New WoodChat!
Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Rare Exotic & Domestic Hardwoods, Milled In-House in Oregon. Browse Unique Stock.

Leg vise Parallel Guide Adjuster by Ancora Yacht S

Posts

Leg vise Parallel Guide Adjuster by Ancora Yacht S

#1

Leg vise Parallel Guide Adjuster by Ancora Yacht S

Derek Cohen (in Perth, Australia)

For the past few months I have been discussing a parallel guide adjuster designed by Jim Ritter. My input has largely been devil's advocate while Jim sharpened up the design for production. I have no interest in this venture other than wanting to see a good product made available for others to use.

The leg vise parallel guide adjuster is an alternative to the St Peter's Cross, both of which enable a leg vise to function without the pin adjuster. No more stooping and setting the parallel guide for a specific width. Instead there is a single setting for all work pieces. In theory there should also be more pressure as the chop is more upright.

Yesterday I completed assembling the pre-production kit, and here are a few pics with my impressions.

From the front you will not notice any change to my leg vise ..


Close up you may note that I have replaced the steel screws with brass .. :)


From the side you will see a solid parallel guide and, above it, a chain ..


Solid paralel guide?!

Yeah .. in for a penny, in for a pound ... off came the parallel guide of my 6-month old leg vise ..


.. and replaced with this new, hole-less version ..


Inside the bench the chain mechanism can be seen ...


Outside ..


In all, including building a new parallel guide (which I do not expect others to do), the installation took a day.

So how does it work?

It grips ...


... and grips ...


.. and continues to grip ..


.. no matter how little there is to grip ..


Downside? The mechanism requires that the internal wheel guide is removed .. this one ..


As a result, there is a little more resistance in the parallel guide moving back-and-forth compared to before. The chop still moves smoothly, and the effort is similar to that of the Record #52 1/2 I had on my old bench. Of course, this may just reflect the need for a little fine tuning since the parallel guide is new. As it stands, this is a rejuvenated vise, one that promises to work with a much greater range and considerably less effort.

Once Jim gives the OK I will post a pictorial of how I installed the kit.

Regards from Perth

Derek

Re: Leg vise Parallel Guide Adjuster by Ancora Yacht S

#2

Re: Leg vise Parallel Guide Adjuster by Ancora Yac

roger lance

Derek....I have seen this chain modification on other forums and it looks very promising....I can understand how it would work when opening the vise as there is a pulling of the chain....but I'm not as clear when closing the vise as this would be like trying to push a rope.....do you have to place a little knee pressure on the bottom of the chop when closing/tightening the vise ??....great job as always on your presentation.....an interesting advancement.

Re: Leg vise Parallel Guide Adjuster by Ancora Yacht S

#3

Re: Leg vise Parallel Guide Adjuster by Ancora Yac

William Duffield

Hey, I could cannibalize my Veritas Twin Screw vise! ;) It's got the screw, it's got the sprockets, and it's got the chain. But, that would probably hurt more than the surgery you did to your leg vise.

Re: Leg vise Parallel Guide Adjuster by Ancora Yacht S

#4

What about...

Bob Hackett

A wheel that would fit in a recess behind the sprocket held by a captive axle bored thru the leg and capped with the same type of wood caps wood (and brass screws, a nice touch) you used for the garter? Any slack could be taken up by by adjusting the wheel in front.

Re: Leg vise Parallel Guide Adjuster by Ancora Yacht S

#5

Re: Leg vise Parallel Guide Adjuster by Ancora Yac

Derek Cohen (in Perth, Australia)

I can understand how it would work when opening the vise as there is a pulling of the chain....but I'm not as clear when closing the vise as this would be like trying to push a rope.....do you have to place a little knee pressure on the bottom of the chop when closing/tightening the vise ??


Hi Roger

As the chop moves inward, the end of the parallel guide moves away, tensioning the chain.

As the chop moves out, the connection in the chop pulls the chain, again tensioning the chain.

So the chain is constantly in tension, and (having tuned the amount of tension during the installation phase) the parallel guide and chop will be balanced.

No knee pressure is necessary. It all works smoothly. :)

Regards from Perth

Derek

Re: Leg vise Parallel Guide Adjuster by Ancora Yacht S

#6

Re: What about...

Derek Cohen (in Perth, Australia)

Hi Bob

Sounds like one of the ideas I pitched to Jim! :) He replied, "The way I understand the upper roller, it's function is taken over by the chain. The chain will not let the beam swing up past horizontal because then the jaws would be out of parallel".

I have a little more tuning to do, and will report back. Please note that my earlier comments were about the relative resistance when the roller was removed. With the roller (before the chain), I could spin the screw in effortlessly. It would continue to rotate on its own momentum. Now, with the chain in place, the momentum is no longer there. Nevertheless, the screw turns easily.

Regards from Perth

Derek

Re: Leg vise Parallel Guide Adjuster by Ancora Yacht S

#7

Re: Leg vise Parallel Guide Adjuster by Ancora Yac

roger lance

Then Jim has a good design....and I wish him success....it will be interesting to see some direct comparisons with the St Peter's Cross when they become available.

Re: Leg vise Parallel Guide Adjuster by Ancora Yacht S

#8

Re: Leg vise Parallel Guide Adjuster by Ancora Yac

Curt Putnam

... and the Hovarter vise. I wish someone would buy one and review it.

Re: Leg vise Parallel Guide Adjuster by Ancora Yacht S

#9

My goodness

Bill Houghton, Sebastopol, CA

My grandfather, whose bench (and thus leg vise) I inherited, would be shaking his head with wonderment. His leg vise doesn't even have a garter on the screw, just a big brass washer.

That's a pretty neat design.