New WoodChat!
Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Reach the woodworkers who ACTUALLY BUY

Got some cash to blow...

Posts

Got some cash to blow...

#1

Michael Donaldson

Got some cash to blow...

Michael Donaldson

I'll be at the LN hand tool event on March 1st in Minneapolis, and I've been saving up for it and will have about $250 to spend there. There aren't any tools that I can think of that I really need right now (I just know that I need more tools), but I am going to buy something. If you were in my situation, what would you buy? A new saw? A #148 tongue and groove plane? or would you keep saving and buy the LV shooting board plane? just looking for ideas to fuel my imagination.

Re: Got some cash to blow...

#2

Two questions to think about

Bill Houghton, Sebastopol, CA

1. What frustrates you about your current kit? If you find yourself sighing when you have to do certain procedures, either because the tools you own are limited or because you have to do it in a way that can be more efficiently done with a tool you don't own, that's one clue to what you might buy.

2. Are there projects you're not doing, or techniques you're not using, because you lack the tools to do them? That's another clue.

I was doing some consulting after I retired, and the deal my bride and I cut was I got 10% of the money for fun stuff. Much of it's still in the bank, waiting for the day that I can finish refurbishing the house and get into the shop, but I did buy quite a few tools because I thought I'd like to have them. Some of them have yet to leave the box, and I wish I'd held back a little on the buying.

Re: Got some cash to blow...

#3

Got a rasp?

John in NM

I know it's not bronze and cherry, but they are just the thing when you need one. Whether you will need one depends on what you make of course, but I've used the heck out of the one good one I own (came from LN, they put nice handles on them).

Other than that, I would suggest a saw. A good saw is another thing that is fairly hard to find.

All their other stuff that really gets me going is so specialized that if you don't know that you need it, then you probably don't! I do like the 99/98 pair though... seems like I keep cutting dadoes too small and then cutting them a little too big. Hard to sneak up on it with the table saw.

Then just to stir things up, have you considered spending some of that cash on some wood? Surest way to find out what new tools you need is to stress your ability to make stuff with what you have.

Re: Got some cash to blow...

#4

Save some of it for this show *LINK*

Bruce, a MN Galoot

The American Craft Council show at the RiverCentre in St Paul. BTDT, going back again this year. It's great! OTOH, it's only $12 to get in, so maybe you don't have to save so much.


ACC St Paul

Re: Got some cash to blow...

#5

Re: Save some of it for this show

Bruce Mack

That show looks grand, Bruce. Thanks for the information.

I too am going to the L-N fest. I want to handle the large router plane and the spokeshave.

Re: Got some cash to blow...

#6

Re: Save some of it for this show

Bruce, a MN Galoot

Get to the L-N show early. Last time (which is where I met Michael Donaldson and Chuck Bjorgen) I went to fondle the round-bottom spokeshave. By the time I got there on Saturday, they were out. It seems they don't take too many to sell. I won't be going this year because of my work schedule, but you could make plans to meet up with Chuck and Mike, both great guys.

I did satisfy my yearning for that spokeshave last fall. The Boggs one. It was worth waiting for.

Re: Got some cash to blow...

#7

Re: Got some cash to blow...

Chuck Bjorgen

I've decided to attend the Friday session. Have only been to two others of these events and generally don't carry any cash with me ( I know, credit cards). I like to have a cooling off period.

I'm pretty well set for planes, chisels and saws so I might not be terribly tempted to buy although my spoke shave setup is pretty rudimentary. Mostly just like to talk with folks and fondle some of the toys. I'm hoping to handle a well prepared card scaper to see if my efforts are not yet correct. Fortunately the location is not far from my home...only about a 20-minute drive.

Re: Got some cash to blow...

#8

Re: Save some of it for this show

Ray

I looked at the ACC link and didn't see any reference to tool vendors. What has been your experience in the past?

Re: Got some cash to blow...

#9

Re: Save some of it for this show

Bruce, a MN Galoot

As I recall, there were no tool vendors of any kind. And there will likely be crafts that don't interest. But the ACC boasted the membership of Sam Maloof, so it's not too shabby, either.

Re: Got some cash to blow...

#10

Re: Save some of it for this show

Ray

Thanks. I misread your reply-thought you were encouraging us to save our money for tools. The show still sounds great.

Thanks again

Re: Got some cash to blow...

#11

LN Tapered Tenon Saw

Phil

No idea how you are fixed for tenon saws, but if there is a need, you won't go too far wrong with this one: I've recently started using one and it is very nice:


Re: Got some cash to blow...

#12

Re: Got some cash to blow...

Curt Putnam

Once a year, when funds permit, I try to buy a tool that just makes my heart sing. There need be no other justification. Examples for me have been: An LN bronze #4, Chris Vesper marking gauge from 9000 year old wood, Blue Spruce mallet and paring chisels.

Re: Got some cash to blow...

#13

Jack Guzman from Maine

Re: Got some cash to blow...

Jack Guzman from Maine

Michael,I know exactly what I would buy if it was me but you aren't me. Don't plan anything. Get there with an open mind and I'm sure you will know exactly what you want when you see it. Enjoy---Jack

Re: Got some cash to blow...

#14

Sharpening

Wiley Horne--So. Calif.

Hi Michael,

If you're working and learning pretty much by yourself, I would suggest dedicating a piece of the Mar. 1 trip to discussing sharpening if someone is there to demonstrate. Even if your sharpening if very good, I would suggest this, as the subject is inexhaustible, and you're likely to pick something up that will be with you from now on. Saws or blades, it's the first among skills to own, and hands-on instruction is far the best.

As to LN tools I really like, a big favorite is the Boggs shave. On the other hand, if you get interested in stringing tools, I strongly recommend the LV offerings.

It's also a great opportunity to learn about rasps (as John cited). Get a demo of the Aurious, and get your hands on them. Reading doesn't convey what's going on--gotta get down with them.

Similarly, scrapers. Get a demo and some hands-on instruction. One of the most valuable skills of all.

Have a great time!

Wiley

Re: Got some cash to blow...

#15

Re: Got some cash to blow...

GolfSteve in Calgary

Hi Michael.

Without knowing what tools you have this is difficult to address.

But, my all time favorite purchases are:

LN 4.5

LN 8

LN dovetail saw

LV low angle block plane

LV spokeshaves

Drill press (very useful)

Big bandsaw (18")

Bosch fixed and plunge router set

Jessem router table

Jessem sliding table for the tablesaw. This is awesome and is a huge improvement (I have a contractors saw on a mobile base, so I don't have a dedicated outfeed table. The sliding table makes up for that)

Sata minijet 4 spray finishing setup

A good set of machinist squares (not necessarily expensive, just perfectly square)

A good straight edge (I like the Lv aluminum ones, but would love to have a starrett some day). The LV aluminum winding sticks are also surprisingly straight and strangely close to my heart.

Those are my favorites. Add a good set of chisels and you can anything.

Re: Got some cash to blow...

#16

Michael Donaldson

Thank you for the ideas

Michael Donaldson

I think at this point I am leaning towards the tenon saw (I don't have one, so I either use my dovetail saw or a panel saw, neither are ideal). But I'm excited to be ale to look around. I plan to be there right as they open on Saturday, if anyone wants to meet up. I'll wear a WC shirt.

Re: Got some cash to blow...

#17

Michael Donaldson

Re: Sharpening

Michael Donaldson

Excellent idea. I will definitely do this. Especially scrapers, I am yet to get a really good result with one.