New WoodChat!
Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Combination Press Plough Plane

Quote of the day

Posts

Re: Quote of the day

#26

Jack Guzman from Maine

never mind insulation(getting off track

Jack Guzman from Maine

I can recall many mid winter days here in Maine when the temperature was between 20 and 30 degrees. Sun shining,sky dark blue and me dressed in winter duds. I felt warm outdoors playing(ice fishing,sledding,skiing or whatever).The sung reflecting off the white snow put out a kind of heat.On the other hand my last experience of San Fran was waiting for a bus on Market street in mid July and shivvering in my shorts and short sleeves. I love the snow.---Jack

Re: Quote of the day

#27

Re: Your terminology's fine

TomD

I love what these guys make:

http://www.hybridburners.com/

I spent a lot of time making them myself, and it was largely more expensive, and the results were worse. I probably would have done better since learning to machine and weld, the plumbing ones are pretty much a waste of time, partly because all those fittings now come from China, in my local stores, and they are appalling quality. The guy who did a lot of the work on these burners, Ron Reil, now runs Hybrids in his forge, or did, last time I looked.

Re: Quote of the day

#28

David Barnett

Still time to rethink my burner choice

David Barnett

I know there are a few glass batchers, such as Mike Firth, who've used Ron's designs and mods for crucible furnaces and glory holes, but Rex Price has taken those early off-the-shelf-plumbing burners to whole 'nother level. I should take a fresh look at his hybrids now that I'm much more knowledgeable about chamber dimensions, exhaust holes and crucible volumes in contrast to the very different requirements of forges, which have lots of open and unused space and don't trap heat like a furnace or kiln.

Although Rex makes his two largest burners for foundry apps, there's still a lot of differences in BTU vs. chamber sizes to reach and hold the temps necessary to melt quartz as opposed to metals. He states on his site that he's not the guy to ask about foundries, kilns, and so on, but his burners could sure do the job in the right design with higher heat refractory.

For a small glass furnace, much smaller-sized Riel-type burners are often used, but I'd like to avoid blowers so lean strongly to venturi designs, as do most ceramicists, as well. One or two of his 1/2" Shorty burners might do the trick for a small crucible for primitive soda-lime or potash-lime glassmaking.

I'd set aside using a Riel or aspirated hybrid, but now that you've brought them back to my attention, I'll have a another look. They're pretty nice burners, if a little more than I'd like to pay, but I sure don't feel like making even a Riel/EZ-burner and don't want to turn and tune a nozzle or fiddle with making a decent choke on the venturi. It's not the turning that's tough, of course, but getting the contours right. I'd seen the Shorty on Riel's site some time back but had forgotten all about it, so thanks for the link. I'd never been to Price's site, at least not since it's looked like it does now.

Re: Quote of the day

#29

Re: Still time to rethink my burner choice

TomD

I think the Rex is the one you probably need. I bought 4 of the three smallest ones. He really tried to talk me out of the shorty by saying it would not be any better than the Rex turned down, and that the REX would pobably be better. I still thought it would be cute, and 5 years ago when I bought them, @, they didn't seem expensive for what they were. The smallest was in the range of a Bernzomatic. The Rex was really only materials more expensive.

Quite a few people prefer the blower based burners, but I decided that for me the venturi was safer, and easier. I think they are also supposed to be more efficient, which has several effects, one is the cost of gas, and the other is the need for tanks large enough not to cool and freeze. Also the blower ones seemed moreso for larger forges than I was making.

What I found when I wanted to make them was that basically tuning aside, the main advantage of the more optimal designs is that the jets have a longer lead. The main way people are getting that is by using victor type torch tips. The sources for those up here is about the same cost as a REX burner, which led me to cynically consider that at least some of the people making these were "taking their work home with them". :)

Now that I have all kinds of lathes and stuff, I assume I could deep drill such a thing, though whether the walls would be smooth enough is hard to say.

Then that tip had to be silver soldered. Which meant expensive silver, flux, and preferably an AO torch, none of which I had at the time, but all of which I now stock.

In this internet age, it is pretty much true that anything one has concluded has been shown to be false by someone else, but at least those where the parameters of my decision at one time.

Re: Quote of the day

#30

David Barnett

It's becoming fun again

David Barnett

I like the idea of running the larger T-Rex on a lower setting, which in my case, would give me plenty of BTUs with more control range, so when I get to where I can add cullet from previous batches to the raw elements (which cuts my time, op temp and gas usage), I can back it off and save some gas, even if it is fairly cheap these days.

If I can port it into my furnace at an angle which allows it to circle the side walls and wrap around the crucible somewhat, it'd solve the need for two smaller burners on opposite corners of the furnace chamber, which would also save me from buying another regulator and gauge. The other solution, of course, is to port across to the opposite corner, splitting the flame with a refractory wedge, although this would mean designing a larger chamber or changing the crucible diameter and height.

As for tank freezup, I've never had any problems even when running my big burner at 300,000+ BTUs on a 20-pounder so I'm not too worried about that.

Sounds like a single 3/4" T-Rex might do the trick for me, and at only twenty-five dollars more than the Shorty, it's a great deal, especially if I ended up having to add a second Shorty, regulator, hoses and tanks. I'd more or less become impatient at getting this project going, so had stopped focusing on the burners and was looking for more heat-tolerant refractory and multiple tanks to get me closer. Thanks for the useful info. I needed to get my excitement back.