New WoodChat!
Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Abingdon, VA – Tree Cutting & Portable Sawmill

Another bench appliance

Posts

Another bench appliance

#1

Another bench appliance

Ron Harper

Dovetail paring jig is next on the list


img

Re: Another bench appliance

#2

You got your Moxon !!

roger lance

Ron.....congratulations on finishing the Moxon.....hope you get a lot of years of great service from it.....I've really been liking your recent shop photos.

Re: Another bench appliance

#3

Nice work

Bill Houghton, Sebastopol, CA

What are the screws? Did you use veneer press screws or some such?

You might consider a steel or brass washer under the handles on your screws to reduce wear on the wood (maybe there's already one there and I can't see it).

Re: Another bench appliance

#4

Bill i am lookin

Ron Harper

I do want brass washers. Yes.. Veneer press screws form Rockler.

Re: Another bench appliance

#5

Re: Bill i am lookin

Bill Houghton, Sebastopol, CA

Rockler says the screws are 11/16" in diameter (maybe they're metric, and actually 17mm). This is an odd size by modern (inch) fractional standards. You might be able to get 5/8" washers and file out the hole a little. This is not as bad as it sounds - washers tend to have oversized holes, to make installation easier; McMaster-Carr lists its 5/8" washers as having a 0.68" inner diameter; and 11/16" is just 0.6875", so you'd have only a little filing to do.

I'll have a look next time I'm at my fairly-well-stocked hardware store.

Re: Another bench appliance

#6

Dovetail paring jig

Derek Cohen (in Perth, Australia)

Hi Ron

That Moxon vise looks excellent. Now we want to see examples of it in use! :)

Regarding the dovetail paring jig you mentioned, there are two on my website. Very useful, especially for baselines of pins which can stretch out. Of course, once you are more practiced a simple undercut at the baseline can enable clean and straight edges there.

A block of wood clamped over the edge of the baseline works well. Adding bolts makes this more versatile.


Here is a link to the first jig I built: http://www.inthewoodshop.com/ShopMadeTools/AJigforParingDovetailBaselines.html

Regards from Perth

Derek

Re: Another bench appliance

#7

If you can`t find them locally...

Bob Hackett

Email me with the major diameter of the press screws you`re using. I may have some heavy marine grade bronze washers I can bore to fit.

Re: Another bench appliance

#8

Re: Dovetail paring jig

Ron Harper

Derek

I had one of these over ten years ago. I have no idea what happened to it. I do remember very well that the quality of my dovetails went up when I used it. I am not particularly a fan of undercutting. I think working to dead square is better practice.

Again, thank you so much for being so willing to share your learnings from your experience.

Ron

Re: Another bench appliance

#10

Re: Undercutting the baseline

Patrick Gibbons

Thanks for clarifying Derek. I misconstrued your meaning until you posted this.

Re: Another bench appliance

#11

Now I am with you


Re: Another bench appliance

#12

My hardware store failed me (and you)

Bill Houghton, Sebastopol, CA

Their brass washers stop at 1/2". Bob Hackett's offer is a very generous one, though; maybe that will be your solution.

Re: Another bench appliance

#13

Re: Bill i am lookin

William Duffield

If you had used my methodology, you would not have needed brass washers, you would have saved substantial outlay for hardware, and you would have found everything you needed at your nearest Borg or Ace (a real hardware store), for about $11.