Spring
Pole Lathe
Posts
Re: Pole Lathe
#27pic to come
John Pappas
Will do, my lathe takes some set up. May not get to it until Fri.
Re: Pole Lathe
#28Re: lathe chip scatter
TomD
On cylinder type work I do a hand over grip if I want to control the chips. They all end up in my hand.
Re: Pole Lathe
#29
Massive machine!
Jack Guzman from Maine
How old is that beast? ---Jack
Re: Pole Lathe
#30Story on the unusual lathe
Bill Tindall, E.TN.
I owned an inexpensive lathe that was becoming limiting in my lathing desires. I wanted to build a spool bed and the posts are a bit longer than what many lathes could handle. I hoped to be able to buy a replacement lathe that would turn these posts(see PIC).
I was brushing up on my spindle turning with Nick Cook in Atlanta and I asked him about lathes with a bit longer bed. A defunct shop sharing his building had one, he said. Indeed! It was two Powermatic 90's welded together to make a lathe suitable for column turning. They had likely come from some school shop from back in the day there were school shops and they had been expertly welded together. It happened that the owner dropped by as I was finishing up and I bought the lathe with the understanding it would be delivered. Some time later she called to explain she could not get it loaded in her van (Duh!). It is 11' long and weighs 1100 pounds.
It got moved to Redmond Machinery on consignment and never sold. Months later I got a call from the owner asking if I was still interested and that Redmond would deliver....for a price. Wife had what turned out to be an outstanding idea. I advertised in the paper for someone to haul it the 300 miles to my house. Many responded (and idea for future reference) and in the end a professional trucker coming home for Christmas delivered it for a modest fee. Neighbor unloaded it with a front end loader onto a plank with casters. I tied it off to the the truck and eased it down a ramp into the basement shop. Some come-alongs fastened to bolts through the floor joists easily hoisted it into position.
Contrary to what I had been told it had a 3-phase motor. In what turned out to be an outstanding suggestion, instead of replacing the motor I ran the 3-phase from a variable frequency drive which provided continuously variable rpm's, and reverse, a highly desirable feature. This same drive provides continuously variable rpm/s to a bench grinder for sharpening tools. I hope to add a three phase motor to the drill press to get similar advantages.
Re: Pole Lathe
#31Nice! And a question...
John in NM
Is the torque from the motor constant with a VFD? A friend asked me about that last week and I couldn't come up with an answer off the top.
I have a similar, if shorter and newer lathe.... still have never quite got the hang of turning 
Re: Pole Lathe
#32answer
Bill Tindall, E.TN.
Back before I was relieved from Articles editing duties I reviewed a submission that covered this topic. See if it was ever posted. I think the conclusion was that the torque at slower speed was less. It has never been a limitation on this 1 HP lathe motor. But, I don't so bowls but I do up to 4" spindles.
Re: Pole Lathe
#33Thanks Bill, I'll look for it
Re: Pole Lathe
#34mess
Bruce, a MN Galoot
this is the mess from turning
Corian:
Re: Pole Lathe
#35Re: mess
David Weaver
what were you turning, elmers glue-all?
Re: Pole Lathe
#36Re: mess
Bruce, a MN Galoot
I was turning a small bowl of Corian on a face plate just to see how it worked. I wasn't prepared for the static cling. Uffda!
Re: Pole Lathe
#37
Re: mess
craigd
Is this what you look like?
Re: Pole Lathe
#38Not quite THAT bad
Re: Pole Lathe
#39Re: mess
William Duffield, in Winter Haven
Except for the color, that looks a lot like the results I got from turning the hand wheels for my Moxon vise from bloodwood. When you lose the static charge, the Corian falls away. The bloodwood, due to the oils, doesn't. To make matters worse, I had a fan running, and hadn't swept up the spider webs before I started.
Re: Pole Lathe
#40Re: mess
Bruce, a MN Galoot
I think your mess must have been worse, Sir W. However, mine didn't go away willingly, what with the humidity level approaching zero. It was a bear to clean. I have since done similar projects in our humid summers, with none of the same effects.
Re: Pole Lathe
#41Re: Spring
John Pappas
Ron, I wasn't able to get a clear picture of the spring arrangement for various reasons. What I have is this. A 1" diameter dowel mounted between floor joists (parallel to the joists)....so that I can move the spring left or right over the work piece as needed. My spring (16" long, 5/8" diameter...I think a screen door spring) is connected to the rod, and then the rope from the spring wraps around the work. I have no experience with a real pole lathe, so I don't know how this would compare in a side be side test, but it does work. I will add that my lathe is a crude device, not much used, but I have been able to turn a few things. One more thing, my lathe is really just the bed part, which I made to be mounted between a vice on my workbench and a WorkMate workbench. When not being used, it hangs in the corner of the shop.
Re: Pole Lathe
#42Thanks
Re: Pole Lathe
#43Alternatives
Bob Hackett
FWW put out one of their compendiums of lathe related articles a while back. Among the articles in that collection were a few home made lathes powered by the leg alone up to and including one that used a bicycle drive hub to drive the work so that the work rotated in only one direction. Use of the hub coupled to a chain and spring attached to a treadle also allowed for variable speeds.
The internet also will provide variations of everything from a pole, bow, spring, treadle, great wheel, etc human powered lathe with less than an hour`s research (providing you don`t become distracted). 



