New WoodChat!
Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Want Better Milling & Firewood Knowledge?

Dealing with a bendy board

Posts

Re: Dealing with a bendy board

#26

Re: More Clarifications

Warren in Lancaster, PA

Bill, you list three reasons why a panel could cup. This is textbook material. It bears repeating because many woodworkers are foggy on these points.

However none of this explains what a "bendy board" is or why Wilbur was unable to get one side flat, even temporarily. Wilbur had a cupped board. He took full length shavings across the width, removing material from both high and low areas. A much more effective strategy is to plane only the edges if you are flattening the concave side, or only planing the center if you are flattening the convex side. Wilbur also apparently planed both sides without first getting one side flat, as Larry pointed out. Nicholson, in 1812, wrote that one should plane "all the protuberant parts or sudden risings" when trying a board. And to "first face the side of a board"

Re: Dealing with a bendy board

#27

Re: Dealing with a bendy board

Pam Niedermayer

I see, in that case 3/4" sounds real good to me, but at this point I'd probably use it as one of the internal dividers. I don't know what style you're shooting for. I'd probably forget the frame for the internal dividers, go straight with sliding dovetails top and bottom to hold them in place, then use frame/panel for the two ends, with a 1/2-3/8" panel. But then I'm a real wood and time miser, one who doesn't get any kicks making more frames than I have to. :)

Pam

Re: Dealing with a bendy board

#28

Re: Dealing with a bendy board

TomD

"First things first, to all of you brutal perfectionists. I love you all, and you make valid points, but the joinery we use was designed to enable us to work with a material that moves with the seasons... and to keep it from moving in undesirable ways."

That is true, but is not the case in point, this is about error in the parts as they come together, which may or not be a problem. That isn't a mater of theory, it comes down to cases, literally. To get the stuff you refer to to work you need to get the parts well made to start with. Building in stress is not a great start. To take as simple example, knowing one's wood, environment, and design, one might conclude that a gap in a cabinet door of 1/16" was a good deal. Would it then be sensible to conclude than in executing that par the tolerance is 1/16"? Obviously not.

"This isn't machining, here, it's woodworking."

Well acutaly it is machining, hand planes are machines, and the tolerances they are capable of is similar to my mills, lathes, and reciprocating shaper. More to the point the tolerances of good woodwork are the same as machine work. There are differences in the two disciplines, general sloppyness is not one of them.

"Some woods are more stable than others. Not everything can be quarter-sawn, pattern grade stock. Up here in Boston I have a beautiful 6-board cherry blanket chest. Every winter, the 18" wide, single-board lid cups, even with the applied battens, and the front opens up by 1/4". Every summer it flattens back out again. Wood moves. 1/32" of an inch over 20"? the wood might move more than that by tomorrow. So I wouldn't sweat it."

Not sure I agree with that. The fact is it probably would not move that much in an unheated enviro. The modern home is not really the standard for traditional woodworking. It blows up musical instruments and antiques. Are you really suggesting tha 1/4" is ok, and did the guy who made this work to that tolerance or is that just the abuse it is managing in it's new quarters? My dad owns a very nice Grand Piano, a Bechstein. Over the 35 years he has had it, he has pampered it with every system of humidification known to man, yet all the veneer on the case has either wrinkled up, or drapped, off. Let's just call it good...

"Wilbur, if you clamp the panel between some cauls to keep it reference-flat while you cut your joinery, and keep it that way during assembly, it should stabilize in situ, and be fine. I see no difference between this, and letting a perfectly flattened board react later, post-assembly. As long as it's trapped in a dado or a groove, it's not going anywhere."

Yeah if it starts out flat, and something goes wrong, you can throw it out on the grass during season, or maybe a damp towel in winter, and get it to come back. Assuming the fault is warping, and asuming that the humidity the board was seasoned to is typical of it's final resting place. Assembling with strees isn't always the same as the way something goes later one. And it is also the case that once something is in a piece, as with this dust panel, it will tend not to move around as much because it's end grain is encased in other boards, and those boards also cloak it.

"Or, you can follow the advice of Tage Frid, who came from a traditional European system of apprenticeship: Moisten the concave side, and hit it with a hot iron. The steam should expand that side, and flatten out the board for you. Obviously, you shouldn't do this with a garden hose, do it in increments."

Apparently his advice wasn't to just hammer it home...

I'm sure one could get away doing stuff as you suggest, I just don't see the harm in high standards, often the last few strokes across the stone are the ones that bring up the edge. Why toss away all the work that went into getting there when one could have a much sharper and longer lasting edge by going only slightly further.

Re: Dealing with a bendy board

#29

Reality in dealing with cupped panels

Bill Tindall

Two questions were asked, the first whether the panel could be used as is and a followup on what might have caused the unexpected cupping. I have been astonished by the responses. The answer to the first question was so obvious that I didn't justify my answer thoroughly.

There are a variety of reasons one may be faced with a cupped panel part. If the amount of force to make and hold it flat will not stress the joinery holding it in place there is no practical reason to fret its lack of unrestrained flatness. The finger flattening test is a good one.

While a cupped panel can be flattened by proper hand planing technique, as Warren pointed out, the task of flattening is not at all convenient for those that machine plane panels. My huge planer will mash the cup from any panel 3/4" thick. Hence, it is a common occurrence to have to deal with panels cupped a bit. I put the panel on the table saw and if I can make it flat with hand pressure I am assured that it will never stress any joinery it becomes part of. Anyone that argues this is poor workmanship, or however lacking, is simply unrealistic, doesn't have enough real problems to worry about, or does only theoretical woodworking.

One has to use good sense in these matters. If an 8/4 panel was cupped 1/4" I would not attempt to make and hold it flat with joinery. This consideration is why I don't try to face glue 8/4 lumber. It is just too strong. However, because I have been lackadaisical about storing them I have 1/4" pine drawer bottom panels that have cupped an inch. So what? They slip into their drawers effortlessly.

Re: Dealing with a bendy board

#30

The myth that old homes were better on furniture

Bill Tindall

The outside humidity in Minneapolis when I lived there was essentially zero in the winter and near 100% for the few days of summer that some years occurred in July. Wood responds predictably to changes in humidity with corresponding changes in moisture content and in turn dimension. How this uncontrolled environment can be thought to be superior to that in a modern home escapes me. I don't notice that museums emulate the fireplace heated, more and less, rooms of 1720. Rather they control temperature and humidity similar to a modern climate controlled home.

I suspect the true problem is that at some time or another the furniture in question was in fact stored at ambient outside conditions and the wood soaked up moisture and expanded. It was when these swollen joints ventured indoors and dried out to modest levels that joints failed. One doesn't see well made modern furniture made with KD woods failing in the heated rooms of a modern home.

Re: Dealing with a bendy board

#31

Re: The myth that old homes were better on furnitu

TomD

"The outside humidity in Minneapolis when I lived there was essentially zero in the winter and near 100% for the few days of summer that some years occurred in July. Wood responds predictably to changes in humidity with corresponding changes in moisture content and in turn dimension. How this uncontrolled environment can be thought to be superior to that in a modern home escapes me."

Part of the reason could be that they didn't store their furniture in the out of doors, and that the interiors retained a more moderate climate. My unheated garage maintains a surprisingly stable climate through the seasons, when heat and humidity are taken into consideration. The other secret could be that the world's historic furniture heritage was not dependent on Minneapolis.

"I don't notice that museums emulate the fireplace heated, more and less, rooms of 1720. Rather they control temperature and humidity similar to a modern climate controlled home."

No they control conditions in a way that is desgined to ensure they are always needed, and that does not copy conditions in modern homes. My wife was in the museum conservation business, for a while.

1720 was hardly the cross-over, many places when I was a kid did not even have central heating.

"I suspect the true problem is that at some time or another the furniture in question was in fact stored at ambient outside conditions and the wood soaked up moisture and expanded. It was when these swollen joints ventured indoors and dried out to modest levels that joints failed. One doesn't see well made modern furniture made with KD woods failing in the heated rooms of a modern home."

Yes one does, and most people who work in the biz have stories, about sending stuff across the country. If you make it in your own home and keep it there, there is a lot less trouble. I just retold the story of the local cabinet shop and their exploding tables a few weeks back. Most modern funiture is not made of solid wood, and Kiln dried wood is not more stable. I don't know of much modern furniture that does not break in 20 years, or less, most of it lives at the dump.

Re: Dealing with a bendy board

#32

Re: The myth that old homes were better on furnitu

Pam Niedermayer

Just as metal tools often benefit from being stored in wooden boxes, maybe furniture does, too; so if the house is old enough to be a wooden box....

Pam

Re: Dealing with a bendy board

#33

Re: The myth that old homes were better on furnitu

AlanWS

It's heating your house that makes the humidity be near zero in the winter. There is very little water in the air outside, but also very little capacity for water at that temperature, so the humidity as a percentage of that capacity is not so low. A house heated by fireplaces would be pretty dry near the fire, but might not dry out furniture in the colder parts of the room as much as would a well heated but unhumidified house in Minnesota in the winter.

While the extremely high humidity of a Minnesota summer won't be seen in a continuously air conditioned space, the extraordinary dryness of the winter is caused by central heating. I read somewhere* that in Britain, a higher fraction of people lived in homes with central heating under Roman rule than at any time until about 1950, so maybe central heating is a more modern phenomenon than we might think.

Museums air condition in summer and humidify in the winter, in order to keep humidity as constant as possible.

* somewhere: http://books.google.com/books?id=ULxZAAAAMAAJ&q=central+heating#search_anchor

Re: Dealing with a bendy board

#34

Just a note about seasons and geography

Bill Houghton, Sebastopol, CA

Here on California's North Coast, the typical winter* means lots of rainy days. Humidity is higher, at least in our house, in the winter; relatively low in summer. The doors that swell do it in the winter, not in the summer. Even on the days that start out below freezing, there's typically a lot of moisture in the air.

I've lived in the Midwest, where you can slice and chew the air in the summer; so I'm aware that the statements about humidity being high in the summer, low in the winter are true for much of the country.

*This year's not typical - we're close to typical rainfall for the season, but it's fallen in two storm series, in October and mid-January, with weeks, nay months, of no rain. Everyone's been fretting about another drought year, with the reservoirs, and Sierra snowpack, on which we depend for water draining down.

Re: Dealing with a bendy board

#35

Re: The myth that old homes were better on furnitu

TomD

"Just as metal tools often benefit from being stored in wooden boxes, maybe furniture does, too; so if the house is old enough to be a wooden box....

Pam"

There certainly are modern day natural builders who are strong believers in the breathability and stability of climate in old homes.

Re: Dealing with a bendy board

#36

Re: The myth that old homes were better on furnitu

Pam Niedermayer

Yeah, newer houses often have so little ventilation and so much outgassing from plastic parts that they have to run heating and a/c all the time just so the occupants can breathe. They may be efficient heat holders, but what a price.

Pam