New WoodChat!
Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Compare cordless drills on the numbers that matter

How much plywood do you use?

Posts

How much plywood do you use?

#1

How much plywood do you use?

Texchappy

Watched a PBS woodworking show that wasn't Roy Underhill. One thing I noticed is that in the book case they were making everything besides a few hardwood pieces was plywood. I'm not a big fan of plywood but I've never bought the 'good stuff'.

So as at least part time hand tool users, how much plywood do you use? What are your thoughts on it?

Tony

Re: How much plywood do you use?

#2

It has its place

Bill Tindall

Large non-heirloom cabinetry is a reasonable application. Any place where there is a lot of "acreage" is another application. There was a plant here that did architectural panels and they laid up some spectacular veneers, sometimes on lumber core. These sheets made nice ends for cabinetry. I never considered it strong enough for shelving unless the units were not very wide.

Re: How much plywood do you use?

#3

Jack Guzman from Maine

Re: How much plywood do you use?

Jack Guzman from Maine

I prefer plywood for drawer bottoms unless I have a specific reason not to. It just works best. Sometimes,depending on the application,I will use it for panels.---Jack

Re: How much plywood do you use?

#4

Re: How much plywood do you use?

steve mackay

I'm very lucky and have access to the Fort Bliss "Packing & Crateing" shop scrap dumpster (scrap being defined as a piece to small for a packing crate for an M1 Abrams :D ). The main scrap is plywood. Due to this I've not lacked for free fire wood in the last twelve years. Yes Sir, I LOVE plywood and use it all wither long !

Re: How much plywood do you use?

#5

Ellis Walentine

Plywood as a design material

Ellis Walentine

The reason to use any material is dictated by the design problem at hand. I use it for built-ins, bookcases and applications where its dimensional stability is necessary. Someone mentioned plywood drawer bottoms. It can also be useful for plywood door panels or anything else that would benefit from this stability. You can glue it into housings and make it act structurally like the web of an I-beam, which affords greater strength with less structure around it than solid wood.

Plywood is not a hand-tool friendly material though, so if you want to be electron and carbide free, it's not likely to be a good choice for most projects. It is a good substrate for veneers, which can then be incorporated into more hand-tool-friendly projects.

Ellis

Re: How much plywood do you use?

#6

Packing crates

Bill Houghton, Sebastopol, CA

"...scrap being defined as a piece to small for a packing crate for an M1 Abrams..."

What, you guys don't cram those into flat rate boxes?

Re: How much plywood do you use?

#7

At my day job . . .

Steve Elliott

I spent this morning cutting up 20 sheets of 3/4" plywood for a kitchen we're starting. It's good stuff for casework that needs to be cost effective, but isn't what I plan to use a lot of when I retire and start making "jewel box" pieces in some style I haven't worked out yet.

Ellis is right about plywood not being hand tool friendly.

Re: How much plywood do you use?

#8

Re: How much plywood do you use?

eliot d

I used some very nice furniture -grade plywood to make some speaker cabinets for a friend, who insisted on mitered edges all around. I'll never do that again. Nearly impossible to get every edge exactly right -- even with splines. And then, because it's plywood, it's too hard to repair without going through the thin veneer. Would have been much easier to veneer MDF .

Re: How much plywood do you use?

#9

Re: How much plywood do you use?

Guillaume Dery

I mainly use it for built-ins and kitchen and bath cabinets, or anything painted which I just want to get out the door and don't really care about..

I am also a fan of the baltic birch plywood (or appleply) for workshop jigs and fixtures due to it's stability and consistency (it comes pretty darn flat and stays that way).

I second what was said about drawer bottoms and substrate (although as a substrate, be careful of the quality. bb or appleply have more layers and are void free. voids within can telegraph when you use them as a substrate).

Also second what was said about it not being hand tool friendly. Due to the amount of glue, you better get very good at sharpening your saws and chisels. Also as mentioned, the veneer on today's ply is VERY thin so you need to be mindful of that.

Re: How much plywood do you use?

#10

Re: How much plywood do you use?

TomD

Plywood tends to be used expediently in furniture, with the exception being stuff like the contract furniture business. I'm typing in front of a Step Tansu I built in Plywood. Part of the reasoning there, and it has proved correct, is that TV units do not remain in style long enough to warrant good materials. I never finished it either, I finished all the plywood stuff, but did not add the sliding doors because I couldn't bring myself to throw away good solid wood doors on this project.

Plywood is easily worked with hand tools. I have often dovetailed it, either for aesthetic reasons, or for practical projects where dovetails are a really cheap way to hold large panels together. I like to use planes when fairing curves on plywood, because you can feel bumps in the rate of change, and the plane will quickly straighten them out. I also cut scarph joints with planes. Etc...

Plywood that gets dissed is often the 0/90 stuff. The 0/0 stuff is very high quality you find it in high load bearing projects like seating. Quality isn't so much the issue really, it s more a mater of personality. 0/0 is more like solid wood.

Technically it is an awesome material. I was looking in a yachting magazine, current issue of Sail. There is a small trimaran reviewed in there, nominally 23 feet, but actually a little shorter. As such it is shorter an narrower than mine, and only a bit lighter. 38 thousand dollars, with about 6 K in better rig. I think with equal sails, my boat would beat it, and it cost 3500 in materials. Pretty much all vac bagged doorskins. Wood remains a fabulous structural material. Most of the panel material in the video is 1/4" thick, or 3/16". Imagine, the sofa is made of 1/4"plywood.

Re: How much plywood do you use?

#11

Re: How much plywood do you use?

TomD

http://www.youtube.com/watch?v=BnLmKXY-FCg&feature=results_video&playnext=1&list=PLF8B77C83E53DC8FA

Re: How much plywood do you use?

#12

Depends on what I'm making...

Bruce, a MN Galoot

Most of my case goods - cabinets, dressers, etc., have a fair amount of plywood in them. Bookcases are a mixed bag, about half solid wood and half ply.

Chairs, tables, night stands, beds, etc., are almost always solid wood, with the exception of drawer bottoms.

Re: How much plywood do you use?

#13

Who sais you can't plane plywood?

Kees

The good quality plywood with nice faceveneers is good stuff and occasionally I use it. It's always a trouble to hide the edges though.

When building my kitchen I had a little problem with one of the cabinets fitting too tight. So I opted to take a plane and make it narrower. In the link is a translation of my webblog page about this.

http://translate.google.com/translate?client=tmpg&hl=en&u=http%3A%2F%2Fseekelot.blogspot.nl%2F2012%2F03%2Fapparatuur-aangesloten.html&langpair=nl|en

Re: How much plywood do you use?

#14

Re: At my day job . . .

Patrick Gibbons

The majority of my uses of plywood are door panels, drawer bottoms and similar things. I've never had any problem cutting up this size with a hand saw and haven't needed power tools except for the rare occasional large panel. It has its place and I have no problem using it where it works.

Re: How much plywood do you use?

#15

I don't use it for drawer bottoms.....

Bill Tindall

...in fine furniture. Kitchen cabinets, yes. Most shops accumulate bits and pieces that are too good to burn, yet they don't seem to find a place in what gets built. These are the ideal pieces for drawer bottoms. Drawer bottoms are typically of a size that lends them to be a good place for these otherwise difficult to use lumber pieces. I resaw this "junk", then glue up the pieces to drawer bottom sizes and thickness. The last thing I made had bottoms of white and yellow pine, poplar and basswood which shrank the "junk" pile. Walnut and cherry sap wood also find their way into drawer bottoms.

Due to a communication error the last log I had sawed for drawer sides came out 4/4 instead of 5/4. When resawed to appropriate drawer side size I was left with what appeared to be uselessly thin waste. It became 5/16" drawer bottoms.

The longer of this "junk" finds its way into cabinetry backs, unless as Ellis pointed out, the back is a structural component that must be glued in.

Re: How much plywood do you use?

#16

Re: It has its place

Thomas Skaggs, Foothills of Mount Level

I use furniture grade ply for large cabinet backs. All of my work is finished as well on the back as the front. Time saver and cost cutter, yes. But stability is what motivates me the most. BTW- I inform all my clients when I use it.

T.

Re: How much plywood do you use?

#17

Toxic Glue?

Texchappy

Read somewhere along the way (and I've read a lot in the last month) that the glue used in plywood can be toxic. Figured that was another big reason not to use it. Is that info correct?

Re: How much plywood do you use?

#18

Not necessarily

Bruce, a MN Galoot

There is a line of plywood produced by Columbia Forest Products called Purebond that contains no formaldehyde. It doesn't off-gas nasty stuff. I'm using it on a baby dresser/changing table currently in production for our first grand kid currently in production. :D

Re: How much plywood do you use?

#19

Re: Toxic Glue?

TomD

The wood in plywood is toxic. There is a certain amount of glue in plywood which is part of the reason I don't personally burn it. Solid core plywood has a lot less glue. I might burn a piece I would not be comfortable heating with it.

What you may be referring to is the large amounts of sometime urea formaldehyde bearing glue found in particle boards and MDF The products use far larger amounts of glue to bind together dusts or chips, and often seem more cheaply made. I built some temporary shelving for a rental I lived in, out of MDF. They smelled really strongly of mushrooms and the smell stayed with them. Later I found "green" glue MDF at the local HD. Unfortunately it turned out to be a single pallet's worth only, and that is the last I have seen of that.

Re: How much plywood do you use?

#20

I wouldn't worry about it...

John in NM

As I understand it, formaldehyde vapor is emitted during curing, emission from cured resin is minimal. Rayon is a urea-formaldehyde product, yet there are no pop culture worries about it - doesn't have "formaldehyde" in the name you see :D

Perhaps someone who understands the chemistry better than I will weigh in on the matter.

Only plywood I'd have some concerns about is the really cheap stuff from China that smells a bit off. After the record with their drywall a few years ago, I could believe just about anything comes out of it :D

Re: How much plywood do you use?

#21

Marine plywood;  Boulter Plywood! *LINK*

Wiley Horne--So. Calif.

Marine ply is not only dimensionally stable, it is real wood through and through.

I bought a UPS load (75 lb or less is limit) from Boulter Plywood (see link), for use in jig-making, and possibly as a stable substrate for veneering.

Wow. This is one of the two or three finest vendors I have ever come across. Ever. First off, I wanted the pieces sawn to size--they offer this service very reasonable. Their saw cuts were precision, dead square and plumb, and smooth (no saw swirls), and on the money; careful packing; no dinged corners; even the offcuts were packed and included (I got everything I paid for, except the kerf sawdust). Shortly after the shipment arrived, I got a phone call from Massachusetts asking if everything was OK and to order. This was the first time I had done business with them, and a small order too.

I was very impressed with marine plywood. It's not that chip-filled CDX down at HD (which has its own uses of course). This stuff is joinable, holds fasteners, etc.

And was even more impressed with Boulter Plywood. They're good at what they do, and I found them most reliable.

Wiley


Boulter Plywood

Re: How much plywood do you use?

#22

Apply come common sense

Bill Tindall

I find it amazing that amateur woodworkers who have minuscule exposure to glue, finish, etc. fret over toxicity in the face of the fact that persons working in the factories 8-10 hour a day making this stuff, or using it, suffer no ill effects. Where does this stuff come from!

Re: How much plywood do you use?

#23

Re: Apply come common sense

Texchappy

I just asked a question to check the veracity of what I saw on the internet. I'm sorry if it was an amazingly stupid question. I won't ask anymore.

Re: How much plywood do you use?

#24

Rayon is......

Bill Tindall

cellulose. Cellulose, for example from wood pulp, is dissolved and reconstituted as a fiber called rayon. It is a stinky process. There was a Rayon factory nearby.

Urea-formaldehyde is cheap polymer used as adhesive and for molded parts. It may emit trace amounts of formaldehyde that some consider an issue under any conditions.

Re: How much plywood do you use?

#25

There's plywood and then there's plywood

Steve Elliott

While I haven't dealt with the company Wiley mentions, I agree wholeheartedly about what a good material high quality plywood is. Some types have hardwood for all the layers, usually birch, making them stiffer and better able to hold screws. The more layers the plywood has the more likely it is that it will stay flat.

I save scraps for jig making (a craft in itself, as I see it) and prefer it as an underlayment for veneer.

I can understand and respect the reasons for not using plywood in period reproductions. At the same time plywood has a long history and has been used by some of the best-known designers of the last century. If I'm designing for durability and cost, it's often a good choice.