New WoodChat!
Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Premium Live Edge Slabs, Hand-Selected in the Berkshires. Shop Unique Hardwood Pieces.

Taking advantage of a warm day in Oct.

Posts

Taking advantage of a warm day in Oct.

#1

Taking advantage of a warm day in Oct.

Bill Tindall


The finish schedule is sand to 180, stain with 12% burnt umber mineral pigment in linseed oil, seal with thinned alkyd varnish, scuff sand with 400 grit and top coat with thinned alkyd varnish. I avoided building up a thick finish by thinning the varnish.

The push was on to get the large pieces finished before cold weather. I can do the drawers which are smaller when it is colder as they can be moved indoors to cure.

Re: Taking advantage of a warm day in Oct.

#2

Nice

Bill Houghton, Sebastopol, CA

That's going to be one of those pieces that trap people into looking at the grain...then the design...and before they know it, they'll have been looking at the furniture for ten minutes.

Re: Taking advantage of a warm day in Oct.

#3

Re: Nice

Bill Tindall

Out of the bright sun the top is not so nearly "in your face" and that is good. The plan is to do line and berry on the drawers. If successful it won't be the top that gains attention.

Re: Taking advantage of a warm day in Oct.

#4

You wouldn't be spraying finish where we are

Ron in Sterling, CT

Hi Bill,

We are on vacation in Michigan, and temps here have been in the 40's and 50's with lots of rain -- not good weather to spray finish.

By the way, the piece is coming along great. Looks good so far, and can't wait to see the finished product.

Ron

Re: Taking advantage of a warm day in Oct.

#5

Re: Nice

Bill Houghton, Sebastopol, CA

"If successful it won't be the top that gains attention."

But it's lovely to have a piece on which even the less attention-getting parts are worthy of attention. Some of the furniture we inherited from my grandmother - factory furniture, at that - is worth looking at multiple times, to find new little joys each time.

Re: Taking advantage of a warm day in Oct.

#6

Re: You wouldn't be spraying finish where we are

roger lance

Ron....Welcome to Michigan.....you missed the good weather by a week or so.....in Grand Rapids we're hoping to get back to dry and 60* tomorrow or Tuesday.....have a great time in the Great Lakes state!

Re: Taking advantage of a warm day in Oct.

#7

We Have had a Great Time

Ron in Sterling, CT

Roger,

It has been an enjoyable week, even with the inclement weather. We attended my 55th High School Reunion Banquet last night. Headed back to CT tomorrow.

Ron

Re: Taking advantage of a warm day in Oct.

#8

The mouldings

Wiley Horne--So. Calif.

Hi Bill,

I'm much taken by the mouldings which are in view in the photo. Do you mind showing closeups (sometime when you have a chance--I know you're busy) of the top and bottom mouldings on that side? Are the top and bottom symmetrical--I can't quite make out. Also, the mould that sets off and encloses the side panel--what is it? An ogee? Or a quarter-round stuck with an applied bead?

Most handsome!

Wiley....wondering also what is the preferred spelling of molding/moulding

Re: Taking advantage of a warm day in Oct.

#9

Re: The mouldings

Bill Tindall

Will get back with close ups in a bit. Unfortunately I have moved the case from a brightly lit finishing location to a dim lit place awaiting the drawers to be finished. This molding is just a slightly shrunk version of what is on an earlier chest which in in good lighting so I may just picture(invention of new verb)the larger version.

The pattern is taken from a Chester Co piece located in Winterthur, a piece judged by some to be the best of the Chester Co stuff that survives. In any case I like this molding better than what I have seen on other Chester Co stuff, which is less "refined" molding in my opinion. Unfortunately there is no router cutter that comes close so I wasted it out with a saw blade, then scraped to the final shapes. The process is far less tedious than making 5 drawers.