New WoodChat!
Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Nearly 100 Exotic Wood Species, Direct-Imported Since 1972. Shop Slabs & Turning Stock.

wood drying

Posts

wood drying

#1

Jack Guzman from Maine

wood drying

Jack Guzman from Maine

One part of chairmaking that I'm still learning is the drying of certain pieces for different reasons.The legs are best turned green but the tenon needs to be dry or it will shrink after assembly. Also the spindles should be shaved while green but need drying before final tenon sizing. It was suggested that the best way to see if the wood was dry enough was to weigh it. When it stops losing weight,it's dry. My wife loaned me a scale she uses for baking,but I need one I can keep in my shop.(or she may not get hers back)Anyone have any ideas for a proper scale? Where to find one?I have a small kiln built of foil backed insulation board with high wattage light bulbs for heat.I use a thermal switch to keep the heat at about 120.Any ideas on how long in general it takes to dry a small item in a kiln such as mine?The woods are maple and red oak.---Jack

Re: wood drying

#2

Buchannan video?

Bill Tindall

I would have thought this topic would have been covered by Curtis. He sticks the ends of his tenons in hot sand for a while. It has been a long time since I watched him do this part so I don't remember the time, but it should be quick and the hot dried wood takes on different desirable properties after this hot treatment.

The rest of your questions can not be answered for lack of data. Drying rate depends most on temperature, air circulation and humidity of hot air. At 200 degrees with good air circulation a spindle would be dried in an hour or less.

The cooking store will have a suitable scale. Drying to constant weight is no more than that. The wood has reached as dry as it will get......for the conditions used. Without knowing the humidity for these conditions the moisture content of the wood can not be predicted.

Re: wood drying

#3

Another good source of information like this is

Bob Hackett

John Alexander`s book, Make a Chair from a Tree.

He talks about the joints required to hold these chairs together in depth and also gives detailed explanations of how certain areas of different parts of the joint(and even different areas of the same part) need have different moisture contents and why this is so.

In the few pieces of furniture (both indoor and outdoor) that I made using post and rung construction I made just the tenon areas of the spindles very dry and left the rest of the spindles alone. The posts (and their sockets) remained relatively wet. The residual moisture in the spindle combined with the moisture in the post re-infused the dry tenon and when everything reached the same moisture level the joints were in fact locked and the really well fit joints probably didn`t even need glue.

Alexander goes into more depth about these joints and even small details like optimal grain orientation during assembly. There are details involving wood and the nature of wood movement that Alexander points out that I haven`t found in other books. I highly recommend this book to anyone building post and rung furniture, regardless of skill level.

Re: wood drying

#4

Re: Another good source of information like this i

TomD

There are a lot of woods that if you throw them in a hot box will not survive. Real kiln drying involves steps like steam. If you turn a piece of wood with normal spindle confirmation, then you shouldn't have to wait long for it to dry anyway since you are exposing a lot of endgrain and reducing some of the splitting stresses. All you have to do is get one cycle up on natural drying, and all you have all the wood you need. If you push the drying you have to deal with all that technical clutter for ever.

As far as wood joints etc... Are concerned, the Dunbar system, last time I heard to described was not based on differential wood shrinkage.

I would recommend the Alexander video over the book. Though I like the book a lot. But the video is more up to date.

Re: wood drying

#5

Jack Guzman from Maine

Re: Buchannan video?

Jack Guzman from Maine

I got what I know now from Buchanan's video as well as books by Dunbar and Rendl. They give plenty of info but no general idea of time to dry.I know my info is vague but what I'm interested in is it a matter of days or does it take weeks?

However,I can figure that out by drying by weight. My main question was and still is what kind of scale should I look for? ---Thanks---Jack

Re: wood drying

#6

Re: Buchannan video?

Bill Tindall

in is it a matter of days or does it take weeks?.......minutes in hot sand. Moisture transport out the end grain is about 10X across grain, so it is very fast drying the tenons.

. My main question was and still is what kind of scale should I look for? Repeat.....go to kitchen store. Any scale you find there will be suitable but if you want metrics you need to detect a 1% change in the weight of what ever you are drying. So if the spindle is 100 grams then a scale with at least 100 gram capacity and a sensitivity of 1 gram is what you need.

The reference test for moisture content is to stick a test piece of wood in an oven at 200 degrees and dry to constant weight. I have never had a 4/4 test piece take longer than 1 hour to get to zero moisture content, starting air dried.

With good air circulation commercial dry kilns dry poplar in 4-5 days from log to KD lumber.

Re: wood drying

#7

Re: wood drying

Mike Jurnigan in Suffolk, VA

Jack,

I learned seveal low tech ways for checking dryness of Windsor chair parts. For spindles; If you take 2 freshly shave spindles and hit them together you will hear a dull sound or a thud. If you hit two dried spindles together it will sound like hitting two drum sticks together, a nice sharp sound. Since I air dry my spindles how long it takes is based on the season. In the winter in a dry heated shop in about 2 to 4 days they are dry enough to use, in the summer, here in humid tidewater, it may take a week to week and a half.

For chair legs and stretchers I heat my tenons in hot sand on a hot plate, Heat the sand to about 140 degrees. I leave them in the sand until the tenons go oval shaped and start to turn gray from the heating. By the way I turn all tenons approximately 1/16" oversize and then file them round till I get a light squeaky fit when I press them together. Heating them in the sand should only take about an hour.

Bows take about the same time as the spindles to air dry or even a little longer. Again the tip for checking for dryness is to rap it against a piece of dry hardwood like a spindle and when you get the sharp sound it is dry enough to use. If I want to "cheat" the drying process I have found that the sack back arm and back bow fit in the oven perfectly. 24 hours in the oven on the lowest setting and it is "done." When you do this method you will know it is dry enough because the string or wire that you put across the bow ends will have slack in it. In other words you will have spring in instead of spring back. Dunbar places the bows for his classes in his furnace room at his shop. A few days in there and they are dry. All of them come out with the string slack.

Windsor chairmaking is not really high tech. I am pretty sure that they were not weighing their parts in the 1700's. In other words KISS, no offense intended.

Mike in Suffolk, VA.

Re: wood drying

#8

Jack Guzman from Maine

Re: Buchannan video?

Jack Guzman from Maine

Thanks Bill,

For the record,Curtis,in his video sticks the ends of his legs in holes in his kiln to dry the tenons. Michael Dunbar suggests hot sand in his book on Windsor chair making. I'm going shopping tomorrow with the wife for a good digital scale.---Jack

Re: wood drying

#9

Jack Guzman from Maine

Re: wood drying

Jack Guzman from Maine

Thanks Mike. I generally fret over the details until I get the hang of something,but I'm sure that once I figure out how to dry these tenons properly I'll relax a bit.---Jack

Re: wood drying

#10

Not trying to get Zen on you

Bob Hackett

But it`s a matter of experience really.

You can start out with digital scales and moisture meters but once you get rolling all those things will be gathering dust and you`ll wonder why you felt you absolutely had to have them back then.

Mike has given you some excellent tips more closely related to what you`re doing than my harvesting and drying techniques which are more geared toward bowl and spindle turning.

The one really good tip I would like to pass along is to take the batteries out of that expensive pin type moisture meter you had to have before you put it in the case and place it on the shelf. It`ll save you a lot of disappointment years later when you want to pass it on to someone who can really use it only to find the battery has blown up and your several hundred dollar meter is now toast because of a cheap 9 volt battery. Hate it when that happens. >(

Re: wood drying

#11

Re: Buchannan video?

Bill Tindall

when he demoed at our club meeting he used sand, but that was some years ago. If he has a kiln it is a more recent addition.

Re: wood drying

#12

Jack Guzman from Maine

Re: Not trying to get Zen on you

Jack Guzman from Maine

That is good advice Bob but I have never had a moisture meter.I couldn't justify the expense. I don't plan on spending more than $20 on a scale.

As far as not needing those things,I'm sure I'll find that it's true but I still need training wheels til I get comfortable with it. I dried parts in the kiln before and trusted that they were dry enough but I'm still not sure so I'm going to run some tests.Besides,I love experiments.It's all fun.---Jack

Re: wood drying

#13

Fun?

Bob Hackett

Why didn`t you say so. By all means, continue.

Besides, the wife will appreciate having an extra scale in the kitchen. ;)

Re: wood drying

#14

Things to do with a scale

Bill Tindall

Measure moisture content of lumber

Weighing stuff to calculate postal rates.

portioning food for freezing, eg. lamb pieces

cooking- weighing is vastly more accurate than volume measuring. I now weigh everything liquid or solid. About to make Pizza dough for tomorrow and everything from yeast to water will be weighed.

I prefer a scale that keeps its tare setting if the object is removed from the pan. to test add something to pan, tare, remove and set back. should read zero, many don't.

Re: wood drying

#15

Does your pizza dough turn out like

Bruce, a MN Galoot

your French bread? If so, I need a scale.

Re: wood drying

#16

you be the judge

Bill Tindall


Taught by Mario, of Mario Pizza, Oriskany Falls, NY

Re: wood drying

#17

Re: you be the judge

david weaver

Bill - how much flour is in that dough?

My bread books all recommend weighing flour, too, though I generally will make a pot bread, which doesn't require it - it just requires wet dough.

Pizza, I usually add the water (in a food processor) and then add flour until I get the consistency I want...but that wouldn't be any good in a restaurant to do it one at a time like that. I'd weigh it if I had a scale that had a tare function like you describe.

Re: wood drying

#18

Pizza recipe (how did we get from chairs to pizza?

Bill Tindall

Understand that where I live there is no quality New York Pizza. Most of the cells in my body were built with NY Pizza and I need it to keep them going strong, at least once a week.

For a medium sized pizza, add to a mixing bowl:

319 grams high protein bread flour, 3/4 TBS sugar, 1 tsp salt, 3/4 tsp instant bakers yeast, 1 to 2 TBS olive oil (I use 1 for a more chewy crust), 200 g water

Note- different bread flours stretch into the pie more or less easily. I use a readily available commercial flour- General Mills All Trumps.

Mix to bring together the ingredients. When the water is incorporated stop mixing and let rest 10 min to hydrate the flour. Continue mixing until dough becomes silky, about 5 min or less. Dump out on counter and "stretch and fold" for another minute or two. Return to a lightly oiled bowl, cover with plastic wrap and into the refrigerator till the next day to develop flavor(can leave it there 2-3 days if necessary, just keep the ball from drying out) The dough will be sticky and it needs to be to get good bubbles in the crust.

About three hours from cooking time remove from frig. and let dough warm up to room temperature. When ready dump out onto a heavily floured surface and dust surface with flour if it is too sticky. Push into a disk then stretch into the "pie" by what ever means you prefer. I like to toss it as it annoys my wife who thinks I will drop it.

Add topping, and into a 550 F oven on a pizza rock (or I use cheap unglazed red quarry tile squares) for 7 minutes.

Re: wood drying

#19

Re: Pizza recipe (how did we get from chairs to pi

TomD

Awesome recipe. We will have to try that. We have pizza once a week, but one has to make it oneself, pretty much a toxic food from the restaurants.

Re: wood drying

#20

Re: Pizza recipe (how did we get from chairs to pi

Kees

I like my pizzas thinner. More like the Italian ones. I use 360 gram flour on 200 ml water. The rest is about the same. This is enough for 2 to 3 pizzas.

Re: wood drying

#21

more details

Bill Tindall

If someone is actually going to follow these directions let me add some details. The rock or tile cooks the crust and the air carmalizes the cheese. There is a temperature gradient in a typical oven. Adjust the height of the rack so that the cheese is just right just as the crust gets medium brown.

Mario showed me a critical element in shaping. The dough should be a bit sticky. At the restaurant Mario dumps the dough into a tub or flour and thereby flours its surface to make it easy to handle. I dump it on a counter top covered with a thick layer of flour and dust some to the top of the dough ball.

When you start stretching the dough out into a disk it needs to be done one time or it will set up and require a 10 min rest to proceed. I push out a disk with the dough on the flour and in the process make a rim of thicker crust. Once the basic shape is established then I pick it up on both hands with hands made into a fist and with my clenched fists pull the disk into a larger disk. then toss it to impress the bystanders (or not) and transfer to peel. It helps to watch someone at Pizza shop do the stretching.

The rest in the frig is essential for flavor. During this time bacteria munch away on the sugars released from the wheat and the yeast is suppressed from munching. After the bacteria have their turn then the dough is brought to room temperature where the yeast can burp their bubbles that make the crust pretty.

Re: wood drying

#22

You have become disagreeable!

Bill Tindall

I suspect politics is less fractious than how people like their pizza crust. Indeed the true Italian pizza is a dainty single serving affair, which is what you describe. (actually I like this style too) And then there is the Chicago abomination made with corn meal! And the things midwesterners put on it-pineapple and ham-gag.

When pizza traveled across the ocean to NY three things changed about it. First, the wheat was different (we can't easily get the wheat you can which makes French Bread baking more complicated), and the NY ovens were coal fired and blazing hot. And, the pizza became something that served the family, not single serving. All this combined to make the NY pizza bigger, thicker and more loaded with stuff because our robust wheat will hold up more stuff.

Well the oven just beeped which means it is at 550 and its show time.

Re: wood drying

#23

Pizza Shaping details

Bill Tindall


dough ball dumped onto flour



pushed into a disk with rim raised



Stretched to size. First layer of stuff added. While I have made peels for others I never made one for myself. I just miltitask a cookie sheet. sheet of baking parchment under the pizza will make it slide off easily. I didn't use the parchment this time and had a time releasing the raw pizza to the oven tiles.


final product

Re: wood drying

#24

Re: You have become disagreeable!

Kees

Nothing like a bit of disagreement to stir discussion!

I also like simple toppings. Not too much cheese, the fat in the cheese makes the dough too wet. Some fresh herbs on top when the Pizza comes from the oven. Allthough it's early morning now I could eat a slice.

Re: wood drying

#25

Dang it Bill...

John in NM

You had to show a picture of a cooked pizza... 6:30 am and I want pizza :D

Looks really tasty, I grew up eating thin crust pizza that mom made. Still don't like most of the commercial offerings due to all that bread.