New WoodChat!
Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Abingdon, VA – Tree Cutting & Portable Sawmill

Shaker Table Completed

Posts

Shaker Table Completed

#1

Shaker Table Completed

Todd Nebel

It's done! Thanks for the help along the way. Happy to answer any questions if there are any.


img

Re: Shaker Table Completed

#2

Second Photo

Todd Nebel

I went with three evenly sized boards for the top.


img

Re: Shaker Table Completed

#3

Third Photo

Todd Nebel

Close up on the leg beads and the drawer front. I turned the knobs.


img

Re: Shaker Table Completed

#5

Re: Shaker Table Completed

Derek Cohen (in Perth, Australia)

That is beautiful Todd. Not just the choice of wood, but the execution.

Want to trade it for one in Jarrah? .... I thought not! :)

Regards from Perth

Derek

Re: Shaker Table Completed

#6

Re: Shaker Table Completed

roger lance

Todd....I like it very much....you did very well....and I like that top....the symmetry of the three boards works so very well for me....there is no distraction of the eye by looking at disproportion in the boards....the eye takes in the reassurance of the balance/symmetry and goes to admiring that stunning figure....congratulations.

Re: Shaker Table Completed

#7

VERY nice

Bill Houghton, Sebastopol, CA

The Shakers had it right: 'tis a gift to be simple.

Re: Shaker Table Completed

#8

Re: Shaker Table Completed

GolfSteve in Calgary

It's a spectacular beauty. Nice job on the top; matching figured maple like that is not easy. Great photography also.

I have to admit I don't like the visible dovetail on the rail under the drawer.

Re: Shaker Table Completed

#9

Re: Shaker Table Completed

bob murphy

Beautifully done!

Re: Shaker Table Completed

#11

Re: Shaker Table Completed

Bill Houghton, Sebastopol, CA

I agree. Given the difficulty of "matching" grain on tiger maple, where the cross-grain pattern is the dominant pattern, three boards the same size makes the most sense.

Re: Shaker Table Completed

#12

Re: Sweet!  What's next?

Todd Nebel

Hi Bill,

With the leftover wood, pre-mixed dye, and shellac; I think I will make a small cupboard to hang on the tall wall near this piece. I just need to find a design I want to build.

Todd

Re: Shaker Table Completed

#13

Thanks for all the kind words.


Re: Shaker Table Completed

#14

Re: Third Photo

Steve Kirincich

Beautiful! Can you comment on the finishing sequence? Thanks.

Steve

Re: Shaker Table Completed

#15

Re: Shaker Table Completed

Gary

Nice work!

Re: Shaker Table Completed

#16

Re: Third Photo

Todd Nebel

Hi Steve,

The round part of the legs were sanded on the lathe to 600 grit. All other flat surfaces were planned only prior to finish.

It went something like this...

Wet the surface to raise the grain and used an old 320 grit piece of sand paper to knock off the fuzz.

Applied a 1/8th strength coat of water based dye (Honey Amber). Used a cotton cloth and let dry over night.

Applied a full strength coat of dye. Used a grey scothbrite pad and "kind of sanded" as I applied. Let dry over night.

Applied a Linseed Oil bath. Let dry a week.

Applied several coats of amber shellac (1 lb cut) and then many coats of clear shellac (1 lb cut). On the weekend I could apply 3 coats a day, during the week only a single coat after work. I lost track of how many coats in total. At first I used a grey scotchbrite pad to sand between coats of shellac, but as the shellac built up I used 500 grit sandpaper.

I ordered some Liberon Bison wax (Yew color) online. When that arrives I will add a couple coats of wax.

Hope that makes sense and helps.

Todd