New WoodChat!
Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

This is the most versatile work station you will ever use

What are you working on? April edition

Posts

Re: What are you working on? April edition

#26

Re: What are you working on?  April edition

Kevin French

I just had a 15 yd dumpster dropped out by the barn. It's going to be a hell'ahva spring clean up and barn clean out in prep for building the first 2 of 4 mushroom growing rooms.

Re: What are you working on? April edition

#27

Shop paneling

Hank Knight

I've had white peg board on the walls in my shop for years. I never liked the look, but I love the utility of the stuff. Recently, I got the itch to replace the peg board behind my bench with something more attractive and spruce the place up a bit. While I was thinking about what to put up, I kept stumbling over a pile of #1 common walnut I bought cheap in the Fall and piled in the middle of my shop floor until I could find a place to store it. Finally the light went on - I'll hang it on the wall. I took it to a friend who runs a millwork shop and had it milled into V-groove paneling. I hope to have it up by early next week. Then I'll need to make some hangers to replace the peg board hooks for my tools. While the wall was bare, I took the opportunity to reconfigure the conduit and wiring behind the bench and add a switched outlet for some more lighting. It should be a significant improvement over the old peg board.

Hank

Re: What are you working on? April edition

#28

not the best idea for lighting

Bill Tindall, E.TN.

If the area around the bench is light colored- the ceiling, floor and walls- any light that drifts uselessly in these directions is reflected back to the bench area. It can make a large difference enhancing the light intensity at the bench surface by half again.

It is common that a person entering my shop for the first time is sufficiently impressed by the lighting that they blurt out some comment on it. These comments suggest two things- my brother- in- law lighting engineer offered sound advice and many people endure less than optimum shop lighting.

Re: What are you working on? April edition

#29

Re: not the best idea for lighting

Hank Knight

Bill,

Ordinarily I would agree with you; but I this case, I don't think the dark walnut will hamper the lighting at my bench. The paneling I am replacing is behind my radial arm saw bench which is behind my regular workbench, I.E., I work with my back to it unless I'm using the RAS. I have plenty of lighting over my workbench, and I'm planning on adding some track lights over my RAS bench that I can aim as necessary for the RAS. If it turns out you're right, I'll paint the walnut white. :D

Hank

Re: What are you working on? April edition

#30

Dale Lenz

Yes, I've heard of White Walnut,

Dale Lenz


Re: What are you working on? April edition

#31

painted walnut

Bill Tindall, E.TN.

A long time ago there was an "energy crisis" and among the things that happened was that the price of coal went way up. Instant millionaires were created in the coal country north of here and they spent lavishly. We sold walnut lumber for a kitchen. The head of the kitchen decided it was too dark and had it painted. It was likely not the worst extravagant waste of money that happened but for a wood enthusiast it was annoying. The kitchen walnut lumber grade was much higher than your paneling so the assault on my sensibilities was heightened. I have seen #2 common walnut sell cheaper than a good grade of poplar and again much higher. When it was fashionable for floors it was quite dear.

Re: What are you working on? April edition

#32

Re: not the best idea for lighting

TomD

Guilty as charged. When i moved into my current shop, there more than adequate fluorescent fixtures overhead. Like 24 in a double length garage. I took them down to drywall and insulate, and they have never gone back up. My light is bad, and I need to address it. At least my walls are all white. Well... except for all the tool racks...