New WoodChat!
Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Portable Sawmill & Tree Service – Abingdon, VA

Does anyone work in metric measurements

Posts

Re: Does anyone work in metric measurements

#26

Re: Canadian problem - Taps

TomD

Princess auto sells the sets. They are ridiculous cheap. The handles I toss. The dies and taps are OK, and any I wear out. I buy over in better quality. I use, KBC in Brampton, Busy Bee. And I order stuff off ebay, and from victorynet. But metric is always less available so today, I couldn't get M6 caps. The situation in Canada is getting worse as we are being eaten by US companies that have minimal metric exposure. So a KBC has way less stuff, and it either blew up a domestic supplier, or just offered way more into the market, not sure, but the end result is we are as smart as if California had gone metric (which if you turn down the wrong hall in Sacrimento, it probably has an office of metrification, "hard at work).

And in fairness Metric taps are a better deal, since they have a simpler system for at least the standard sizes, but in the real world there are twice the options in Imperial.

Re: Does anyone work in metric measurements

#27

Re: What am I missing here? - divide by 5

TomD

Yeah, and if you make five drawers, why would you make them all the same size, in every case. I like to have a regular increment of increase.

Re: Does anyone work in metric measurements

#28

Re: Cms . . .

TomD

And these days you could get a digital caliper that length and do a decimal inches thing, and since in digital imperial is twice as accurate, I am not sure I see the benefit. Not to say there is a problem, either. Some of the calipers even talk to your computer.

Re: Does anyone work in metric measurements

#29

Re: Imperial is more accurate

TomD

Not that it matters. But a lot of stuff like decimal inches vs. metric, the standard, small measurement, the 001" is about half the granularity of the metric increment. And you get a lot more splits in supplies, so you can work with drills per thou, etc... But not a woodworking thing. But it bothers me when people talk about how much more accurate metric is. Also more prone to rounding errors, which may or not accumulate.

Re: Does anyone work in metric measurements

#30

Re: Like a loony toony?

Bruce McCrory

Where' the Loony? I got a loony toon for change at the time of my intro. Our anniversary in Victoria a few years ago.

Re: Does anyone work in metric measurements

#31

Re: I'm a mutt

Bruce McCrory

I use them all. Just so you know ... A fraction of a gram (0.02 gm, 2.0 ?g, 20 mg) is a whole lot easier to comprehend than 0.0007054 ounces. Time for grains? ?? Chime in hunters.

Oh, a one-dollar bill masses at 1 gram. A jumbo size metal paper clip is 1.2x grams.

And, I'd rather see all this on a digital display, too. Oops! The agates jumped on the balance beam. No dust measurements this week.

Re: Does anyone work in metric measurements

#32

Re: I'm a mutt me too

TomD

Mutt is good, for you, crappy for the efficiency of the shop. I am a mutt or more, Bobs, suns, in a shop that is trying to go imperial, and leave those Client State measure where they belong, in Client States. I do have a grain scale that measures to a 1/10 grain.

Re: Does anyone work in metric measurements

#33

Re: Does anyone work in metric measurements

jack curtis

In my shop I get to make the rules, the main one of which is that I seldom need a numeric measure (instead using story sticks and taking measure from chisels), but when I do, it's metric, then digital imperial, then imperial.

Re: Does anyone work in metric measurements

#34

Re: Canadian problem

Guillaume Dery

Two words:

Canadian Tire

Re: Does anyone work in metric measurements

#35

Re: Canadian problem - Taps

Guillaume Dery

oops, sorry, that reply was supposed to be one up in the thread

Re: Does anyone work in metric measurements

#36

Re: Does anyone work in metric measurements

Gary Blum

Yes, I do.

My starting to work in metric was totally by accident, though. About 20 years ago I ordered a Felder combo machine which was supposed to come with metric/engllish tapes on the saw fence. It came with only the metric tapes, so I ordered new ones but they took forever to arrive. In the meantime, I thought I might as well learn to use the metric, and actually kinda liked it. Also, as a cabinetrmaker, a lot of the hardware I was starting to use was made in Europe and was metric. I never went back to the feet and inches, but even after 20 years I still do some converting in my head when visualizing lengths. But there are some very basic equivalences that help, such as 4" = about 100, etc. I memorized the cabinetmaking equivalents of 12", 24" 30", 36" and the dimensions of plywood, and that really helped. I also never speak in cm, only mm. I think that helps avoid confusion with decimal points. I only use decimals when setting up machinery with digital readouts or when using a caliper. It really helps to be able to draw your plans in metric also, so I would recommend getting a metric scale and doing any drawings in metric.

I would never say that one system is more accurate than the other; that just depends on the individual craftsman. I will say that I am very happy to have stumbled upon it and for my work, I find it much easier to use.

Re: Does anyone work in metric measurements

#37

Stephen Shepherd

No 


Re: Does anyone work in metric measurements

#38

Re: Does anyone work in metric measurements

Sgian Dubh

"I also never speak in cm, only mm."

That's good to hear because in woodworking generally the practice is the same convention as in engineering, ie metres and millimetres. Centimetres, I find, tend only to confuse the issue.

Here in the UK we are supposed to have changed over to prettu much all metric, and I use it most of the time, although we still use MPH and beer in pubs is still sold by the Imperial pint, which is a bit bigger than a US pint. I still generally initiate a design development task in feet and/or inches; for instance, I'll decide a new cabinet should be about 4' long by 20" deep, and then I convert to the nearest handy metric equivalent, eg, 1200 X 500 mm. From then onwards all the critical stages of design development through to working drawings and the following production are entirely metric.

Interestingly the younger generation, those just leaving school, tend to be pretty unfamilar with the old system of Imperial measurement, eg, inches, feet, pounds, pints, and so on. Slainte.

Re: Does anyone work in metric measurements

#39

Whatever easily works 

Re: Does anyone work in metric measurements

#40

cooking metric

Bill Tindall, E.Tn.

Exasperated with US cookbook recipes I bought a good digital scale (actually two, one for high capacity and one for more accuracy for spices and yeast). Anything I make I first convert to metric and write it in the book. Is is so much easier and precise cooking by metric weights. Get 5 people to measure a volumetric cup or flour some time. Some of our liquid volumetric measuring devices were off 10%. Never use them any more. I begged a bread recipe off a restaurant one time and I think the only way I got it was that I was happy getting the ingredient list in metric weights (which were easy to reduce by 5 to make family reasonable sized batches).

How about posting a recipe now and then......this being the Eclectic Forum?

Re: Does anyone work in metric measurements

#41

Egads! progressive drawers are even worse

Bill Tindall, E.Tn.

The standard drawer progression is the one above plus the divider. The calculations are mind numbing (5 3/16 + 7/8 = something or another) and then add the whole up to get the case opening. Then triple check the calculations, twice.

The chance for errors as so great that I have given up and do it with a pair of dividers set to the first drawer and another to the divider. My most favorite piece of furniture has a drawer off by 3/8" because of the ease of screwing up these calculations. Fortunately it is the large one and isn't very noticeable.

Re: Does anyone work in metric measurements

#42

Question for Kees

Bill Tindall, E.Tn.

In the US we have this bizarre collection of drills called "number drills" that progress from hair diameter to about 1/4 in increments that are best described as variable and arbitrary. What is the small (5mm or less) drill availability situation in Europe?

A set of these drills is handy for drilling pilot holes for one can find a drill within 0.005' or so of any size needed.

Re: Does anyone work in metric measurements

#43

Re: Egads! progressive drawers are even worse

TomD

But why would you bother with fractions, one just starts with the common dimensions, like say 4 inches, then ads increments with a dial or digital caliper, to .001". These days with the cost of calipers one could have the whole measure on one tool. How is this easier to do with milimeters. Decimal is good, no arguments there, but it is a lot easier to have a caliper around than a whole other duplication of tools supplies etc...

Re: Does anyone work in metric measurements

#44

Re: Question for Kees

Kees

Usually the smallest one is 2mm, running up in 0.1mm increments. But you can get much smaller ones.

Here is a website with a wide selection:

http://www.fine-tools.com/spiralbohrer.html

Re: Does anyone work in metric measurements

#45

Re: cooking metric

TomD

I don't see how that ads up. Seems like:

1) you are converting imperial into client state measures, so if the imperial was off, the CS is off also. I could see how recipes might be a compromise if the originals had been standardized a 3/4s this or 1/2 that and the ideal might have been something between the lines. But a lifetime of eating food tells me otherwise. Converting these kluges to metric increments would not seem to be an improvement.

2) i don't see why your metric measures are more accurate. Either in calibration, or in the user's hands. A line is a line. I'm guessing if I can hit targets, and cut dovetails, I can get near a line on a measuring cup. When reloading I have no problem dispensing powder to .1 grains (1/70000 pounds) There are even scales that do this automatically, for those with multiple thumbs. Again, even if what you said made sense, it would have long since been solved by technology. The time will come when we have devices in our brains, and can do the math for any of these systems automatically, just as the scales work automatically today. We have to understand that everything we know is like the progress that gave us the caplock rifle. Good system, lasted for like 70s years. Caplock was the height of muzzle loader tech, and as a result instantly irrelevant. Same thing with this stuff. Metric was a solution for another time that people living in that time are still clinging to. Obviously Imperial is worse, but it's like english, US approved.

3) The digital scales are a solution regardless of increment.

Re: Does anyone work in metric measurements

#46

Re: Digital Scales

William Duffield

I recently acquired a precision pocket scale from a north-of-the-border toolmonger (09A04.05) for measuring West System for very small projects. It's accurate to 0.1 gram and will also measure in several other units. It works fine with 205 fast hardener, since its ratio to 105 resin is 1:5 by volume or by weight. However, I still have to do calculations in the summer or if I'm clear coating or I have to revert to the pumps and big batches, since the density of the other West System hardeners are different. They provide fudge factors for mixing them by weight, but a calculator or slide rule is necessary to achieve maximum cure.

My family also bakes bread using two scales, one like this (for yeast, etc.) and one larger (for flour, water, etc.). With any original recipe and the measuring cups used for that recipe, it is easy to convert to the weighed method. After conversion, if a different size batch is needed, a simple spreadsheet conversion is easy and reliable. The precision or the weight of the original measuring devices is no longer important. Nor is the unit of measure, since you can choose from any one of several units when you first use the scales to convert the recipe.

Re: Does anyone work in metric measurements

#47

Yes but.......

david charlesworth

I am very bad and use all sorts of units acquired in my youth, as the mood takes me.

Imperial seems good for larger furniture measurements. 6 foot, twenty nine inches for table height etc. but surely life is too short to be thinking about 29/64" ??

Millimetres do a fine job from 0.2 to 30 mm, but for shaving thickness I prefer thousandth's of an inch, units which were familiar in my model engineering days. For some unknown reason I never use tenths of an inch.

best wishes,

David Charlesworth

Re: Does anyone work in metric measurements

#49

And then there is Whitechapel and Bob's rules

Bill Tindall, E.Tn.

These are ruled in 1/12ths inch. Actually makes a lot of sense and I have such a ruler.......but never use it. I have a metric tape and use it to divide things. Thanks for the response.

Re: Does anyone work in metric measurements

#50

Oh, so not so.....

Bill Tindall, E.Tn.

"Caplock was the height of muzzle loader tech".

It will be hard to be restrained on this topic for I am somewhere east of where Warren is on hand tools when it comes to muzzle loaders. The new ones are rifled for saboted low ballistic coefficient expanding nose projectiles and employ inline high intensity ignition (necessary to ignite the phony black powder used in them). Add the stainless steel barrel, 1.5 x 7 scope, plastic camo stock (camo stock and bright stainless steel barrel ???).....I must stop.

I look at the "muzzleloader" section of the gun stores and don't recognize most of what is displayed.