We value your privacy.
We use cookies to enhance your browsing experience, analyse site traffic, and personalise content.
By clicking “Accept all”, you consent to our use of cookies. You can also choose
“Essential only” or learn more.
I still use the brick red setters wax, on the rare occasion I cut anything. The stuff I put in the wax pot was a very dark brown wax and more brittle than the red stuff. Still worked fine though, for all but the tiniest stones.
I showed up at the Tucson faceting club once with my bernzomatic torch for dopping, and enjoyed the startled looks and eye rolling Its fast (and I already had one - do you see a trend in my cheapness? ), and works fine if one takes care not to smoke the wax. I always find it amazing how many ways there are to do anything if one just experiments rather than learning the single "right" way
I've tried the iron-on approach with PVA and veneer. Worked ok, but not as well as about 3 other methods I've tried. I've read that it only works well for maybe 12 to 24 hours after rolling on the glue - but that was yellow glue. I remember hearing also that this was one application where white glue was better than yellow - perhaps the hot melting works for longer or indefinitely?
The really nice thing about vacuum bagging is that it doesn't matter which adhesive you use, as long as it has enough open time to assemble and get it in the bag. I've made curved laminated parts using West System epoxy that way (with some wax paper over it to protect the bag of course). A lot of glues tend to boil if there are spaces where the bag can't stretch enough, but as long as there is pressure on the laminations there won't be bubbles where it matters.
If one were fast enough, they could in theory use hide glue in the vacuum bag too
The chemistry differences between white and yellow glue suggest that white would be a better hot melt.
The veneer now days is so thin that in any case the bond could be steamed and steam will soften either yellow or white unless one is using one of the yellow crosslinking varieties, for example TB II.
I've used regular yellow glue (original Titebond) and white glue successfully, but I wouldn't recommend the cross-linking, water resistant types. They require higher heat to get a good bond and after they've fully cured and become "waterproof" they don't rebond with heat or moisture.
To get a secure bond you'll want a good coat of glue on both surfaces, either one heavy coat or a couple of lighter ones. Before placing the dried glue surfaces together run a wet sponge over one surface to add a layer of moisture right where they will meet. Heat and some pressure get the layers of glue to fuse together.
This isn't a good technique for large surfaces, better for curved edges where clamping is difficult. The heat of an iron can dry out a wide piece of veneer and cause cracks. I used to make production runs of round tables and would wrap the edge around, then trim both pieces with one knife cut and iron down the joint.
For a while I was covering surfaces with parchment and used white glue. The surface to be covered had to be flat and white (the shop used gesso for this) and the glue had to be transparent. White glue is softer and bonded to itself quite easily. Too much heat would scorch the parchment.
Before using this technique on a project I'd suggest some trials to get the heat right and learn a way to hold down the veneer until it cools enough. A block of wood that follows the iron works fine for this. Without it the edges of the veneer can lift due to curling and leave gaps at the edges.
Your experience with parchment greatly exceeds mine, and as I was doing the work in question I wondered about what the traditional methods were. After the pieces left our shop I never saw them or heard of them again, so I don't know about the long term behavior of the glue/parchment combination.
We used two methods with parchment, both using white glue. For large surfaces we soaked the parchment and stretched it a little over a layer of wet glue. Bubbles that turned up after the parchment had dried overnight were a problem and they were difficult to repair. On frames the dry glue technique made it easier to get tight joints in the skins and the much rarer bubbles were easy to fix because the parchment had a layer of glue bonded to it. A tiny knife cut to let the air out and a touch with an iron bonded it right back down.
I liked working with the dry, paper-like parchment but soaking it turned it into actual skin again, which gave me the creeps. I like the subtle texture parchment has but my taste runs more toward materials that are easier to understand and repair, not things that need expert conservation.