New WoodChat!
Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Want Better Milling & Firewood Knowledge?

More scrap = improved finger jig....

Posts

More scrap = improved finger jig....

#1

More scrap = improved finger jig....

roger lance

I've been gradually improving various jigs in the shop....and my new table saw sled was so successful that I decided to make a finger joint jig in much the same style....and the scrap pile provided the parts. I use hard maple for the runners and my tip on jig making in this tread has to do with making tiny rabbets along the length of the runners....


once the jig base is screwed to these runners, the runners will usually expand and not move smoothly in the saw miter slots....the rabbets allow for trimming with a shoulder plane (and you thought this had nothing to do with hand tools)....simply move the jig back and forth on the saw and the runners will burnish revealing where to trim....


Now some pictures of the jig should take the place of a lot of words....




and a test cut....close....enough room in there for glue and some expansion.....


thanks for looking.

Re: More scrap = improved finger jig....

#2

Finger joints in shop boxes....

roger lance

Just looking around the shop for examples of finger joints and have a box fashioned after one by Freud for shaper cutters....so heres my interpretation of their idea....



handy joint to use in and out of the shop.

Re: More scrap = improved finger jig....

#3

A finger joint box for saw blades.....

roger lance

Another example of a box for the shop using finger joints is this saw blade storage box I made years ago based on one in FWW....



there are other examples that show this joinery in shop storage solutions....a good jig is worth having to make these items.

Re: More scrap = improved finger jig....

#4

Nice

Tony-Memphis

Brings back memories. When I first started woodworking, one of my first projects was a box jointed box for router bits. I used oak pallet wood I brought home from work. It is one ugly box, but I learned a little and it served me (and my bits) well. I'd like to take the time to build a similar jig to yours. Very useful indeed.

Tony

Re: More scrap = improved finger jig....

#5

Re: More scrap = improved finger jig....

eliot d

I'm sorry to be so dense, but I need to know a bit more, please. Where , exactly do the tiny slots fit into the table saw or sled? The picture with the shoulder plane looks to me that one could do this operation even if the runners didn't have the tiny rabbets. what am I missing? (I have always just scraped along the side of the runner with a chisel --sort of like using a narrow card scraper;that always worked.) Also, I tend to use those more-or-less clear plastic runners that you can easily get. They seem to be more dimensionally stable than wood.

Re: More scrap = improved finger jig....

#6

Re: More scrap = improved finger jig....

roger lance

Eliot....the best woodworking tip I can give you is that there is no "The Way" of doing anything....there are always a multitude of ways....this is but a way.....if you have access to the plastic runners and like them, then continue with them....I have hard maple scraps so I use those.....the little rabbets are cut on a tablesaw in mere seconds and it is a practice I got into along the years.....nothing sacred here....it just offers a little bit of relief against the bottom of the jig so that you aren't leaving a high spot....you'd accomplish the same thing by chamfering the edges of a runner that goes against the jig bottom with a block plane.....and there is nothing sacred about this jig design either.....theres a bunch of designs out there....I was hoping that other people would share theirs.

Re: More scrap = improved finger jig....

#7

Re: More scrap = improved finger jig....

eliot d

O.K. , thanks again. I don't always have plastic runners around, so I do like the idea of using hardwood. It's taken me a while to figure out just which way the runners you describe are positioned: it can't be up into the sled -- it would be lost up there. So they're obviously facing down into the table saw slots. Now, you say the runners often start to bind after you screw them it. That must come about about because the screws entering the runner expand the width of the runner a bit. (Hence, those little rabbets provide some relief. )But I would think that the part of the runner that is above ( closer to the sled bottom -- up from the table saw slot bottom) the rabbet could still expand. The answer may be to drill a large enough hole in the runner before putting in the screws or to just use glue. You also say that one could just as easily use a block plane to chamfer the bottom edges of the runners. That would indicate that you believe or know that the binding occurs where the bottom edge of the runners meets some part of the table saw slot. But that wouldn't be the case in table saws with keyhole-type slots, would it? Am I still missing something? I hope I haven't made too much of all this. I got interested because I want to make some box joints using a nice sled like yours. You clearly are a careful worker.

Re: More scrap = improved finger jig....

#8

Re: More scrap = improved finger jig....

roger lance

Yes....lol.....you are missing something. The little rabbets or chamfered edge is placed against the bottom of the sled....they are not directed down to the bottom of the tablesaw miter slots. This is just a little technique that allows planeing, scraping, or sanding of the runner in place without removing it from the sled to get at the spots that bind. So when I place the sled on the saw, I can see the little rabbets on the ends of the runners. Also, I place the runners in the table saw slots and position the sled base on top of them and then screw the base to the runners.....which assures alignment. First I lay out the placement for screws in the base....drill the holes....then realign the base with the runners in the saw slots and transfer the screw locations to the runners which are then drilled in preparation for the screws. then place the runners back in the slots....realign the base and then screw the base to the runners. The introduction of screws into a 3/4" wide by 3/8" thick piece of wood causes the sides of the runner to expand against the sides of the tablesaw slots.....and you get binding which is what I'm removing with the shoulder plane. I would not recommend gluing the runners to the base as you may want to remove a runner at some point. The best teacher is experience.....try looking for box joint videos on youtube.....then make one.....a simple one....then work with it.....see how you do.....your level of knowledge and understanding will greatly increase.

Re: More scrap = improved finger jig....

#9

Re: More scrap = improved finger jig....

eliot d

Oh my! Got it now ( I think): with the runner spaced a little bit from the bottom of the sled because of the little rabbets or chamfers, the shoulder plane blade has access to the entire thickness of the runner, right? (Isn't there a kind of plane where the blade goes all the way to the edge of the sole of the plane? Would that work without the rabbets or chamfer?

I just thought of something else: I made a really strong, square, crosscut sled way back. I wonder why I couldn't clamp on an auxiliary backing board with the proper spacing block for the finger on that?

Re: More scrap = improved finger jig....

#10

Re: More scrap = improved finger jig....

roger lance

Yes....you've got it....I started making these small rabbets before I got a nice LV shoulder plane....use to trim with a scraper.....just a little trick is all.....I'd keep the table sled you have for its intended purpose.....remember you are going to make these finger joint cuts with a dado and that leaves a wide opening in your sled which you will probably not want.....make a separate box joint jig.....youtube has many videos.

Re: More scrap = improved finger jig....

#11

Re: More scrap = improved finger jig....

William Duffield

You're right, Eliot, you shouldn't need the little rabbets if you use a shoulder plane, and it is a shoulder plane that Roger is using in the picture at the top of the thread. The same goes for rabbet planes. However, the rabbets make the tuning of the plane a bit less critical, because you don't need to worry nearly as much about the exposure of the blade on the side of the plane.

Another advantage of rabbets on all sorts of jigs (fences and stop blocks, especially) where they meet the surface of your machine is that they provide some relief for sawdust, so you don't have to keep your air compressor nozzle at hand to clean them out after every cut, to insure the accuracy of your cuts. One chip between the fence and the stock can throw off the cut, but lots of chips can accumulate in the rabbet before they keep the stock from accurately contacting the fence or stop block.

Re: More scrap = improved finger jig....

#12

Re: More scrap = improved finger jig....

eliot d

Wow,subtlety on top of subtlety! There certainly are some very fine woodworkers around here!

Re: More scrap = improved finger jig....

#13

Re: More scrap = improved finger jig....

eliot d

Hi Roger. Well, I made one very similar to yours and I did use your tiny rabbet trick. It worked wonderfully! BUT... I believe I made mine a bit on the light side. So when I used it for the first time , even though the fingers came together just right side-to side, I found small errors in the perpendicular direction. Those errors, I'm sure, came about because the whole jig lifted a tiny bit during the cuts, thereby causing some variation in the length of the fingers. I'll go back and add some length and weigh to it. Thanks again.

Re: More scrap = improved finger jig....

#14

Re: More scrap = improved finger jig....

roger lance

Eliot....You're welcome.....glad to hear you've made a jig.....work with it awhile.....making some adjustment is normal....good luck on the projects to come.