New WoodChat!
Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Portable Sawmill & Tree Service – Abingdon, VA

Post your picture here ....

Posts

Post your picture here ....

#1

Post your picture here ....

Derek Cohen (in Perth, Australia)

OK guys and gals, I've had enough - it is way overdue that we had some group involvement. What is going on? It is so quiet.

I could ask a question about chipbreakers, sharpening, dovetails, bevel up vs bevel down .... but I shall spare you the hard stuff. :)

Instead, I shall post a link to a recent little table I built - started off as a demonstration at a tool event, and then I completed it as a bedside table for my son. The thing is, everyone must have built a few versions of this - I've built a number - and so you will have something to post or critique.

It has occurred to me that I shall build another at the next tool event as this little table offers the opportunity to practice many different joints: mortice&tenon, sliding dovetails, blind-and through dovetails, grooving, rebating, shooting, breadboard ends ... the list goes on and on. It's a wonderful project for someone wanting to hone their handskills.

There are a few perhaps interesting ideas here?

http://www.inthewoodshop.com/Furniture/ShakerStyleBedsideTable2.html


Regards from Perth

Derek

Re: Post your picture here ....

#2

Not woodworking, but......

roger lance

Hi Derek,

Things have been very quiet here for awhile. I've been involved in some other activities.....not woodworking. I've been working on various house remodel projects including re-doing the hearth which was relayed to soften (round) the corner.....


Next big project will be to lay a wood floor in this area. I've also fallen into a group of guys who are military vets that like to go shooting.....tell lies.....and have a few laughs. I've not been personally involved in shooting since my Vietnam days.....and have no interest in hunting.....just target shooting.....so I've been working on a couple of weapons and learning more about ballistics.....


Telling lies, I've got down.....

Re: Post your picture here ....

#3

Re: Post your picture here ....

CJ in MPLS

I have not had much if any output that is hand tool related. We're in the middle of kitchen remodeling and the garage is full to the ceiling with an amazing amount of stuff we had squirreled away in the old one.

I did manage to build a foyer for our smaller guests similar to some of the fairy doors seen in Ann Arbor, MI. A door with a transom window will be fitted into the front wall for access. Note that the wall lamp is functional and should provide illumination for a wee brownie returning home after a night of carousing with our cats; there can be no other explanation for the noise we hear each night.

CJ


Re: Post your picture here ....

#4

Re: Post your picture here ....

John in NM


I've been working on getting these finished. Mostly linseed followed by Waterlox and some wet sanding, a few were done with pumice instead.

While a number of power tools go into making these, there is a lot of rasp work in the shaping.

Re: Post your picture here ....

#5

Re: Not woodworking, but......

Derek Cohen (in Perth, Australia)

Hi Roger

Amazing the number of us building or remodeling at this time.

The past month I have also been using every free moment to rebuild a kitchen, a door, paint, paint, and paint. We bought a cottage as a rental, and are working to get it ready in the next two weeks before we are off to Cape Town for my father's 100th birthday.

I want to get back to the Wegner The Chair, but life is unusually busy with incidentals.

Regards from Perth

Derek

Re: Post your picture here ....

#6

Ellis Walentine

Wish I had something current

Ellis Walentine

Your tabel is a beauty, Derek. Apart from the breadboard ends, it teaches all the same skills as a quintessential American teaching project, the Shaker end table. The main difference is in the proportions. Shaker tables are a bit more delicate, and the tapers are on the insides of the legs, from the apron to the floor.

I actually built a couple tables for my better half and myself a couple years back. Wish I had more time to be building furniture these days. Here's a liink to that table project...

Table Project .

My next projects will be of a home-improvement nature. If anyone is interested in how I thread the needle between our 1781 house and 2014 improvements, that could be yet another topic.

Ellis

Re: Post your picture here ....

#7

Re: Not woodworking, but......

roger lance

Wow !!.....100th birthday !!......now that is really something......God bless him.....hope you have a wonderful visit.

Re: Post your picture here ....

#8

lack of productivity in the woodworking shop

GolfSteve in Calgary

Teaching the 4 year old to ride a two-wheeler (check)

Going to dentist to get night-guard replaced (check)

Cooking dinner for Mother's day (check)

Trip to Edmonton for the 7 year olds' Irish dance competition (check)

Guitar lessons every Tuesday (check)

Practising guitar every night (check)

Being nice to my wife every once in a while (check)

Raking lawn (check)

Sharpening lawn mower blade (check)

Getting ready for spring planting on May long weekend (check)

Changing over from winter to summer tires on my car (check)

Finding broken coil spring & repairing (check)

Changing over from winter to summer tires on wife's car (check)

Planning summer holiday (check)

Working 40 hours a week (check; well OK, only sort-of)

Grocery shopping (check)

Gotta buy a bottle of Scotch 'cause I've been out for a week.

Vacuum out mother-in-laws' car (check, loaded up on brownie points so we have a babysitter for the 10 year wedding anniversary holiday this fall I hope)

Bikes, spare tires, plants, snow shovels, etc. piled up all over the wood-shop. (check)

Way too many hours piddled away browsing the Internet (check)

Time for woodworking for the past six months = zero :-(

Re: Post your picture here ....

#10

ballistics

Jerry Gibbs

I cringe every time the TV crime shows refer to "ballistics" when they should say firearms identification. Jerry

Re: Post your picture here ....

#11

Re: Wish I had something current

Derek Cohen (in Perth, Australia)

Hi Ellis

Your table is a beauty. I love what you did with the corners of the top. It softens the lines and adds much character.

I've seen a few of your pieces now, and they all have this warmth. Please post more photos!

Regards from Perth

Derek

Re: Post your picture here ....

#12

Re: ballistics

roger lance

Hi Jerry.....I'm finding ballistics to be a very complicated subject of study and also very interesting. Last week, while working with my mil-mil scope, I looked into radians and found the origination of Pi (3.1416......) and its been nearly 50 years since high school math.....but now, I have a whole new perspective.

Re: Post your picture here ....

#13

Re: ballistics

CJ in MPLS

Ballistics is very much like photography in its complexity. For any given shot there is a selection of aperture size, shutter speed, film sensitivity, filters, framing, etc.

For some point and shoot is sufficient. Sorry for the pun. ;)

Re: Post your picture here ....

#14

Re: ballistics

roger lance

CJ.....I'm thinking but, so far, I can't top that pun. I do hope people here will see a connection/similarity in subjects like woodworking, ballistics, photography, etc....they are complicated disciplines that require a lot of effort and study and I'm guessing that the personality types drawn to woodworking are similar to those of people engaged in these other activities. I did have a love affair with photography long ago.

Re: Post your picture here ....

#15

Re: lack of productivity in the woodworking shop

Bruce McCrory

Sounds like you are having fun, Steve!

I did some deck power washing today.

[URL=http://s1343.photobucket.com/user/hbmcc/media/IMG_2368_zps19b8a398.jpg.html][/URL]

Pretty sloppy cleanup, however. So, will catch a few misses tomorrow, and go to the front, entry deck.

I have five gallons of finish but will pretreat the new replacement decking I collected over the winter; and let this one go. After 20 years and a new deck (the one you see) I can tell you all you want to know about decks.... And, more!

Re: Post your picture here ....

#16

Darrell in Oakville

Re: Post your picture here ....

Darrell in Oakville

I've been getting a wee bit of shop time lately. Managed to finish off a project that has been ongoing for over a year now: a pair of white pine closet doors. Doesn't look like much, but I had to make floats to make the panel raiser to make the doors. Lots of side trips on this project. First time for drawbored M&T joints for me. The doors have been primed, painted, and installed. She's VERY happy about the new doors, so much better than those awful sliding ones.


Another small project (on a very tight deadline!) was a candle storage box. I made this for a fundraising auction at a local church. It did very well at the auction because I made the box from wood from a 130+ year old maple that had stood in front of the church (the tree was killed by a lightning strike a few years ago).


Derek, I read your missive about the table project at the wood show. What I think you need is a second person at the bench with you. Someone who can talk about the work whilst you are doing it. And you can trade off too, taking turns working and talking. I bet you would get a table done in a day that way, and it would be a great performance to watch. Something to think about...

Darrell

Wood Hoarder, Blade Sharpener, and Occasional Tool User

Re: Post your picture here ....

#17

The pun was on target....

John in NM

But I shutter to think of it's impact! :D

Re: Post your picture here ....

#18

As always, the place is a barrel of laughs

Bill Houghton, Sebastopol, CA

as some random comment triggers an explosion of puns from the well-stocked brains of our members.

Re: Post your picture here ....

#19

Re: Post your picture here .... *LINK*

Kees

More carpentry stuff down here. I'm slowly but surely making some windows for the garden shed. At least it is working with wood. Better then all the painting that needs to be done too.

Here is a pic of the old ones. They are in very bad condition.

Some progress is documented on my blog.


img

http://seekelot.blogspot.nl/2014/05/windows-continued.html

Re: Post your picture here ....

#20

Re: Post your picture here ....

Derek Cohen (in Perth, Australia)

Derek, I read your missive about the table project at the wood show. What I think you need is a second person at the bench with you. Someone who can talk about the work whilst you are doing it.


Hi Darrell

That sounds like an offer to me! I accept!!

Regards from Perth

Derek

Re: Post your picture here ....

#21

Ellis Walentine

Thanks, Derek

Ellis Walentine

I appreciate your kind feedback. I wish I had more photos of my work. Heck, I wish I had more time to make new stuff. Hope springs eternal.

Ellis

Re: Post your picture here ....

#22

Didn't you mean...

Bruce McCrory

"well-loaded brains", Bill.

Re: Post your picture here ....

#23

Almost a reflex, isn't it? 


Re: Post your picture here ....

#24

It's almost automatic.  Semi-automatic, anyway


Re: Post your picture here ....

#25

Adam of Oakland

Re: Post your picture here ....

Adam of Oakland

Kees, I like how you joined the window frames for your garden shed (below). Have you test fit into the garden shed yeat? and how is your thumb doing? I snagged mine couple years back with a chisel, took 5 stitches at the ER to close up but no lasting damage (other than respect for shop safety):