New WoodChat!
Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Personalized Wooden Watches, Engraved Free

Re-visiting the end cap bolts.

Posts

Re-visiting the end cap bolts.

#1

Re-visiting the end cap bolts.

Derek Cohen (in Perth, Australia)

Wood moves, expands and contracts as moisture levels change, whether it is a process of drying out or the humidity levels in the air. The need to ensure that future adjustment - when required - would be easy, has motivated me to redo the end cap bolts for a third time. There will be no fourth time.

I have incorporated features from a discussion on the Ubeaut forum, plus added a design feature of my own (although no doubt this is not new - is there anything "new"? ... probably just re-inventing the wheel).

The probability is that, over time, the bolt and nut will weld themselves together through rust. Tightening the connection will be difficult unless the nut can be immobilised. One way is to remove enough waste to slide in a wrench or spanner. Another is to immobilise the nut from the outset ...

The forum suggested using a square nut. However, while it has its advantages over the old nut, a square nut still requires a spanner to immobilise it. So I have made a elongated rectangular nut, where the shaft runs the length of the bolt hole (and so is restrained by the hole, per se).

Here are the three methods I had used. From the left ... First I tried coach bolts. These were removed as I did not trust their holding ability in end grain. In the middle is the recently removed nut-and-bolt connection. Finally, on the right, is the new system, a bolt and elongated rectangular nut.


The nut plate was made from 1/4" thick x 1" wide O1 steel. Mike Wenzloff gave me an 18" length a few years ago. Nice to add a connection to a friend.

The second feature was the tapered ends to the bolt. Having used them this way now I can confirm that this makes connecting nut and bolt a much easier job.


Here is the set up ...


And here are the end cap bolts installed ...


Tightening now can be done completely from the end cap alone.

Regards from Perth

Derek

Re: Re-visiting the end cap bolts.

#2

Re: Re-visiting the end cap bolts.

roger lance

Derek....I like this modification very much....there will be no need for a fourth, you are there....I don't know that I've seen this done this way before (thats one of the real positives about wood/metalworking being able/free to use your mind to solve problems)....one of the things I like about dowel (barrel) nuts is that you can also tighten them from the outside of the cap with one wrench....for what its worth, I vote for leaving the bolt heads uncovered....Now for the really exciting part, mount that beautiful vise hardware!!!.....I'm looking forward to seeing photos of that....and I think the smile on your face the first time you spin that wheel will be like this :D .

Re: Re-visiting the end cap bolts.

#3

An addition suggestion

Bill Tindall

Over time the atom thick coating of zinc that the Chinese put on bolts now days will corrode away and over time the threads will mingle. I suggest you put some anti seize compound on the threads. Any place supplying machine shops will sell it. It consists of metallic particles of copper, maybe molybdenum sulfide and other stuff and I am not sure how it all works. I find it keeps nuts from seizing even outdoors. Or at the very least add a dab of grease.

Re: Re-visiting the end cap bolts.

#4

Re: Ditto

Hank Knight

Derek,

Ditto everything Roger said. Your solution accomplishes the same thing barrel bolts accomplish, only the installation of your elongated nuts is much more forgiving than installing barrel bolts. Nice fix. I can't wait to see the top with the hardware in place.

Hank

Re: Re-visiting the end cap bolts.

#5

Re: An addition suggestion

Derek Cohen (in Perth, Australia)

Hi Bill

I was wondering how the zinc coating of the bolts would interact with the O1 plate.

My thoughts had run to spraying on 3-in-1 white lithium grease, which is an excellent, long-lasting lubricant and is good for protection against corrosion. Whether it will protect against chemical welding in this instance is a question mark.

Regards from Perth

Derek

Re: Re-visiting the end cap bolts.

#6

no mixed metal concern

Bill Tindall

The galvanized bolt will be happy snuggled against the carbon steel "nut". The piddly amount of zinc coating on a plated nut would be scrubbed off upon tightening anyway. The grease will be somewhat effective and likely effective enough to prevent the threads from corroding together over decades.

Re: Re-visiting the end cap bolts.

#7

Stainless nuts and bolts?


Re: Re-visiting the end cap bolts.

#8

Then you can polish them. :^)


Re: Re-visiting the end cap bolts.

#9

Re: Then you can polish them. :^)

Derek Cohen (in Perth, Australia)

Both LV and Benchcrafted make excellent connectors. I did consider them, briefly.

I decided when starting out on this bench, where possible, I would build what I could - not for cost reasons but just because I like to make/invent/fiddle. The Benchcrafted end vise is one exception and was purchased because making an equivalent was down right impossible, as was the wooden screw for the leg vise (although I did consider turning one).

I would love to use stainless steel for the bolts. These are not easily available in Perth, neither are connectors of the LV/BC type. I therefore use what I can from the local borg, and modify/beat it to fit.

Regards from Perth

Derek

Re: Re-visiting the end cap bolts.

#10

Go to the nearest boatyard

Bob Hackett

You`re on the coast right? I would think a trip to the nearest coastal (salt water) boatyard would give you a wide choice of hardware in either stainless steel or bronze. Look for one with a lot of tall masts nearby and I`ll bet they`d even polish them for you if you produce a credit card and are willing to take out a second mortgage on the homestead. :D

Re: Re-visiting the end cap bolts.

#11

not the boat yard

Bill Tindall

The patina steel bolt heads will look just right on this bench 100 years from now. The stainless steel won't. I would sand the zinc off any exposed steel parts so the bolts look like they belong to the bench as the bench acquires character.

Re: Re-visiting the end cap bolts.

#12

Looking pretty good, Derek.


Re: Re-visiting the end cap bolts.

#13

Patina? Go with bronze