New WoodChat!
Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Super Resolution Thermal Imaging Camera

Hand finishing drawer fronts

Posts

Hand finishing drawer fronts

#1

Hand finishing drawer fronts

roger lance

On a prior thread, we talked about the possibilities of finishing drawer fronts prior to assembly of the drawers including the sides/pins....being convinced that for me it is prudent to finish parts of projects prior to assembly, I had to give it a try....


This is a photo of the drawer with blue tape to protect the vital glue surface in dovetail....and a photo with the tape removed....a little touch up required....


and the drawers in the case with dovetails showing....


and the piece ready to go into service....


thanks for looking.

Re: Hand finishing drawer fronts

#2

NICE WORK


Re: Hand finishing drawer fronts

#3

Nice work

Bill Houghton, Sebastopol, CA

and man, that is some PURTY wood!

Re: Hand finishing drawer fronts

#4

There is a down side.....or alternative universe

Bill Tindall

First, the chest of drawers looks great. Just love the front.

I am unable to get the fit I want in a drawer by cutting parts and assembling the drawer. I plan on fitting the drawer after assembly and therefore make sure it is at least slightly too big. Then I plane the sides for a precise fit.

Also, I don't stain the inside drawer front or the pin ends. Just a personal preference. I do shellac the interior drawer parts. Shellac keeps the drawer insides looking fresh and shellaced outsides makes the drawers slide easily.

Re: Hand finishing drawer fronts

#5

Re: There is a down side.....or alternative univer

roger lance

Bill....I spent a good deal of effort with the drawer in the dry fit adjusting the fit....making sure all parts went together properly and there was appropriate room for side expansion etc....the drawer guides are set in the case at 90 degrees to the front drawer dividers, so I glue up outside the case at 90 degrees and will correct after if needed....so my method is not a time saver....the effort you expend after the glue up, I'm trying to do before.

I agree about the shellac on the drawer box....one coat....rubbed out with a nylon pad.

I then wax the drawer guides and bottom of drawer sides/slips.

Re: Hand finishing drawer fronts

#6

Re: Hand finishing drawer fronts

Guillaume Dery

REally pretty Roger. If you don't mind my asking, how did you finish the piece? I assume that there is some staining going on here prior to the top coat. Please share because that piece is looking very good!

Re: Hand finishing drawer fronts

#7

That's one fine piece of work.


Re: Hand finishing drawer fronts

#8

Finishing schedule for QSWO

roger lance

Guillaume....the following is a generalized summation of a hand finish for white oak....

Raise the grain with distilled water

Apply TransTint water based dye to establish underlying color (I use a brown dye).

Seal with wax free shellac.

Apply oil based glaze (I used a dark walnut stain).

Seal with wax free shellac and continue with finish coat of choice building as desired.

Apply wax if desired.

Re: Hand finishing drawer fronts

#9

Re: Hand finishing drawer fronts

Derek Cohen (in Perth, Australia)

Hi Roger

That is really terrific. As a friend of mine would say, "it looks like you bought it" (which is his way of saying it is well made).

The finish looks good. Personally, I do not pre-finish, but then what I do is not a recommendation for best practice. Like Bill, my drawers end up a tad oversize, so I leave them in a squaring jig while the glue dries, then plane to fit. I finish the outside face and sides, but never the insides (which just get a rub down with paste wax). I do not use shellac on the insides because I find it will raise the grain, and then I have to sand it back. Wax (or even left bare) is my preference. Writing this I realise that, were I to plan on a shellac finish internally, it would need to be completed before assembly (so as to do the sanding).

Regards from Perth

Derek

Re: Hand finishing drawer fronts

#10

Meet the piece that taught me to pre-finish...

roger lance

it's MY bed :( ....sitting in my basement waiting for me to take it on....lordy....if ever there was a piece that needed to be finished THEN glued....its this....water based dye loves to run....and although I'm able to command language that makes just about any combat veteran blush, that dye is gonna run on me....but I'm taking it on this winter and planning to use spray shellac when the weather turns....now that I've put it on the net, I can procrastinate on this no more....this is the foot board....the head board is under the wrap.


Re: Hand finishing drawer fronts

#11

No......

Bill Tindall

I glue the drawers in the case so that they fit what ever shape I have made.

Then I slather on a coat of 1.5# shellac. Certain foam brushes work great for this task (the changeble ones from Woodworkers Supply). Sand with 300-400 grit (whatever is on hand) stearated paper, and then another coat of shellac. I shellac the insides of the case too, same procedure. It is easy to knock the whiskers off the surface with the drawer assembled.......However........if you are getting grain raised something is amiss. Shellac raises sanding whiskers on a sanded surface but there is no roughening of a hand planed surface.

Wax on shellac is exceedingly slick.

Re: Hand finishing drawer fronts

#12

To the rescue.....

Bill Tindall

treat it with ammonia. That's handsome.

Re: Hand finishing drawer fronts

#13

Re: To the rescue.....

roger lance

Bill....I've thought about fuming....and have experimented some but never realized anything close to the color/tone of other pieces that will be in the bedroom with this bed....but I still have not ruled fuming out....it sure is an easy way to get into all those nocks and crannies....and fuming continues to be acceptable finishing practice by guys like Kevin Rodel....by the way, the steelhead are in the rivers around these parts.

Re: Hand finishing drawer fronts

#14

Very very nice Roger.


Re: Hand finishing drawer fronts

#15

Re: Finishing schedule for QSWO

Guillaume Dery

Thanks Roger.

Finishing is one of my blind spots which I really need to address. Of course, I can always improve on my handtool technique but I am finally at the point where the piece I build is the piece I meant to build (with some occasional detours to correct aw crap moments). Finishing however.... Specially with stains and dyes. I do an OK french polish and an oil and wax finish is basically foolproof but I have a LOT of room for improvement.

Obviously this is not your issue. That finish looks bloody fantastic!

Re: Hand finishing drawer fronts

#16

Re: Finishing schedule for QSWO

roger lance

Guillaume....you are too kind....however, like most woodworkers, finishing is not my strong suit....one of the reasons I decided to build in the A&C/Mission style was that I could apply a finish by simple hand techniques and not get into more specialized equipment like spraying with the potential of blowing the house up (just kidding....sort of)....I think a woodworker would do well to learn a couple of finishing schedules....get good at those techniques....and be thinking finishing on a project right from the beginning of the build just like you do the joinery....and I find that I really like finishing parts before the glue up (the disagreement on this reminds me of one guy saying "pins first"....and another guys saying "no, tails first")....look up Jeff Jewitt of TransTint, he offers some finishing schedules with dye etc....keep at it.

Re: Hand finishing drawer fronts

#17

Re: No......

Patrick Gibbons

I always polish, that is, use a rubber and apply by hand. There is much less sanding involved, if any. I shellacked a piece similar to the bed you're making. Polishing worked like a charm.

Re: Hand finishing drawer fronts

#18

Re: Hand finishing drawer fronts

wilbur

Terrific job. I always like looking at your projects, Roger.

Re: Hand finishing drawer fronts

#19

Thank you all for your nice comments....

roger lance

it's good to be part of the community here :) .