way too loose for me, but somehow the work gets done between that and a few thou. I think your 5 thou claim probably wouldn't hold up in testing, because it rarely does in machine work either. Machine work can go to 11, as the saying goes, but it is actually pretty tough to measure south of 1thou without some really fancy gear, which power tools aren't.

"Hence, the challenge of sawing a mortise is to make two saw cuts with sufficient accuracy to yield a tenon that is accurate to some small number of inches ( about 0.005"). And, if you are going to claim that hand sawing is practical this tolerance needs to be achieved without post adjusting of the thickness by plane or chisel."

I think you are right that it would help if the joinery could come off the saw, however, if it required some fitting, it is still practical so long as the fitting is as efficient as other alternatives. Rarely is power cut stuff right the first time either. It can be set up to do repeats, but one-off work is rarely of that type. This is why we have biscuits and dominos, the power tools suck at this also

"Now the question: For someone that builds a piece or two of furniture a year that requires M&T joints, is it reasonable to expect that this person can reliably saw a M&T joint?"

At the low end of that, no. If they are five years in the craft and have never practised a lick, and have only made several small pieces, ten total. But I am not expecting that much from them no mater how you slice it. If they did ten highboys, or guitars and really worked at it, why not. Can you learn to play the guitar in five years?

"Yet, when I start a new piece, after maybe several months of not sawing dovetails, some of the first few pins are not up to the accuracy required for a strong M&T joint."

I think this can be relieved a lot by simply doing some practice cutting, even just a half dozen kerfs, first.

I also think this analysis fails because it seems to imply there is dovetail sawing, and tenon sawing. Not really. Sure you can learn on only one thing, and only be good at that. But then you don't know how to saw. When you know how to saw, it is all pretty much the same, so you should be able to do the tenons also. I remember watching Norm do some hand sawing. Normally his hand work was terribly amateur, but when it came to sawing, he looked like a pro. When he started hand saws were still in use on the jobsites I know. So maybe hacking away a 2X with a hand saw made him a good sawyer, in general, worked for me.

Now do people want to learn to saw? Judging by the tool catalogs they seem to want to. And to boot, a few newbies went successfully into making saws, the filing of which is very much like hand sawing, and some of these guys had very low hours in the air, and turned out great products

"The task of learning and maintaining the skill to hand saw tenons seems too daunting to attempt. Many seem to have come to the same conclusion for I know of no one that routinely saws this joint. If driven to, they expect to adjust thickness after sawing to get the perfect fit."

Got me there. I routinely saw some, but on furniture, a small piece often after counting reveals say, 36 M&Ts. I reach for the fastest method I can find.

"I am skeptical that hand sawing a M&T joint is practical for the typical furniture builder. Agree, disagree, whatever?"

"Practical" as usual just means you don't think so, which is why I knew you weren't a bowhunter, and in particular a stickbow guy. The sale of bows would indicate otherwise, and in this case maybe the sale of saws. Better get practising, because if DTs are anything to go by... I was a hero in the 90s, and now my DT skills are just run of the mill. I'm probably better than I was... Get sawing or prepare for the ashcan of woodworking credibility. I'm OK with the ashcan, but I know it is coming.