New WoodChat!
Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Fast and affordable laser cutting – so you can make the parts you can’t find anywhere else

Woodworking was supposed to be relaxing

Posts

Woodworking was supposed to be relaxing

#1

Woodworking was supposed to be relaxing

Tony Wilkins

But every time I ask a question or look for encouragement it comes down to contention. My woodworking tools will be on ebay soon.

Re: Woodworking was supposed to be relaxing

#2

Well, if you can't stand the heat.....

roger lance

good-bye Tony......I'll remember you as a guy who was often given the advice to get into the shop and practice.....make something.....anything.....get some experience.....build some skills.....observe that the word "working" is a major part of "woodworking".....but you never seemed to follow that direction.....good luck to you in whatever activity you next choose to read about.

Re: Woodworking was supposed to be relaxing

#3

Just cut some dovetails.

Chuck Nickerson

My brain sort of worked like yours. I feel your pain. But just cut some dovetails.

Re: Woodworking was supposed to be relaxing

#4

Re: Woodworking was supposed to be relaxing

North of the Border

Either that (quit traditional woodworking, no one says hand tool work is easy), or try working with power tools (if you haven't gone down that path). OR, drop woodworking as you are planning to.

Some make good workers by self-teaching and you seem to be saying you aren't one of them. Then learn the skills by attending classes where skilled and experienced instructors help with your skill building.

Books, DVDs, forums, classes, etc. are no substitutes for hands-on practice. If you don't want to practice or can't afford the time for practice, woodworking is not the right hobby for you, just like golfing is not for a lot of other people.

Re: Woodworking was supposed to be relaxing

#5

It sounded like you were doing OK

Wiley Horne--So. Calif.

on your initial saw cuts. What happened? You've come a long way to give up at this point. it would be a shame. Sleep on it for a couple days to think it over.

Wiley

Re: Woodworking was supposed to be relaxing

#6

NOOOOOOOO!

Tony - Memphis

Don't do it! The pleasure you'll get will far outweigh the rest!

I'm not sure exactly what you are referring to as I haven't followed the whole thread.

Woodworking is good therapy...we all need it it, so don't give up because of OTHER folks think or say.

Now, on to making dovetails....I read everything I could get my hands on, wathed videos, etc. etc. Made notes of some tips and then went out and got started practicing. I forgot who said it, but dovetails are realy learnign to cut to a line and good chiseling techniques. I sometimes spend 20 or 30 minutes just marking the end of a board with angled lines and trying to cut to the line. Then I cut that end off and start again.

Don't get too caught up in the layout, angles, etc. Use decent wood too. I practiced on pine and I couldn't work that as well as I did poplar and mahogany. The wood species matters too how close to the line (liek I can really cut close to a line on command - ha!). Phil Low taught us in a class when using pine for the sides to cut them a little fat because pine will compress a little and perhaps make a tighter fit - worked for me with walnut fronts.

After you cut some, examine the results and teh cause of any imperfections...sawn to the baseline? Past the baseline? Did I leave the pencil/knife lines? Check to make sure your tail cuts are perpendicular to the face. Etc. My biggest issue is (notice I didn't say was) keeping the saw square to the face when cutting the tails (i do tails first) and sawing to the marked line n the pins because I sm still not good with a saw.

Hang in there! Find Chris Schwarz post about practicing dovetails. I think he did some every night for a month. Also, I think there was an article in FWW about common issues and a suggestion to warm up each dovetailing with a 5 minute dovetail -Gart Rogwoski (spell?).

Tony

Re: Woodworking was supposed to be relaxing

#7

Sniffing dogs . . .

CJ in MPLS

Do what you will, but keep in mind that the analogy of dogs sniffing one another's rear ends is pretty much par for the course in any knowledge intensive field/hobby/endeavor and doubly so for woodworking.

It is frustrating, but can be darned funny as well. I may have related this story here before, but since my wife still mentions the "dog sniffing" story from time to time to much amusement, it still has currency I think.

Back when I was still in the acquisition stage of woodworking, I wanted a no. 18 Stanley block plane. I found one at a local tool shop and arranged to go pick it up. When I arrived, incidentally with my wife in tow, there were a few fellows chatting with the proprietor. I identified myself as the guy who was interested in the no. 18, but instead of simply bringing out the plane and taking my money, what ensued was a rather thorough, but not entirely unexpected, vetting of my bona fides.

"What was I going to use if for?"

"Why would you want to do that?"

"Wouldn't it be better to use this other tool that has these cool features that only the truly initiated would know about?"

I'm clearly taking a bit of liberty with the facts here, but not too much. In any case, when we got to the car, no. 18 in hand, my wife whooped with laughter and told me that we woodworkers had looked like "so many dogs sniffing each other's asses!"

Of course my pride was stung, both by the impromptu cross examination and the not so delicate characterization, but I've come to find humor and entertainment in both of these.

This website and its users, including myself, definitely exhibit some sniffing type behavior. Embrace it as it's half the fun. Just don't let your wife see what is going on or you'll never live it down. ;)

CJ

Re: Woodworking was supposed to be relaxing

#8

It is relaxing...

John in NM

It's internet forums that aren't! :D

Seriously though, you aren't causing the contention, just finding out that 1.) there's more than one way to do just about anything, and 2.) most of us are very attached to our own particular way.

The only reason to dump the hobby and sell your tools is if the practice of it isn't relaxing for you. Don't worry a bit about what people who hang around on internet forums say.

Re: Woodworking was supposed to be relaxing

#9

Re: Woodworking was supposed to be relaxing

Derek Cohen (in Perth, Australia)

Hi Tony

You must have been having a bad day to come up with this. Regardless of the rowdiness of the forum, it is just a bunch of cyber friends debating, showing off, and helping out. I thought that the thread was really rooting for you. I imagine that it was not that easy in the shop - we all have days like that .... wanting it to go well .. and then it doesn't. Sometimes I'm just tired and my reflexes are not there. I've learned to walk away. Come back another time. Woodworking is wonderfully relaxing when you are working within yourself, but it can be awfully stressful if you are challenging yourself to learn something new and difficult.

With all techniques, including dovetailing, there are skills to develop first to feel you are working within yourself: in the curent circumstances, marking accurately, and then sawing to a line.

Put aside the drawer until you have practiced these and feel that you are comfortable with each. Don't even do the chiseling at this stage. Cut off the end and start again. Do this for a week, and only then add in the chiseling. There are tricks there to ensure the baseline is saved - but that is for another day. One thing at a time.

Regards from Perth

Derek

Re: Woodworking was supposed to be relaxing

#10

Re: Woodworking was supposed to be relaxing

Guillaume Dery

Hey Tony,

I lurk a lot more than post here and am nowhere as accomplished as a lot of the guys here.

However, I need to take a few minutes out here to take exception to your post. Woodworking is relaxing. It is also stressful, for me, specially so at glue-up and finishing. However, it seems to me that you are confusing the cerebral aspect and the activity itself. Judging from your references to many books and from the questions you posed when you first jumped on ths forum and the progression or lack thereof, you seem to be stuck at the analysis paralysis stage. You spend way too much time reading, researching and not enough time doing.

The folks here have always answered your questions nicely and with encouragement, albeit with differences of opinions. Ways to skin a cat and all that.

Now I'm truly sorry but I am not going to be quite as nice as everyone who answered this thread. A few points for your consideration:

1. You have tools that are too good for you. I don't mean to be derogatory here but based on my recollection of some of your previous posts, you have some real best of breed stuff in your acquisitions. However as a rank beginner, you haven't developed enough of a relationship with the basic tool forms to understand and appreciate the nuances that make the difference between run of the mill and excellent. I suggest you develop your skillset to be worthy of your tools.

Don't get me wrong. That is a failing of the modern connected society and the blogosphere. You have too much info at your disposal. Many newbies to the craft buy way more tool than they need because they hear it's the best Truth is that stellar pieces have been made with much more rudimentary tools than you have. Stop buying and start using.

2. I don't know if its due to too much book learning and online consultation but there seems to be an impatience for results without putting in the time. All must pay their dues. Perfect intellectual understanding of a process will mean crap for execution until you develop the hand-eye coordination, muscle memory and technique. Stop asking and start doing.

3. Unlike machines which can be mastered, or at least set to achieve precise repeatable results in very short order (anyone with 1/2 a brain and decent motor skills can turn out adequate results on any given machine in less than 1/2 a day), hand tools take a very long time to master and no 2 tools or 2 users are exactly alike. The path to mastery is long and will lead to different techniques for different people which they will tend to defend to the death because A)it works for them; and B) they invested much blood, sweat and tears to get there. The point of this is until you start mastering your tools, these answers are guidelines only because you don't know what works for you. Again, stop asking and start doing then come back with questions when you have a point of reference.

4. Don't jump into show joinery (dovetails, through mortise & tenon, etc) until you have some basic mastery of your tools. Achieve that by practice. Spend a week or 2 on sawing exercises. On a scrap board, draw a baseline and try to cut 20 or so parralel and square lines down to the baseline. Check your work with a square, note the defficiencies and cut them off and try again. Do this until you develop a feel for when you are cutting straight and true. Then introduce scribed lines and teach yourself to saw to a line (straight). Get good enough at that, then introduce sawing at an angle as in for dovetails. For planes, do the six square block exercise until you are dead on. Same principle applies to chisels, be it for paring or mortising. Get your basic skills up to snuff through practice, These will be the building blocks for all future fine woodworking you will do.

I'm sorry if this is a bit long-winded and harsh but to be honest your post struck me as somewhat petulant and just rubbed me the wrong way. The bottom line is that the fine folks on this forum have been very giving of their time and advice and you should be thankful for this. You also need to stop thinking so much and start doing more.

My opinion, freely given and probably worth exactly what you paid for it.

Guillaume

PS: This was not meant to discourage you but to kick you in the pants to actually do more woodworking rather than wood-thinking

Re: Woodworking was supposed to be relaxing

#11

Very, very well said.

Wiley Horne--So. Calif.

" I've learned to walk away. Come back another time. Woodworking is wonderfully relaxing when you are working within yourself, but it can be awfully stressful if you are challenging yourself to learn something new and difficult."

In the same vein, something I've learned the hard way more than once is to instantly drop it and walk away when you make a mistake--especially an egregious or right-at-the-last-minute mistake--that snatches defeat from the jaws of victory. Don't try a rescue when you're insanely pissed. It's like Derek says, just freaking walk off and let it all slide off your shoulders. You'll think of a solution later, maybe better than what you were doing. Or have the wherewithal to just start over.

And never mind the internet crazy. We can't help it. Hope to see many more Tony posts as we go on.

Wiley

Re: Woodworking was supposed to be relaxing

#12

The best revenge is to make them jealous

Patrick Gibbons

In the end, only your experience matters.

Re: Woodworking was supposed to be relaxing

#13

Thanks for all the responses and support

Tony Wilkins

Long story short - irritation over another issue got my anger/PTSD going which lead to me going out to the shop in the wrong frame of mind which lead to me being overly aggressive and underly careful with my chisel which lead to me moving the baseline back on my tail board which lead to the pity party above.

That said, I would have retraced my steps earlier if the first post wasn't Roger's that made things frankly worse.

I'll take contention with the contentious post above ;) I don't think it was not nice nor contentious:

"1. You have tools that are too good for you. I don't mean to be derogatory here but based on my recollection of some of your previous posts, you have some real best of breed stuff in your acquisitions. However as a rank beginner, you haven't developed enough of a relationship with the basic tool forms to understand and appreciate the nuances that make the difference between run of the mill and excellent. I suggest you develop your skillset to be worthy of your tools."

I did buy the best tools and no I don't think they will make me better. I also have some vintage and not greatest tools. The plan was to develop the skill set and not have to worry about the tools.

"2. I don't know if its due to too much book learning and online consultation but there seems to be an impatience for results without putting in the time. All must pay their dues. Perfect intellectual understanding of a process will mean crap for execution until you develop the hand-eye coordination, muscle memory and technique. Stop asking and start doing."

That was what I was doing when I started the dovetail thread - doing. I figured it would be something others were familiar with. If I got helpful information so much the better. I did get some helpful information - probably too much. It soon got to the point where I was overloaded with info.

"3. Unlike machines which can be mastered, or at least set to achieve precise repeatable results in very short order (anyone with 1/2 a brain and decent motor skills can turn out adequate results on any given machine in less than 1/2 a day), hand tools take a very long time to master and no 2 tools or 2 users are exactly alike. The path to mastery is long and will lead to different techniques for different people which they will tend to defend to the death because A)it works for them; and B) they invested much blood, sweat and tears to get there. The point of this is until you start mastering your tools, these answers are guidelines only because you don't know what works for you. Again, stop asking and start doing then come back with questions when you have a point of reference."

No argument there.

"4. Don't jump into show joinery (dovetails, through mortise & tenon, etc) until you have some basic mastery of your tools. Achieve that by practice. Spend a week or 2 on sawing exercises. On a scrap board, draw a baseline and try to cut 20 or so parralel and square lines down to the baseline. Check your work with a square, note the defficiencies and cut them off and try again. Do this until you develop a feel for when you are cutting straight and true. Then introduce scribed lines and teach yourself to saw to a line (straight). Get good enough at that, then introduce sawing at an angle as in for dovetails. For planes, do the six square block exercise until you are dead on. Same principle applies to chisels, be it for paring or mortising. Get your basic skills up to snuff through practice, These will be the building blocks for all future fine woodworking you will do."

This is basically what I've been doing for the last two years.

Re: Woodworking was supposed to be relaxing

#14

Re: Woodworking was supposed to be relaxing

TomD

I think if you want encouragement, other that the buy a dog type answers, local clubs are a whole lot better than forums. Finding a good local neander type club could be a challenge. Wood turning clubs seem easier to find and are generally more positive.

I just do the stuff I do, and I don't care at all what other people do. I try not to answer posts unless I think there is something to add that will help other people, otherwise why bother. There isn't any positive feedback from answering posts, so an ego feed is pretty pointless, which is a good thing. I'm here to ensure nobody else gets it, and they return the favour.

I got into woodworking because I wanted stuff. I still do. I have an endless series of boats I want. I want an endless amount of other stuff too. Tooling, bikes... it varies from time to time. So I'm not stopping until I get to the point that the material world stops being attractive to me. Which should be a while yet. The point being that woodworking is about meeting needs in the real world. I need a certain number of dovetails, musical instruments, epoxy joints. I don't really need another argument over how to do those things. It just irks me if I think stuff is being overcomplicated, or whatever. But at the end of the day if you don't need the stuff woodworking is about why do it? Sure it is a hobby, but why would I choose to make a lot of beer if I didn't drink. I need some more pike and bass flies this summer. Gotta get er done. A few days back, I needed a tree out of my life, it's gone. Real needs. Makin it all about tools, would miss the point. If they don't get you stuff you need to do more stuff, what is it all about?

Re: Woodworking was supposed to be relaxing

#15

Re: Well, if you can't stand the heat.....

TomD

Man, that is cold. I don't know if it applies to our friend, but it sure is true to the scene.

Re: Woodworking was supposed to be relaxing

#16

Re: Don't make a religion out of stuff

TomD

I so often here people go on about how important something is to them, where they raise something like bowhunting to a religious level. Don't feel it has to be that big a deal. If you like woodworking do it: if not, don't feel trapped into it. it isn't supposed to be life-changing, it is something you do, like wash the dishes, or dusting.

Re: Woodworking was supposed to be relaxing

#17

Re: Thanks for all the responses and support

TomD

"I did buy the best tools and no I don't think they will make me better. I also have some vintage and not greatest tools. The plan was to develop the skill set and not have to worry about the tools."

That is an entirely valid approach. There are things that everyone benefits from equally and things that they don't. An accurate rifle is the same boost for every shooter. A formula 1 racer is probably beyond the ability of most drivers to do anything with. Granted the accuracy boost of the rifle might not be as effective a means to improved score and practice, for a beginner, but I never suffered for having one. A straight rule that cost a lot of money will never hold back your woodworking, unless you think it is a magic cure for something, or an end in itself.

If you decide to go down some rathole like the one western woodworkers have evolved out of Japanese tools, you had better be prepared for the idea that it might be like learning to skateboard while juggling, but as long as you know what you are getting into, there are probably a lot of people who have followed that path.

There was an article in the paper this week about how we might be further than we hear we are from artificial intelligence, because... We don't even know what intelligence is, so making an artificial version is a big ask. That applies to some of the tool stuff. The increments some are after are real, but they are difficult to even express in words, or difficult to pin down to a necessary capability, so if you get off on those tangents, expect some lost time, however fascinating.

But overall, good tools are better.

"That was what I was doing when I started the dovetail thread - doing. I figured it would be something others were familiar with. If I got helpful information so much the better. I did get some helpful information - probably too much. It soon got to the point where I was overloaded with info.'

One also has to be careful of the idea that every tip is compatible with every other one. So if you took my idea on the pencil, and Derk's tape routine, they would not play well together, since my pencil wouldn't cut his tape. A comic example. But the point is super real. Often when you hear arguments that have to do with how to do stuff, the heat is there because someone had a breakthrough when they used a particular technique. But that technique may not be the key to your trajectory, or even the thing that really got the proponent his results. Sometimes it is just time. I suppose I could cut dovetails with every serious method proposed. It is woodworking you saw, plane and cut to a line. The process should be possible in all kinds of ways.

So maybe the tails first folks think they invented some kind of magic because they were told it wouldn't work, and it did. But seriously, if the only way out of jail was to cut the tails first, or the pins, or half of each with a third of the knees, I would get it done somehow.

"No argument there."

Well actually, there is certainty and risk in either category. Planes are certainty, axes are risk. Milling machines are certai... Ok bad example, and freehand grinding is risk (of both types). Most people who work in mixed tooling know the stuff like buffers are real hard to use. We sometimes forget that the world that we call machine is way more complex and came later than the easy chimp world of a couple of sticks with bits of steel wedged into them.

"This is basically what I've been doing for the last two years."

Good plan, and it was good advice. However... a lot of people just can't stop themselves being project driven, so join the party if you end up there. And while it is more sensible to separate practice from projects some of us know this for a fact because we made all the same mistakes most do.

Re: Woodworking was supposed to be relaxing

#18

Re: Don't make a religion out of stuff

Bruce Mack

Tony- there's not a thing I completed that I didn't like initially. That extends from gift boxes to feral cat shelters. I find that gifting, getting the object out of the house, helps. Truly, the nicest things I make now are no more worthy than the clunkers I made years ago....all were done with good intent. What you do, anything, enhances your life.

Re: Woodworking was supposed to be relaxing

#19

Re: A final thought

North of the border

After reading the comments many have offered, I think I should remind Tony that practice alone is no good, no matter how much time you spend on it. You MUST know the proper techniques in the first place to make practice useful. I have seen people practice sawing with frustrating results because they held their saws way too tight.

Forget about practicing until and unless you can find one who can show you how to do it -- in person. Books, DVDs, etc. will help only AFTER you have done it right live. Hence my earlier suggestion that you find someone experienced to guide you, e.g. in attending a workshop.

It is easy to say cut to the line, split the line and what not, but in reality, unless you have done it and got it right, frustrations are bound to come your way.

I have shown and taught a girl with zero sawing experience to saw straight in 5 minutes because I could show her in person and correct her mistakes as and when she made one. Now, will she cut straight after the lesson? It would all depend on whether she would keep practicing her learned skill.

You have the tools...you now need a warm body -- stay away from the cyberspace until you find an instructor -- to give you hands-on guidance. Not every woodworker is self-taught material.

Re: Woodworking was supposed to be relaxing

#20

Just my licks...

Bruce McCrory

Hey, I earned a dubious honor on a few lists. It comes with not giving a blank about what others say. Except, when they screw up. But mostly, it's me who does that.

I am a perfectionist. It is a disease, and many people share that affliction; so I am not alone. My affliction is particularly bad where no one sees results--design. When I have made myself so stinking sick of what I am designing, I walk away. Sometimes, for a whole few minutes.

Anyway, to crank the kite I am riding back to earth, and what I suggest others like me do, is go to a site like Mark Firley's at the Furniture Record

http://thefurniturerecord.wordpress.com/

and feast myopic eyes on the delightfully ugly joints that Mark is in love with. Look at those examples of furniture in the Twilight Zone. Just don't let him into your bedroom!

After a day of that--or, twenty images--you will love anything that you make, yourself.

Re: Woodworking was supposed to be relaxing

#21

Re: Woodworking was supposed to be relaxing

paul warnock

My response will probably be one of the non-sugar coated ones. I usually lurk here, checking things out now and then. I remember showing up at work one day (a long time ago) with a Stanley Bedrock #5 that i spent all weekend cleaning, truing and sharpening. My master took it from me and told me that when my skills were worthy of the tool he would give it back (which he did). My masters ( when I was an apprentice) were first generation Croatians. I learned to duck flying pieces of wood, learned to swear in Croatian and how to keep my mouth shut and listen. I wanted to learn these skills more than anything. I ate, drank and lived traditional wood working. No measuring plane shavings, or debating sharpenning methods. I was only allowed to clean the shop and sharpen tools for my first six months. Then I was allowed to make simple, little things. As a Journeyman, I worked in custom cabinet shops, re-fitting sailboats, building pipe organs, and making fake antique furniture. I bought Norris planes, fine boxwood handled chisels and all Starret measuring rules as I improved. I have taught (hopefully more kindly than I was taught) I have come to realize however, that most students lack one thing: PATIENCE. Everyone wants to make a highboy, carve a ball&claw foot or do inlays in the first week. To me, a piece of 24" wide Honduran Mahogany is very valuable. Not just in terms of money, but also the universe. Im not letting someone who has not mastered the basic skills "hack into it" with the hopes of making it into something.

I hope you develop patience both with your self and your hands. Woodworking can be quite rewarding (both mentally and spiritually) if you give yourself a chance. I love the Zen like state of passing a tool slowly across a sharpenning stone and it allows me to focus on the task ahead. Even if the finished piece looks like a drunk made it in some back alley, you have accomplished something. Note the flaws, and either give it away or burn it and move on to the next piece. With Practice and Patience you will improve. Without these, let me know where and when your tool sale will be.

Re: Woodworking was supposed to be relaxing

#22

Maybe the internet's not the way for you to learn

Bill Houghton, Sebastopol, CA

I learned my basic woodworking skills way back before the Internet. Some of them, I realized later, came from helping my father; many of them came from reading books from the library (and, later, when a little money appeared, from purchased books). A few of them from workshops at woodworking shows. The vast majority came from what I refer to, still, as frightening innocent pieces of wood: actual shop experience, which included times that I did something wrong and either had to scrap the project or think creatively about how to salvage it*.

The books, I found, contradicted each other; but I was reading one book at a time, and this may have led to a calmer atmosphere as I considered each author's arguments. Along the way, I discovered that there's more than one way to perform many procedures in woodworking.

As you've learned, the internet has tradeoffs: on the one hand, you can get all kinds of opinions and ideas for any given question. On the other hand, you can get all kinds of opinions and ideas...and it can get overwhelming when you're just starting out.

You might want to consider selecting a single author from among the respected authors** and following his/her advice while you get out in the shop and do the real learning, learning by doing. Come on back when you've got projects to show off (there's not nearly enough of that kind of post here!); and don't wait until your projects are "perfect." Beginning projects are just as perfect as the stuff Derek, Keith Newton, and others post, only in a different way. But don't log into the how-to conversations right now.

But if you find you don't learn well from books, North of the Border has a great suggestion, too: find someone to teach you. There are workshops galore around the country (all will be better than not learning), and many of the woodworking shows will have mini-workshops; or you may be lucky enough to have an active woodworking guild in your area that does workshops. Or maybe you're really, really lucky: maybe you have an older relative, a retired neighbor, a friend, or someone in your circle of life who'd like to spend time with you teaching the basic skills. Think about your possibilities.

Eventually, you'll have enough experience-based confidence that your head won't be spun around in a million directions by the conversations.

*Not that many years ago, I made my wife a tote for her pottery tools. I laid out the ends to slant up to the handle, starting above the sides; but I forgot that the sides have thickness, and the ends looked very awkward, dying into the inside face of the sides. I solved the problem by cutting oversized tapered pieces of stock and gluing them on, then fairing them into the sides and intended top point with ye goode olde hand plane. I can see the fix; my wife never noticed it.

**I say this, knowing that, if you ask "who's a respected author?", you'll get multiple responses. That's OK: they're all correct answers. Just pick one. Heck, put the names that come up in a hat, and pick one that way. They're just guides; as I said above, the real learning comes when you're applying tools to wood.

Re: Woodworking was supposed to be relaxing

#23

Adam of Oakland

Re: Maybe the internet's not the way for you to le

Adam of Oakland

a very well articulated response, Bill. I especially like how you describe a new person's experience with the contradictions: they're concurrent as one bounces around the internet, but much more serial when you're apprenticing, studying in school, or reading.

Re: Woodworking was supposed to be relaxing

#24

Re: Woodworking was supposed to be relaxing

TomD

"To me, a piece of 24" wide Honduran Mahogany is very valuable. Not just in terms of money, but also the universe. Im not letting someone who has not mastered the basic skills "hack into it" with the hopes of making it into something. "

I'm with you on that, so... I recommend staying off the lutherie sites, where some newbie with a router and some wood Tores probably never saw the like of in his career, is undertaking his first guitar, and it will probably play OK, and look like a masterpiece. But they gobble up the fancy boards like they are masters.