New WoodChat!
Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

A55 Smoothing Plane

Veneer question

Posts

Veneer question

#1

Moses Yoder

Veneer question

Moses Yoder

There is not much hand tool content here but I think maybe a hand tool is the answer to my problem. I don't know a lot about veneering but the job I started at the end of February requires immense amounts of veneering. I am building these rangehoods.


The bottom is a front and two sides of mitered plywood with molding top and bottom. This is assembled separate from the top and when the top and bottom are completely assembled then the bottom is attached to the top. The top is made on a table with curved grooves to slide the sides into. A rib is put in the back and a gusset at the front, then a bulkhead is installed about 12" from the top and the front is attached. The sides and front are 3/8" bending ply. After fairing the carcase contact cement is sprayed on the two sides and the veneer for the sides. The two pieces of veneer are stuck to the sides with a veneer hammer, trimmed flush at the back and about 3/32" overhang on the front then sanded flush with a Dynabrade random orbit sander. The sides are easy and do not create a challenges. The front is what is a problem. The fronts are stuck on and trimmed close to the sides then sanded flush. I use 150 grit to sand the edges of the front nd then finish with 220 grit. The problem occurs when I sand a little to hard to remove the reulting glue line at the edge and sand through the veneer on the side at the front edge. Sanding through is a real PITA and requires stripping all the veneer off with laquer thinner and starting over. Hard Maple veneer, Oak veneer, and rotary cut Maple veneer that we use for paint grade is thicker and is fairly easy to sand with no sand through. Cherry and Alder are extremely difficult due to how thin they are. I would say on cherry every sixth carcase is ruined, on alder every fourth. Sometimes it is just a little and we send it anyway but I don't feel good about it. We mask the front edge of the sides with 3" masking tape but due to the curve it can't be masked perfectly so we don't waste our time trying. This results in a glue line at the front edge from the glue overspray that has to be sanded off. One thing to keep in mind is the speed at which these must be made; I am not a fast worker and build two complete units in about 9 hours. Of course my parts are already made, I just pull them off the shelf and mark them out of inventory. I thought maybe the collective wisdom here could come up with a solution, maybe a hand tool of some sort to trim the curved edge.

Re: Veneer question

#2

Small very sharp chisel plane?


Re: Veneer question

#3

I am wondering if

Wiley Horne--So. Calif.

Bill Tindall knows of a solvent that you could use to remove the last little bit of overspray glue, when you get down close. I know you don't want the solvent to get into the 'live' join, but maybe just the last little bit of glue could be removed that way.

Wiley

Re: Veneer question

#4

Spokeshave?


Re: Veneer question

#5

Re: Three options

Tom

1), kinda wasteful is to do two layers on the side, or look real hard for thicker veneer, or custom cut veneer.

2) You can consider, possibly as an upgrade danding the edges. These things don't sound all that durable. For what it must cost to buy them they seem to have very fragile edges, so what about a contrasting ebony like banding? That way you have a ton of beef in the corners. You do your veneering, then the router is used to cut in your channel, you drop the banding in and hit with CA.

3) option is to make a parallelogram trim router, and place the cases flat on their back and edge trim the coners, then scrape if required, though it is possible to set you to edge trim flush. You can router, or use a trim sander.

http://www.olsonguitars.com/artisan2/binding_ledge_arm.jpg

Olson went CNC and makes the most amazing jigs, but normally these are just made of ply. If you google fleishman binding jig plans and go to images, you will see the current version uses a sliding arm and a small parallelogram section, but the original is probably better for your situation. What this does is allow you to move a trim router anywhere you want, while maintaining it axial with the earth. You could easily use a trim router on your current project except for the fact that it is a compound curve, and difficult to get your base to register on. There are trim bases designed to freehand this situation, but they require perfect execution.

There are OEM version of this para thing. I forget what I googled to find them, they are for whatever industry uses them for, as opposed to luthier stuff. And they are very expensive. At least where I found them.

Re: Veneer question

#6

Jack Guzman from Maine

file

Jack Guzman from Maine

Moses,

When I formica a countertop and clean up the excess glue and fine tune the formica edges I use a small fine tooth half round file.I get alot of control that way.Different material but similar properties.---Jack

Re: Veneer question

#7

scraper

Bill Tindall, E.Tn.

I find I can control removal with a scraper best. Not sure it will work to remove contact cement though.

However, given the reject rate someone needs to attend a Mohawk furniture repair class. These sand-throughs can be fixed by an experienced repair person so they will not show.

Re: Veneer question

#8

Two ideas

Steve Elliott

Hi Moses,

If I understand your question, the issue is how to remove the small areas of contact cement that end up on the surface of the veneer where the masking tape doesn't perfectly line up with the curved edge.

My first thought is to change the method of masking the edge to avoid letting contact cement get on the veneer in the first place. Could you apply wide pieces of masking tape to the side pieces of veneer before they're applied to the curved sides? The masking tape would be left in place while the veneer is trimmed and contact cement is applied for the face piece. That would insure that the masking would reach the edge perfectly, avoiding the need to remove contact cement from the veneered surface.

To know where to put the masking tape on the flat piece of veneer I'd use a marking template and chalk. The shape of the template could be based on a piece of veneer that had to be removed from a side, or it could be taken directly off the curved side using a large piece of cardboard and a pencil.

Sanding contact cement off is always difficult because it's so rubbery and doesn't sand down as fast as wood. I'd start with a scraper and try to take off the thickest parts by just shearing them off. They won't cut well but it might be possible to take off the thickest parts. What's left will be spots where contact cement has soaked into the veneer. These might come off with lacquer thinner or maybe careful sanding would work. Any solvent applied to the surface could soak through and compromise the bond underneath so I'd use solvent very sparingly, maybe just a slightly damp rag rubbed back and forth until the combination of abrasion and chemical action overcomes the bond of the cement.

Re: Veneer question

#9

Re: Veneer question

roger lance

Moses....when I've used "contact cement" for applying laminate, I used mineral spirits to remove excess glue....worked extremely well.....and, of course, mineral spirits should evaporate and not interfere with your finish. I know we are sometimes reluctant to read the instructions on the can; but, what is the solvent for the contact cement you are using?? Another thought would be to finish the sides before you glue on the front veneer with the hope that the contact cement will not stick or penetrate the side veneers as much and make clean-up easier.

Re: Veneer question

#10

Mineral Spirits & Contact Cement

Steve Elliott

Paint thinner (mineral spirits) is my favorite solvent for removing contact cement from laminate. It works more slowly than lacquer thinner but the contact cement ends up in little balls that can be brushed off the surface instead of leaving streaks on the surface where lacquer thinner has thinned the cement and allowed it to stick back down.

I'd be concerned about using mineral spirits on veneer bonded with contact cement. It will probably soak through and may end up compromising the bond. I don't know the chemistry of what happens with mineral spirits and contact cement but it seems to be different from lacquer thinner, which just thins the cement down and allows it to work as intended after it evaporates.

Re: Veneer question

#11

Re: Veneer question

Paul M.

That edge looks to be a very gradual curve. Have you considered adding a very small moulding along that edge between front and sides? If you had a small 0.5x0.5 block with a 0.3x0.3 corner removed, then you might be able to steam bend the resulting small moulding to fit the corner curve.

Just a thought. This would add some protection for that very vulnerable veneer corner.

Re: Veneer question

#12

Re: Veneer question

Paul M.

Replying to my own reply...

Another idea would be to use thicker veneers. Certainly Wood carries 1/24" or 1/32" veneer in most domestic woods. They have lots of 1/16" veneer too, but that's thick enough that it could put up a fight for laying down onto your bendy plywood subsurface.

Re: Veneer question

#13

Following on to Steve's ideas...

Wiley Horne--So. Calif.

Here is a flexible, very hard scraper which holds its edge well. These things are magic for removing small problems, because they're so sharp, and it's difficult to do damage to the underlying wood, because they're flexible. Put a light hook onto one end or edge, to see whether hook works best or not:

http://www.leevalley.com/US/Wood/page.aspx?p=49548&cat=1,310,41069&ap=1

This is one of my favorite things that Lee Valley carries. Yeah, 2 for $11.50 is kinda expensive, but two is all you'd ever need.

Again, following Steve's thought, could the final detailing after scraping be done with fine abrasive paper dipped into mineral spirits, just enough to moisten what you're trying to remove?

Wiley