We value your privacy.
We use cookies to enhance your browsing experience, analyse site traffic, and personalise content.
By clicking “Accept all”, you consent to our use of cookies. You can also choose
“Essential only” or learn more.
A woodworker friend directed me to this entertaining contribution to woodworking from "down under". I found the Pegs and Tails site both entertaining and informative, and well, astounding. The author apparently builds stuff outside, and very nice stuff at that. He talks about taking the tarp off to work when the weather is fair.
Most interesting was his report of fine mahogany now coming from former British plantations in the Pacific islands.
Interesting. I will have to have a look. I like the aust. shed vibe. I like the way they build boats, and am currently working on a trailerable tri from down there. Most of my boatbuuilding involves some outdoor work, it`s a lot nicer than being indoors.
I enjoy his blog, especially his histories and his studies of furniture forms. The contrast between the British view and our Colonial view is enlightening. He also does good work. I just wish he showed more of his tools and process.
I would almost bet his name is not really "Jack", and I doubt that this link to the "Lemon Studio" shows his real shop and work bench. In one of his posts, I did find a photo of a jack plane with a Hock iron, on a real work bench with a vise and dog holes (and it included a great tip for aligning pin and tail boards for marking out dovetails, that I think I can adapt to my setup). When I lived in Florida, I had a Bearss lemon right outside the overhead door to my shop, but it's gone now.
I am glad someone mentioned Pegs & Tails, it's one of my favorite sites and practically my first stop every morning during coffee. I enjoy watching his projects unfold, his humor and selection of topics, and writing style. I am always able to find something new and interesting there.
I love his blog entry "Mid-Eighteenth Century Drawers." Super good stuff there without a doubt. Nice workmanship with a bare minimum of fuss and gimmick.
Best quote from his dovetailing blog entry with which I couldn't agree more:
"I am not a follower of the banal and verbose tutorials on cabinetmaking basics to be found on the internet, but I believe following the making of an eighteenth-century style drawer (in this case, the № 3 drawer for the circa 1755 George II Virginia Walnut Chest of Drawers) to be pertinent here..."
And of course he follows the whole affair with a perfectly constructed drawer.
....in response to the current "flaunt you dovetails" fashion...
"Dovetails were not viewed with the same aesthetic in the eighteenth-century as they are nowadays"
And then he proceeds to cover them up with cock bead and facing strips for the chest of drawers he is building, of which I am smitten and will likely recreate. I like the feet.
dividers vs blades, what seems to be a different -
Bill Tindall
- nomenclature. Some time ago were were lectured that "blades" are the horizontal components that separate drawers while "dividers" are vertical separators. Yet this author, who seems well researched, uses dividers as the name for the horizontal separators.
Anybody have any additional opinions on this nomenclature?
Thanks Bill! Very meaty site. Lots to study and think about.
Somebody please help me, as I'm kinda slow today. I can't figure out why he terminated the bottom of the drawer side using a half-tail (rather than a half-pin). What are the advantages/disadvantages one way versus the other?
Re: dividers vs blades, what seems to be a differe
William Duffield
The nomenclature of these replaceable drawer supports can certainly be confusing, and often even contradictory, even within the same shop and even within the same construction book. Sometimes it depends on where you were in the milling process and even on how many rows of drawers you were installing in the case. We called them "slides" and "guides," the slides being the members that supported the drawer gravitationally, but when fitting the height of the drawer, they sometimes were referred to as kickers and runners, the kicker being the slide above the drawer and the runner being the slide, or slide assembly below the drawer. Of course, the kicker for one drawer was the runner for the drawer above it. Of course, it partially depended on how the case was constructed and whether we nailed the guide to the side of the cabinet and nailed the slide to the side of the guide, or mortised the slide into the drawer blade (a.k.a. divider) and glued or nailed the guide to the top of it. Variations in construction techniques, and therefore nomenclature is extremely variable.
I have two books by Bill Hylton, Illustrated Cabinetmaking and Country Pine, which are very helpful, but even they don't help a lot with consistency.
Re: dividers vs blades, what seems to be a differe
Sgian Dubh
Yes Bill. What you call 'blades' have always been called dividers around all the workshops I've worked in-- in fact the first time I saw you use the word blade in a description of something you were making I hadn't got a clue what you were going on about.
Then there's runners and kickers, and as William said in another post, runners are below the drawer, and the kickers are above and both engage with one edge or another of the drawer sides. Therefore in many cases some runners are also kickers, and some kickers are also runners.
As to what's on the bottom edge of the drawer side where it runs on the runner, it's called the 'bottom edge', the glide, slide or slip depending on configuration and local custom. Slainte.
So where did this "blades" thing come from? First I ever heard about it was here on WC. And then in some post I call the things between drawers "dividers" and got a lecture from someone, I think down under or at least across the pond, that dividers were the vertical parts and it should be "blades". Not wishing to appear even more ignorant I adapted what seemed to be a reasonable nomenclature. Then I encounter someone from down under as well as across the pond calling these things "dividers". My chest of drawers project is at a standstill until I am sure about what part I am about to dovetail!
The sides are not grooved to receive the drawer bottom. They're thinner, lighter, and more elegant than a clunky drawer side thick enough to take a groove. The bottoms fits into slips glued onto the sides which also provides more surface for the drawer to run on. The drawer front, which is thick, is grooved to receive the bottom.
All this FWIW and unless I'm missing something more obvious (always a possibility).
In the introductory paragraph he mentions "two changes (a 90° rotation of the drawer bottoms and a minor change to the front bottom dovetail)" as occurring after 1725. I think the addition of a half pin at the bottom is the second change.
The drawer he constructs uses a half pin at the bottom. I think the half tail was an improvement over the 17th century practice of letting the drawer bottom show from the side and the half tail was a further refinement.
My understanding of the drawer construction was that the drawer side was rabbetted and the bottom fit into the rabbit , then a runner nailed onto the drawer bottom and planed smooth with the side. I have seen antique English drawers made this way. Alan Batty, English tradesman, described this construction to me as what was done in the factory he worked in making drawers. I prefer slips, as you describe.
Green, American Furniture 18th Century page 131, 2nd example. I think the answer to your question is that is the way it was done then. As I understood the description he is making a drawer just like example #2.
While I am on the topic, I think this is one of the best books I have found on construction techniques for quality traditional furniture.
Absolutely. If you are surrounded by people who have cut a few thousand sets, it's no big deal. And that is probably where we are headed today now that most people either consider it basic or something that anyone can do but they just haven't got around to.
Thanks very much, Charles, Bill, and Steve! I finally see.
It's all about the rebate to let in the bottom and glide. The half-tail makes a neat joint, whereas a pin down there would introduce a number of problems (which aren't worth going into).