New WoodChat!
Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

VPS-Level Performance. Fully Managed. No Hassle.

Panel gauge.....

Posts

Panel gauge.....

#1

Panel gauge.....

roger lance

When the gales of November come calling, I seek refuse by returning to the warm, dry confines of my basement woodshop....turn the radio to golden oldies, sip hot coffee, and try to make something. I've found that its wise to reacquaint myself with the shop by first making a jig or small tool before taking on a piece of furniture. This year, I decided to make a panel gauge....and, again I found that even this simple project involved the use of nearly every major large power tool I have and many handtools as well to complete (still have to make/attach a brass wear plate to the gauge).

But first was the gathering of hardware from sources like LN, LV, Woodpecker, and the local Ace Hardware.....


The blade can be extended or covered and protected by the washer.....


A pencil can be used on the other end of the beam.....when the kerf is closed, the pencil is firmly held.....


The panel gauge now joins the cutting gauges I made a year or two ago.....and my family of shop made tools grows.....


When the brass wear plate gets added, I'll show an updated photo. This was a good project.

Re: Panel gauge.....

#2

Re: Panel gauge.....

Lars Parrington

very nice. is the blade an exacto-knife part?

Re: Panel gauge.....

#3

Re: Panel gauge.....

Bill Houghton, Sebastopol, CA

Neat! What's the cutter made from?

Re: Panel gauge.....

#4

Re: Panel gauge.....

roger lance

Lars.....the blade is representative of a personal shortcoming I have.....which is my lack of ability to fashion my own parts in metal (but I'm trying and getting better).....the blade came from LN.

Re: Panel gauge.....

#5

Re: Panel gauge.....

BrianMonumentCO

A good looking batch of shop made tools !

Re: Panel gauge.....

#6

Adam of Oakland

Re: Panel gauge.....

Adam of Oakland

gorgeous panel gauge sir!

yes pls update when you apply the brass wear plate.

i like the alternate pencil holder end which to me would be great for when you're trying to scribe along the grain versus across it.

thanks for sharing. i have a panel gauge that i improvised in a sort of "heat of moment" fit of necessity while dimensioning some larger panels during a casework project. It involved a pair of carriage bolts, wingnuts and a sharpened bicycle spoke, i kid you not! trouble is that i ahve not upgraded the infernal thing but that should change i think...you've inspired me to do so.

Your idea of beginning a winter of woodworking by focusing on the tool first makes more sense to me now.

thsnks!~

Re: Panel gauge.....

#7

Re: Panel gauge.....

roger lance

Recently, I looked thru an old Garrett Wade tool catalog (real tool porn back in the day) and found the panel gauge they were selling used a nail to scratch a mark.....just a nail pushed thru a small hole in the beam. Now, there are more fancy gauges being sold by Lie-Nielsen and Hamilton Tool.....but, its more fun to make your own.

Re: Panel gauge.....

#8

Re: Panel gauge.....

Bruce, a MN Galoot

You've made a nice batch of tools, Roger!

Re: Panel gauge.....

#9

Great minds think ...

Derek Cohen (in Perth, Australia)

... alike. Really!

Roger, I like what you have done with the LN blade at the end of the arm. This creates a pseudo-Kinshiro-type cutter, which is makes for easier visibility and placement.

I have done the same thing, but with the LN inlay cutters. I have a mix of LN and LV inlay tools. I purchased the Latta radius cutter since I was following his video, and then decided that the straight cutter was simply a marking gauge, and that I had enough of these to convert one into a Cohen version ...


A similar one has become a slicing gauge.

Are you going to convert your marking gauges to fit the slicing blade?

Regards from Perth

Derek

Re: Panel gauge.....

#10

Re: Great minds think ...

roger lance

Derek.....thanks!.....the guys at the coffee shop don't think I have a great mind! :D

I did want to show you a variation I made. I remembered how you used a piece of brass to help secure your beams in your gauges. I thought about that and decided to make a recess that housed a circular piece of brass.....no where for the brass to go....this works very well....the beam is held very securely....



My cutting gauges use a blade sold by LV. Like all prototypes, I certainly could make the next cutting gauges better than these.....if you remember, I showed these gauges in one form and you then showed your Japanese gauges and I began altering mine.....mainly the fence....to look as they now do. I actually like these cutting gauges very much.....they perform very well....and they now have that ergonomic fit you spoke of. The blades are wedged into their beams at a 7° angle and it takes the use of a pair of pliers to dislodge them.....


I'm looking forward to your chair build.

Re: Panel gauge.....

#11

Re: Great minds think ...

Derek Cohen (in Perth, Australia)

Hi Roger

Clever. I like the captured brass - but is it wide enough not to dent the wood? Or is it pressing on a brass strip?

The brass plate I use is also captured.


There is a rod peened through it that slides into a hole inside the head. The screw presses down on the rod. The wide plate avoids denting the wooden arm.


Regards from Perth

Derek

Re: Panel gauge.....

#12

Re: Great minds think ...

roger lance

Derek.....denting is a non-issue.....I used hard maple.....and the brass is just under 3/4" in diameter with the edge of the brass relieved to avoid any marring.

Re: Panel gauge.....

#14

Re: Great minds think ...

roger lance

The width of the opening in the fence is about 7/8".....this leaves about 1/16" on each side of the captured brass disc so that it will not bind on the side of the fence. The diameter of the disc was reduced slightly from 3/4" so that it would fit in a 3/4" hole.....and the disc is about 1/4" thick.


Re: Panel gauge.....

#15

Re: Great minds think ...

Bill Houghton, Sebastopol, CA

This is very similar in size and design to the pressure "foot" on an English marking gauge in my shop - and far larger than the brass bar that Stanley used, with great success, on most of its marking gauges for years. So I don't think you'll need to worry about scars on your gauge's beam, Roger.

Re: Panel gauge.....

#16

Graduation pic....the bling is on....

roger lance

added the brass wear strip.....which the gauge really didn't need being hard maple....but this tool is now complete....on to other things....


Re: Panel gauge.....

#17

Some remarks on design/features.....

roger lance

I made this gauge with no plan or specific detail/dimension in mind. The length of the beam is 30" partly because I can store that length beam diagonally in a drawer of my large storage bench and also because that length should exceed any panel I'm likely to make for furniture. As I was making the gauge, my mental image of the gauge continued to change and evolve due to hardware, wood grain, feel, look, or what-have-you. An example of making these changes as you go is the brass wear strip. All along, I was intending to use epoxy to attach the strip.....that's why the green tape was being used.....to protect the raw wood from finish/etc. so the glue could bind. However, during the process of cutting out the wear strip, it distorted and I was leery of using a glue to flatten the twisted strip....so I turned to screws....but, the initial screws I wanted didn't work.....etc....etc. The point being you have to remain flexible and accept what you have to work with....make changes....and keep going to the finished piece. Thats also a part of getting acclimated to the shop and mentally ready to make furniture.

Re: Panel gauge.....

#18

Re: Graduation pic....the bling is on....

Chris K in MD

SWEET panel Gauge Roger!

Re: Panel gauge.....

#19

Re: Panel gauge.....

Patrick Gibbons

I know this is not important for use, but I really like how the three gauges look like a set. They will inspire your work.