New WoodChat!
Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Price drop on over 1300 Rockler items

Rip Saw Options? Both Japanese and Western

Posts

Re: Rip Saw Options? Both Japanese and Western

#26

Checking grain direction ---

Texchappy

Should be going down the length of the box so that expansion is up and down evenly around the box - correct?

Re: Rip Saw Options? Both Japanese and Western

#27

David Barnett

Re: Checking grain direction ---

David Barnett

The joints of box sides should join at the end grain.

So yes, the grain should generally run the longer dimension of a board or box side (running horizontally if the bottom of the box is resting on a floor or table), so that the end grain is at, well... the ends.

The joints between the boards, be they mitered, rabbeted or dovetailed, should join at the end grain, even if the box is taller than it is wide. There are exceptions, but for now and for most boxes you should go with the fibers running in the longer dimensions.

You may see pronounced stripe running in the contrary dimension on some boxes, picture frames and even furniture, but this is usually veneer over a substrate such as plywood or MDF which remain more favorable to such schemes.

Re: Rip Saw Options? Both Japanese and Western

#28

Re: Checking grain direction ---

Texchappy

Gracias. I was pretty sure that was correct but while pondering something I began to wonder.

Re: Rip Saw Options? Both Japanese and Western

#30

Re: Won a Rip D8

david weaver

Sounds like dead straight with all good teeth, it should be a good one.

Re: Rip Saw Options? Both Japanese and Western

#31

Death Knell of my Ripping Woes?

Texchappy

Well, the D8 5 1/2 rip is on the way. I decided to rip off a piece for my box from a long piece of stock poplar with the Stanley sharp tooth. I was able to follow the line easily even with the huge amount of set on the saw. Got 'bored' with the slow cutting from the beneficial rust and relatively high ppi so I went back to the little ryoba. Result: went off line into the keeper part of the piece almost instantly.

BTW: couldn't resist the title. A virtual dollar to anyone who uses knell in a post not associated with death ;) Insert tongue in cheek (not tenon) now.

Re: Rip Saw Options? Both Japanese and Western

#32

David Barnett

(Message Deleted by Poster)


Re: Rip Saw Options? Both Japanese and Western

#33

The Birth of the Tallow Question

Texchappy

Funny you mention tallow. That was on my list of newbie questions to spread out as to not overwhelm any forum ;)

I've seen tallow as well as other lubricants (?) mentioned tangentially in several places. I haven't used anything yet. I understand the rust inhibiting and the air to letting the saw saw easier.

So, should I be using something like this?

Re: Rip Saw Options? Both Japanese and Western

#34

Re: Won a Cross-cut D8 - Good'un?

Texchappy

So someone said I needed a matched set on another forum and put in a low bid on this one and got it.

Did I get a bargain or waste $30?

http://rover.ebay.com/rover/0/e11400.m1842.l3160/7?euid=ee140b8909b9458999a2a74bbc087d52&loc=http%3A%2F%2Fcgi.ebay.com%2Fws%2FeBayISAPI.dll%3FViewItem%26item%3D290724026976%26ssPageName%3DADME%3AL%3AOC%3AUS%3A3160

Re: Rip Saw Options? Both Japanese and Western

#35

Re: Won a Cross-cut D8 - Good'un?

david weaver

Crosscut saws in the 7/8 range are probably the most common saws out there. A bit coarse for cabinetmaking, but good to break down stuff (a 7 ppi rip saw might also be nice).

You did fine. As ripping by hand becomes a little more common, 5 1/2 point rip saws have gone up, they're a nice size for 4/4 work and work that's a little thicker or a little thinner. Not nearly as common to find in the wild as a 7/8 ppi crosscut saw that a carpenter might've used.

Re: Rip Saw Options? Both Japanese and Western

#36

The Right Tools do make a difference

Texchappy

Got both my D8's today. First impression, 26" is a lot longer than it sounds. However, when I gave them both a test drive they sawed like a dream (at least for my experience). And I stayed on the line --which I couldn't do with my little ryoba.

I will have to do a pair of saw benches later on as I see where they would have made posture and work holding a lot easier than the make shift combinations of random basement detritus would have been.

Re: Rip Saw Options? Both Japanese and Western

#37

Re: The Right Tools do make a difference

david weaver

I'm glad you're pleased with them and how they work. I promise that all of my recommendations to buy something like that (western carpenter's rip saw) come from experience of using handsaws to rough lumber, and not from an idealistic viewpoint where I do 90% of the work with tools and just use handsaws every once in a while. I think in use, you will be as pleased as I am, and once you learn to touch up the rip saw with a file, manage your work holding, and really make it "sever the straws", you'll be very pleased how quickly you can work with it.