New WoodChat!
Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Precision you can feel — woodworking perfected with Lee Valley

Lapdesk

Posts

Lapdesk

#1

Lapdesk

Derek Cohen (in Perth, Australia)

After the completion of the box for the bridle plough plane, I was left with the smaller section on the left.


It occurred to me that this could form the basis for a lapdesk, that is, an interpretation of a campaign lapdesk. I love the simple, clean lines of campaign/military furniture, and the thought of building a piece with secret spaces promised to be fun.

There are many really interesting campaign pieces. For example ...


I would call my pieces "campaign-inspired". They are not exact copies of originals, as Chris Schwarz is currently building. Instead they are my interpretations of this furniture type, taken in a contemporary direction. An example are the military chests I built close to 2 years ago (see http://www.inthewoodshop.com/Furniture/TheCompletedChests.html ).

Now I have a lot of pictures, so brace yourself. The thing is, I need some advice. I completed 99% of this build, and then had second thoughts whether I should ad the last element. I shall leave that for last.

Let's start here. A pic of the outside, to be compared with the remnant above (15" long x 11" deep) ..


The body is clothed in West Australian She-oak, finished in Organoil Danish Oil and wax.


There are two lids, one for the pen-and-ink section and another for the main storage area (which is empty at present - more later) ..


There is a drawer for some of my fountain pen collection (they all get rotated for daily use in the notes I take all day long), a tray for pens in use, and an ink well ...



There is space for a iPad ..


The fun in building this lapdesk was in creating the secret hiding places. There are 4 in all. The first is hidden very securely under the console. To get to this one must remove the console. It is secured on steel pins (in the corners). Lift the console straight up and a hidden panel is revealed ..



The inkwell in the console is walled internally ...


Now, at the rear of the console there is a slot wide enough to hide the key(s) to that important chastity belt or safety deposit box (whichever is more important) ..


The drawer ...


... has a false bottom. This is accessed from the rear of the drawer.


Slide away the rear panel ..


You can also remove the pen tray ...


Now that is three of the hiding places. The fourth?

This introduces the dilemma I have. Sometimes less is more and adding one more item makes the piece too busy, too complex. I have presented the pictures in the order I assembled the lapdesk, and it may be a result of this that I am feeling this way. Do I include the last section or not? I would value your input here.

There is a central cover that was designed for three purposes. The first is that it offers an additional writing surface. This is Jarrah - I thought a wood to link in with the console. Some thought went into balancing the figure with the parts of the console.



The second purpose of the cover is that it hides what lies within.


And hidden inside the cover is another drawer ..


The hinges have not been installed as I am not sure whether to keep it or not .....


Regards from Perth

Derek

Re: Lapdesk

#2

Stephen Shepherd

Nice Lap Desk Derek!


Re: Lapdesk

#3

BEAUTIFUL!!!!


Re: Lapdesk

#4

Re: Lapdesk

TomD

How does it work, seems like the lid would make it hard to use? Nice work!

Re: Lapdesk

#5

Re: Lapdesk

William Duffield

Derek,

That's a great lap desk design, and beautifully executed. If I were building one, I would start with your ideas, and I would definitely add the interior cover. Of course my requirements would be somewhat different from yours. The key requirement is the iPad, and my clamshell keyboard is my problem. It has a tendency to drop the iPad without any warning, especially when I'm typing on it. However, I really dislike the interface of the iPad's built-in virtual keyboard, so a real keyboard is necessary for any semblance of productivity. So, if it were my lap desk, I would build the cover so that it would securely hold the iPad on its top surface, and would be able to prop it up at several different angles. I would also adapt the open lid to hold the keyboard. Inside, I don't need an inkwell, and since my mechanical pencils and Pilot P-500 pens are disposable, I don't need protection for something like your expensive fountain pens. I do need space for cables, chargers, spare cell phone and camera batteries, interface devices and data storage, and of course a pad of Veritas graph paper. Hidden compartments would be very useful for flash memory devices. I would use the graph paper with the desk closed.

I haven't used a fountain pen since high school, but I did learn to type on a totally mechanical upright Royal typewriter, over 50 years ago. I refined my typing skills on a keypunch machine, before the word processor was invented.

Re: Lapdesk

#6

Ingenious!

Wiley Horne--So. Calif.

Holy cow, it's a James Bond model. Can you could get away walking through a (U.S.) airport with that? I'm having a smile thinking about the baggage inspectors going through it ('secret compartment?' gun pen?).

Beautiful job, and most ingenious.

Wiley

Re: Lapdesk

#7

that was a fun read

Bill Tindall, E.TN.

I am sure you are anxious to begin campaigning with it :)

Re: Lapdesk

#8

design question

Jerry Gibbs

Did you design this on paper, a computer or in the field? I would have trouble drawing this. Jerry

Re: Lapdesk

#9

Re: Lapdesk

Joanne in Point Pleasant, PA

The one I built quite a few years ago was much simpler than Derek's. It did, however, have a ledge on the front cover to prevent items from sliding off. It had a drawer that pulled out (I think a secret cache in there; don't remember and it was a gift for someone else) and storage inside. The hinge was at the top on the one I built. Wish I had more of that great mahogany!


Re: Lapdesk

#10

Jim DeLaney, Austintown, Ohio

Re: Lapdesk

Jim DeLaney, Austintown, Ohio

Here's one I built last year - a three part fold-out patterned after a 17th century British Officer's Desk.


Re: Lapdesk

#11

Re: design question

Derek Cohen (in Perth, Australia)

Jerry, I design by obsessing :)

I wish I could put these ideas into CAD - I have to find the time to learn to use the program I have. I sketch a little, but rarely to scale and it never looks like the images I visualise.

So I start building the outline using rough dimensions as a guide. I need to see the dimensions working to keep them. I will try out ideas as I go along, discarding if necessary. If nothing else, some of my builds must demonstrate how often I change direction during a project. This does not worry me - I see it as a hands-on method of developing a design. If I had the time and patience I might make a model or two.

Experimentation and obsessing ... :)

Regards from Perth

Derek

Re: Lapdesk

#12

How to use it.

Derek Cohen (in Perth, Australia)

How does it work? Tom, I imagine myself writing notes on the top of the case, lifting the rear lid to access a pen or ink. The front lid folds down perfectly (by design or luck) at the correct angle so that the inside of this lies coplanar with the centre lid/cover, thereby creating a long working area. I cannot see myself using it this way, however. The inside is really for storage.

The desk is for writing, not reading. Hence there is no "lip" at the end to prevent papers or books from sliding off. This would be awkward for writing. Without the lip, papers/pads may be moved to their ideal angle, moved up or down or along.

My plan has been to add on the underside of the cover an elastic (diagonal) grid for envelopes.

It was largely intended as a fun project, hopefully with a practical side, but mostly for fun.

Regards from Perth

Derek

Re: Lapdesk

#13

Re: Lapdesk

Derek Cohen (in Perth, Australia)

The key requirement is the iPad, and my clamshell keyboard is my problem. It has a tendency to drop the iPad without any warning, especially when I'm typing on it. However, I really dislike the interface of the iPad's built-in virtual keyboard, so a real keyboard is necessary for any semblance of productivity. So, if it were my lap desk, I would build the cover so that it would securely hold the iPad on its top surface, and would be able to prop it up at several different angles.

Hi William

I may store the iPad inside the lapdesk, but I cannot envisage using the lapdesk with it. The lapdesk is a surface for writing with a fountain pen, rather than typing on a keyboard.

I, too, have a keyboard for my iPad. I take it with me on trips because it makes typing reports, email, etc so much easier (I was converted to this idea after one overseas trip when I lugged around my MacBook Pro and developed a hunch back and a crooked shoulder). The keyboard comes with its own case with built-in stand for the iPad, and connects wirelessly. So light, so sensible.

Regards from Perth

Derek

Re: Lapdesk

#14

Re: Lapdesk

Philip Duffy

Once again, you have outdone yourself, Derek! Beautiful workmanship and I love the hidden compartments. Phil

Re: Lapdesk

#15

My 2 votes are keep it & safety deposit box


Re: Lapdesk

#16

Wow!  3 great pieces in 1 thread


Re: Lapdesk

#17

Question on #4

Alex Y

But before I ask it, let me say (in light of another recent thread here) that I am envious of BOTH your design and execution ability.

What does the middle lid rest on when closed? Are some stops installed or contemplated, which are not installed in the earlier photo?

I love hidden compartments like these, and I think the first three are very clever and well-hidden.

I vote FOR the middle lid, but against the hidden drawer there. My concern is that the middle lid looks heavy compared with the rest of the piece (at least to my eye from these photos). That makes it look like more than a lid, thus making the hidden compartment more likely to be discovered. I think the middle lid would look better being the same thickness as the outer lid. You may still be able to hide a small secret drawer in a thinner lid, but I would worry that the outer piece would be too thin for a full-size drawer as you show here.

Just my $0.02 worth.

Beautiful work.

Re: Lapdesk

#18

Re: Question on #4

Derek Cohen (in Perth, Australia)

I vote FOR the middle lid, but against the hidden drawer there. My concern is that the middle lid looks heavy compared with the rest of the piece (at least to my eye from these photos).

Hi Alex

There is some merit in what you say. I also came to the conclusion that the centre lid being heavy. However, the secret drawer stays if it stays. It is really the main reason for having it.

One solution that occurs to me is to bevel the undersides of the centre section. This will lighten the look/give it a thinner appearance when open. What do you think?

I am also giving thought to the hinges. They need to disappear. Placing them vertically (between the outer and inner edges) is my current plan. That way all you see is a thin brass line above the butt hinge.

Regards from Perth

Derek

Re: Lapdesk

#19

I've reconsidered

Patrick Gibbons

The first lid, once closed, would be used to write on. There is not a reason for the second inner lid. It's clever for the secret space but not necessary. I believe it would be nonsensical. Add in the extra weight and it seems more and more to sully the whole design.

Re: Lapdesk

#20

Evolving the design.

Derek Cohen (in Perth, Australia)

Hi Patrick

You know, I came to the same conclusion last night. I was thinking that I liked opening the lid and seeing inside, that the centre lid/tray was heavy-looking, and so I planned to toss it.

Today I was staring at this picture ...


... and had this inspiration. It occurred to me that the lid/tray could be made thinner looking. All I need to do was bevel the sides (downwards). It is a frame-and-panel construction and there is enough there to work with. I would leave a square edge equal to the width of the sides (for continuity), and the remainder would be bevelled.

... and THEN it also occurred to me that this section could make a useful stand for a iPad and a wireless keyboard. Place the iPad on the lid/tray (adding a brass stay to fix it at the desired angle), and place the keyboard on the inside of the sloping lid. Itts angle should not affect typing.

Now, if I attach the lid/tray in such a way that it pivots on a bracket/hinge about 1/2" from the edge of the centre section, it will open to create a small ledge. This would be ideal to secure the underside of the iPad. In other words, no extra lip required to be added to the construction.

And, of course, the centre lid/tray remains with its hidden storage.

What do you think?

Regards from Perth

Derek

Re: Lapdesk

#21

Re: Evolving the design.

William Duffield

Yup, that's what I would do if it were mine. I think it is similar to what I suggested. Before you install the tilting lid/tray, you need to measure the combined thickness of your iPad, your Bluetooth keyboard and whatever writing materials you plan to carry with them, to make sure you have room for all of them and the hidden compartment in the lid/tray.

Re: Lapdesk

#22

Re: Evolving the design.

Alex Y

With the middle lid "repurposed" as you describe, My concern for its thickness goes away.

Be sure to post the final version -- I can't quite picture how you are talking about hinging it, so I look forward to seeing a picture.

Re: Lapdesk

#23

Re: Evolving the design.

Jay St. Peter

My personal feeling is that I like to see the inside. Is there a way to mount something to the inside/bottom that can raise up to hold your iPad, but still allow you to see the nice work you did on the pen holder section and allow the drawer to open. Didn't think it through at all, just throwing something out there.

Re: Lapdesk

#24

Re: Evolving the design.

Patrick Gibbons

Derek, I like your new thinking on the part. My original trouble with it concerned it having no purpose other than to hide a secret compartment. Repurposing it for the iPad gives it enough significance to retain it. The weight issue is an unknown to me since I am not in physical proximity to heft it. But it's just a fun piece. It should bring a smile to your face with each use.