New WoodChat!
Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

A55 Smoothing Plane

gluing up panels wider than your planer

Posts

Re: gluing up panels wider than your planer

#26

Cauls and more cauls

Derek Cohen (in Perth, Australia)

My panels are butt jointed. No biscuits or dowels. I add a spring joint, run a layer of blue tape along the clamp to prevent glue attaching to the steel, add glue and bring them together.

I keep the face side up where I can see the joins and be in a position to adjust them with a rubber-headed mallet. Now the boards, if used for a table top, may not be the same thickness. Thickness does not matter in this situation - it cannot be seen in the final piece - but it does make glueing up tricky. The answer is to add several cauls to ensure the face side is flat and does not move while drying.

Below is the underside of a table with an oddment of thicknesses. Only the edges are the same thickness.



Regards from Perth

Derek

Re: gluing up panels wider than your planer

#27

Jack Guzman from Maine

Re: Pipe clamps

Jack Guzman from Maine

Yellow glue,white glue,liquid hide,the procedure is the same . I use all three at one time or other. I usually prefer yellow glue for panel glue-ups because I can take the clamps off sooner.---Jack

Re: gluing up panels wider than your planer

#28

What?

Bill Tindall

"Below is the underside of a table with an oddment of thicknesses"

What kind of planer did you buy that can't hold a constant thickness? Don't they have Delta and Powermatic in AU?:D

Re: gluing up panels wider than your planer

#29

Iron stain prevention

Bill Tindall

Just lay a layer of news paper oven the clamps. I keep a pile of news papers in the shop for gluing. They go on the bench, on the clamps.

Do people still use pipe clamps? They flex too much. I started with them but they got replaced quickly with I-beam style clamps.

I am mystified that no foreign manufacturer has offered a knockoff for the traditional Hargrave bar clamp to be found almost universally in old shops.

Re: gluing up panels wider than your planer

#30

more what!

Bill Tindall

What happened to my smiley face ? all I got was a :D.

Re: gluing up panels wider than your planer

#31

Need a space

John in NM

:D

Without a space in front it looks like this--->:D

Re: gluing up panels wider than your planer

#33

planer v sander

Jerry Gibbs

I would hesitate to send a glued panel through a planer. The risk of tear out is too great. If the panel still needs leveling after gluing, and you are not confident with a hand plane to level a large panel (like me), I would find a cabinet shop with a wide belt sander and pay them. Jerry

Re: gluing up panels wider than your planer

#34

I routinely power plane assembled panels

Bill Tindall

The lumber for assembling panels is typically already planed, more or less. I keep track of what direction it went through as well as what direction I intend to use it. So long as the orientation of the individual boards remains the same as in the panel there is little risk planing the glued up panel. I, and most others that own a wide machine, plane panels routinely.

My panel preparation procedure (which doesn't belong on this Forum) is to glue up skip dressed boards into panels something less than my machine width. These are then finish planed to required thickness.

My machine is 18" wide. Furniture tops are often a bit more. I plane the skip dressed panel to desired thickness along with the additional board as needed to make the required panel width. Then I make the last joint with the finished planed parts to get the required panel width. Only one joint needs to be leveled by hand for say a 22" wide top. Its quick and that is the goal.

Re: gluing up panels wider than your planer

#35

Re: I routinely power plane assembled panels

TomD

That is how I do it also. Though there is the flip side where the wood is very fragile and does not plane safely. This just gets worse when the direction has to be compromised, if at all, when making up full panels. If one is making stuff like shaker furniture with bland wood, or a bench where the wood is selected functionally it probably isn't a problem. But some wild grain table, think Nakashima is another mater. Break out the router sled jig, and the belt sander.

Re: gluing up panels wider than your planer

#36

You are making this routine task more complicated.

Bill Tindall

..than it needs to be. The potential benefit of all the proposed crutches-cauls, splines, biscuits, etc. is that they may compensate for lack of a modest amount of practice, experience and care. These crutches are unnecessary if you are willing to invest in a bit of practice and care. If not, don't read on.

What follows is what almost everyone that makes panels does. I have assembled thousands so this advice is not theoretical. Practice making one joint from 2 boards.

1, Spread the clamps across the bench as shown in someone's picture they provided as well as all the other advice offered.

2. Lay down the two boards and snug the clamps. Examine where the joint is high or low so you can anticipate this situation when actually gluing. In fact it may be useful practicing making a perfect dry joint.

3. Disassemble and apply glue. Some apply to one surface, others to both. Good arguments can be made for each choice.

4 .Put boards back on the clamp and slowly snug the middle clamp while coaxing the boards into alignment in the middle. Only finger pressure is necessary. At this pint the ends of the boards have not been brought together to where they tack.

5. **** With your fingers press the joint into alignment at one end and snug this end clamp. Repeat at other end. If the boards are flat on the face against the clamps the joint will be aligned.

6. Steps 4 and 5 may be repeated as the clamps are snugged ever more to get finally get tack. If an ends remains out of alignment mash it together with a clamp. It will easily shear for the first couple of minutes.

If I might make a guess I think you may be hurrying the clamping process and not coaxing edges into alignment and keeping them there while SLOWLY applying the clamp pressure among the clamps. I probably diddle with the clamp pressure a half dozen times while assembling a panel.

Re: gluing up panels wider than your planer

#37

Not only that...

James Watriss

During the clamping of a panel:

-You want to be able to SEE that all of the gaps have closed.

-You want to watch the panel, to see if it's flexing. If it is, that could be bad clamp alignment, or other issues that will cause the finished panel to not be flat.

-You want to be able to see that the finished panel will turn out well. In my experience, the more force that's required to strangle everything into position, the more trouble the finished part will be when the clamps come off.

Curved cauls are good for edge banding plywood, not for edge jointing solid wood.

Clamping panels isn't rocket science. Some skill and practice does help. Dry clamping is a huge help, because with a properly sprung joint, you can clamp the whole thing with one clamp, hold it up, and inspect it to make sure it's a good joint. I don't do this on huge panels all the time, but if the dry clamped panel is flat and good, that's an indication that the end result will be good.

Spend your time and effort on developing your own skill level, not on building crutches to compensate. You spend the same amount of time and effort in the short term, and you realize the benefits of skill in the long term.

That said, if some of the boards are bowed, the dry clamp is that hairy, and it's one of those stupid projects that just has to get done... Get a doweling jig, or use wire nails, clipped close to the surface, to help hold the alignment when you do the glue up.