New WoodChat!
Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Compare cordless drills on the numbers that matter

Cutting and cleaning up tapers......

Posts

Cutting and cleaning up tapers......

#1

Cutting and cleaning up tapers...... 

roger lance

Today, I'm making use of that band saw tapering jig I showed before by forming the legs for the dining room table.....as the thickness of the legs and base width of the jig exceed the capacity of the table saw, its good to have this jig which is additionally much safer than the old table saw jig I was using....even if it does have a Rube Goldberg quality.....


Now its off to the bench to make use of the bench vise aid that William Duffield demonstrated and a little plane work to remove the machine marks.....


Thanks for looking.

Re: Cutting and cleaning up tapers......

#2

Re: Cutting and cleaning up tapers......

Wiley Horne--So. Calif.

Hi Roger,

The jig certainly is effective. The thing that caught my eye though is the taper-holding-vise-fixture. I first saw it in a Sir William post. Is that about a 20-25 degree angle on the swiveling board?

Thanks for showing,

Wiley

Re: Cutting and cleaning up tapers......

#3

William Duffield's vise taper jig.....

roger lance

Wiley.... the taper I used on my version of William Duffield"s jig is 10° on each wing.....I just made it from available scrap....a thicker piece would allow a larger angle....its a handy device and I thank W. Duffield for it....certainly added to the value of these discussions. BTW, I also used your suggestion of making a real life mock-up to test for fit on distance below the apron to floor.....takes away some of the guessing.

Re: Cutting and cleaning up tapers......

#4

Re: William Duffield's vise taper jig.....

William Duffield, between Lake Dexter & Lake Ned

The credit should go to Steve Latta. At least, that's who I learned it from. I've shown my version of the bench-on-bench at several venues, and am always surprised that the taper holding jaw/jig always seems to be the most appreciated.

Curiously, when I cut tenons on the bandsaw, I just draw a line, cut close freehand, and clean it up on the joiner. (#7 works as well as the DJ-20 for this job.) Lately, however, I've been using another jig by Steve Latta, for the table saw. If I haven't posted that here, I'll do it as soon as I get back to the Cohansey and get access to my photos.

Re: Cutting and cleaning up tapers......

#5

Progress..... 

roger lance

subassembly dry fit.....


went with a 1" curve on the apron....should maintain strength and provide comfort.

Re: Cutting and cleaning up tapers......

#6

A nice shop, Roger


Re: Cutting and cleaning up tapers......

#8

Thanks Bruce and Bill.


Re: Cutting and cleaning up tapers......

#9

More progress.....it's gonna be a big boy....

roger lance

I'm thinking that I will spare myself the task of trying to get this base up the stairs and simply complete the glue-up upstairs in the dining room....the top will also be fun....thank goodness for strong friends....


I'm also half liking the long aprons without an arc.....thoughts??

Re: Cutting and cleaning up tapers......

#10

Re: More progress.....it's gonna be a big boy....

Bob Entwisle in NJ

Coming along nicely, Roger.

Good idea, hauling it up in pieces and gluing it upstairs, but watch the squeeze out.

For me, I'd like to see the arc on the long rails too.

But Once the top is on only a woodworker would notice them.

Nice work.

Bob in NJ

Re: Cutting and cleaning up tapers......

#11

Re: More progress.....it's gonna be a big boy....

Charles Jackson III

Is that a table you is making?