New WoodChat!
Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Identify and use hundreds of woods

Sharpening station progress.....

Posts

Sharpening station progress.....

#1

Sharpening station progress.....

roger lance

the following photos show some progress on making a sharpening station for water stone use....this is the area that the single laundry tub will go (to the left of the main plumbing stack) and the sharpening table to the right of the stack.....


and here we are at the dry fit of the sharpening station which will be 24"w, 36"h, & 43 1/2"l.....


thanks for looking.

Re: Sharpening station progress.....

#2

Re: Sharpening station progress.....

Pam Niedermayer

I guess I don't understand all the waterstone mess people talk about. My waterstone use is pretty neat. Now if you want to talk about mess, talk about my Makita horizontal grinder which sends out a constant stream of gunk that sprays the walls, me, and everything in its sight line, looks like a laser measuring device scanning 360°. It was partially tamed by building it a three-sided box.

I can perhaps provide one tip for using waterstones, picked up from Jay van Arsdale: he dips the blade instead of the stone in the water for transport to the stone, very cool. Also, many put a waterstone platform over the sink they use for soaking the stones, although many these days don't require a full soak.

All that said, your station looks like a great build, as usual for you.

Pam

Re: Sharpening station progress.....

#3

Re: Sharpening station progress.....

Derek Cohen (in Perth, Australia)

Hi Roger

The base looks clean and tight. Excellent joints. Coming along very nicely!

Oooh. I am so envious of the space you have. I edge sideways past stationary machines.

Regards from Perth

Derek

Re: Sharpening station progress.....

#4

Re: Sharpening station progress.....

Bill Tindall

I think it will hold up a 4000 pound granite plate without problem.

Re: Sharpening station progress.....

#5

Re: Sharpening station progress.....

roger lance

Thank you Pam for your kind words.

Re: Sharpening station progress.....

#6

Re: Sharpening station progress.....

roger lance

Derek....I edge sideways past a few stationary machines myself....too much pasta.... :D .....the shop is 13'x28'.....but I have spread out into other parts of the basement with this sharpening station and some wood storage as what I had dreamed for this house will not be happening....so I envy you as well my friend.

Re: Sharpening station progress.....

#7

Re: Sharpening station progress.....

roger lance

Well Bill that is a BIG piece of granite.....and if I can get a small piece from an installer for reasonable dollars, I'll go that way for the top but that looks unlikely....so the laminate will probably be the way I finish it....but hey, I know how to work with laminate....so thats good....I knew this project would get your attention given your recent talk over the sand paper cabinet....and in some ways I agree with you about building too nice a piece that stays in the shop as will this piece....but I have used shop furniture to practice on before making something for the house and that is the case here....next up a dining room table about 42"x72" with legs only connected by aprons....no other structure....so I'm playing with this to test the M/T joints without the lower stretchers on the sharpening station to see how they are going to handle the loads/stresses of a dining table....and I won't be obsessing about all the little details on the sharpening table....I promise....the materials going into it from this point will be mostly bb and even some doug fir....shop grade material.

Re: Sharpening station progress.....

#8

Re: Sharpening station progress.....

Bruce, a MN Galoot

If you're looking for something waterproof, how about corian? A big cabinet company here throws away scraps as big as you'll need.

Good start on the work station!

Re: Sharpening station progress.....

#9

free rock

Bill Tindall

I stopped by the rock fabricator yesterday to look for a top for a hall table I am contemplating. They had stacks of sink cut-outs they were throwing away. Figure 20 pounds per sq. ft. for the thick rock.

Cheap diamonds has made this business possible. They can cut rock nearly as fast as I rip 8/4 lumber!

Re: Sharpening station progress.....

#10

Re: free rock

roger lance

Bill....I didn't want to hijack the tread from Alan on Messages.....but I plan to make a laminated leg for the dining table about 2 3/4" x 2 3/4" and then make mortises perhaps closer to the edge than on the sharpening station and double tapper the inside faces of the legs....nothing too fancy....the legs will be 29" tall and the aprons will be 4" wide which will give 25" under the aprons for leg room (which is fairly standard) and a tenon that is 2 1/2" tall (beginning the mortise 1" from the top of the leg)....and the table top will be about 30" from the floor....also standard....corner bracing is a possibility but this leg should be fairly meaty at 2 3/4" square (could go to 3" square but don't want to get to clunky).

Re: Sharpening station progress.....

#11

Re: Sharpening station progress.....

roger lance

Bruce....good idea....I'll check into corian.

Re: Sharpening station progress.....

#12

about tables

Bill Tindall

That is a stout leg you have planned. I would devote some effort to avoiding making the leg from two pieces. It never looks right. Cheap as I am I bought leg material for the table below even though I had more than a thousand of feet of cherry in stock.

You should consider making it an extension table. All that work into a table might as well make it versatile. It is handy with just the two of us eating to squish the table together and make it cozy, or extend it for miles when we have company.

A cock bead around the bottom of the rail looks nice...I think. I corner brace long legs. Easy to do and it adds robustness.


Re: Sharpening station progress.....

#13

Re: about tables

roger lance

Bill....If you would, please take some photos of your corner bracing as adding strength to this joint makes complete sense....I like the cock bead detail....the bottom of the rails need some form of rounding for comfort on legs....I'll be contacting my main lumber guy to see if he has 12/4 rift sawn white oak (otherwise the lamination will have to do)....my dining room is 12' x 12', so the 6' table length works well giving the people sitting on the ends 3' each to back their chair etc.....so the room itself really doesn't require a table that extends (but I'll look at that again also).....thanks.

Re: Sharpening station progress.....

#14

Re: Sharpening station progress.....

TomD

Does it have a mudguard? My LV waterstone sharpener has one and it sits at an angle to the stone and stops the spray. Not a horizonal macine, but the principle is the same?

Re: Sharpening station progress.....

#15

A link to the LV sharpener? I can't find it.

Pam Niedermayer

But here's a photo of it. There's no mudguard, although it's blocked on the back, and I suspect it would be very difficult to install one. I could sort of wrap one around, but it would have to be below the top of the wheel so I could flatten backs and the like.


Pam

Re: Sharpening station progress.....

#16

lumber source and leg brace

Bill Tindall

You won't find 12/4 rift oak lumber, but, that is not the place to look. You want to look for "turning squares" and pick 4 where the grain is running diagonally across the square. Adams in Morristown, TN sells turning squares but I don't know if they sell oak. Lots of other places sell turning squares. A stair parts manufacturer might have the white oak squares for making newel posts. Red for sure. An expensive alternative is to buy some 12/4 oak and rip the legs from the edges. The middle can then be resawed for some narrow (3") quarter sawed lumber. If you must, book matching the glued up leg can be attractive, but add a different look to a table leg.

I have been taking pictures along the way when I build stuff. It comes in handy for time like this. The picture shows the leg brace for an extension table. It looks like I was carving out the picket screw holes in this picture. The leg was made from a 3" turning square.


The table will have a different look depending on whether the leg is off-set from the rail more or less or not at all. Personally, I don't like a flush leg.

Re: Sharpening station progress.....

#17

Shortcomings of Corian.

Bill Tindall

Corian needs to be supported for it will droop over time if it is not supported. One of the reasons Corian installations cost so much is that so much needs to be done under it to keep it flat. The self supporting nature of rock makes installation cheaper/easier and this technology as put a big dent in Corian sales.

Personally for the task at hand I would either paint some plywood or use laminate of some sort, unless I found a free piece of rock or Corian of the right size.

Re: Sharpening station progress.....

#18

Re: lumber source

TomD

Two other options are are to get a log and split them out or chainsaw or bandsaw them out. It will take 6 months to a year to dry the wood. I got a piece of maple that when quartered yielded 4 pieces about 4x4. It took a little over a year before I got them dry enough to make planes out of. That was maple. The dimensions you want would be less time. However, it is possible to make legs out of wet wood. So long as the aprons are dry, the legs will shrink around the tenons. I would try that before I used lamination, which I just would not do. Also there is semi wet, can you really not wait a few months? Some logs are quite dry to start with in the form they were found, and they dry quickly at first. You rough them oversize and let them dry a while, and you will be working green, but they will not be soaking, it really won't be a big problem.

http://www.pbs.org/woodwrightsshop/video/3100/3107.html

The other option is to get some wood in anything from a about 2 quarters up in thickness, and miter the edges so that you can glue it on two sides over a core piece. With clean joinery this will look like a solid pieces since the grain on the outside edges is complete. That would work with elegant tapered legs, but if there is a lot of beef on the sides, or it is turned, it won't work. Even multiply lamination of thinner stock will look better.

Re: Sharpening station progress.....

#19

PS, editorial

Bill Tindall

The editorial is for those that have yet to build a classic bench. Without a doubt the leg in the picture could be immobilized a few seconds quicker on a traditional bench with its assortment of vices, stops , etc. However, with an ample collection of modern clamps I have never had any problem immobilizing anything I needed to on my bench which is basically a huge flat work surface and a metal vice. The point is that a classic bench is a work style choice not something essential, or even a significant advantage, for furniture assembly. Disclaimer, I make effective use of a thickness planer, jointer and table saw so I am not relying on a bench for these operations.

Re: Sharpening station progress.....

#20

Traditional work

Warren in Lancaster, PA

In traditional work we use long tenons going into the legs. For legs that are 2 7/8 square the mortises would be about 2 1/2 inches deep and the tenons would be mitred at the ends to keep from overlapping. In fact the advantage of having heavy legs like this is so that we can make a more robust joint. This is the kind of joint that can easily last six or eight generations. This construction is much stronger than short tenons or dowels or even a whole box of screws. A corner brace does little for a first class joint.

I agree about using solid wood for the legs. Laminated legs inevitably open up and are unsightly and difficult to repair.