New WoodChat!
Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Precision you can feel — woodworking perfected with Lee Valley

Hot hide glue mishap

Posts

Hot hide glue mishap

#1

Hot hide glue mishap

Robin Corell in Atascadero CA

Yesterday I had a rather messy catastrophic failure of my glue pot. The set up I have been using for the last five or six years is a mini crock pot. The crock pot I have was free with the purchase of a regular size crock pot and it was recommended for warming cheese or been dip. One cup of dry glue will fill it to the brim when mixed with water; I usually mix 3/4 cup dry 192g glue.

The mini crock pot gets way too hot so I made up a 4 gang box with a receptacle on one side and a dimmer switch on the other, combined with a meat thermometer it is a set up that has served me well. The dimmer switches last for a bit over a year before they need to be replaced, which is more of an inconvenience than a financial consideration. It was always in the back of my mind to pick up a variac and last summer a good friend gave me one, so for the past couple of months I have been plugging my mini crock pot into a variac rather than my home made set up with a light dimmer switch. The difference between the two is that with the dimmer switch the glue would come up to temp and then over a few hours it would slowly continue to rise and with the variac it will hold at whatever temp I set it to with no creep.

When I know I will not be using glue for a week or two I put the whole crock pot in the freezer and I have never had a problem until yesterday when the bottom of the crock pot blew out. In the past when I pull the glue out of the freezer I usually forget that it has been frozen and I need it hot ASAP so I crank the dimmer switch till it is up to temp and then back it off to its holding temp setting, but I am not sure if I have always heated my frozen crock pot by cranking the dimmer. Yesterday I pulled the crock pot out of the freezer and plugged it into the variac and set it at the holding temp setting because I had a doctor’s appointment and would not need the glue till after noon, I had meant to turn the pot of while I was gone but drove off with it plugged in, which should not have been a problem.

During the time I was home and monitoring the glue pot it was not defrosting like normal. Usually the outside edges would melt a bit and slowly the lump in the middle would disappear. I have only used the variac with a frozen glue pot one other time and that time I was in a rush to heat up the glue so I cranked it to high and then backed it down to a holding temp. I am now wondering if the variac is so controlled that it melted a small amount in the very bottom but none around the edges and as the melted glue expanded the frozen glue at the top caused a buildup in pressure that blew the bottom off the pot.

Of course it could be that the repeated freeze thaw cycles of the crock pot caused small stress cracks and yesterday it just reached a critical mass so to speak.

A third possibility is that a couple years ago I cooked the pot dry and the drying glue pulled a couple of chips off the sides of the crock pot and this caused damage that eventually caused a failure. I suppose you could even argue that it was a combination of all three scenarios.

I do have a back up mini crock pot so I will be able to melt up some glue for this afternoon. I really do not want to repeat the mess I created yesterday, luckily I discovered it in time otherwise my Gerstner box would be firmly attached to my bench. I am sure I could limit my problem by not freezing the mini crock pot but it has saved me a lot of wasted glue over the years and has up till yesterday worked very well for me. I would like to hear other opinions on what might have happened and how best to avoid a repeat.

Sorry for the long post without pics but when I saw the mess I sort of panicked and by the time I thought about taking a pic I was elbow deep in gelled glue mess.

Robin

Re: Hot hide glue mishap

#2

Re: Hot hide glue mishap

Dean J in MN

I mix up my glue is small glass jars, then use the glue pot (or crock pot in your case) as a double boiler -- just put water in the glue pot and put the glass jar in that. Then when you are done for the day, cap the glass jar and toss it in the fridge. I don't freeze mine, it keeps for quite some time in a fridge. I go through it fast enough that I've not had it turn ugly on me. :)

Re: Hot hide glue mishap

#3

That's what I do

Neal in San Jose

The difference is that I paid the staggering sum of $9.99 for my mini-pot at Target and it has a built-in temp control. The down side is that low is a just little too low and med is a little too warm. I try to remember to leave it on low and just bump it up on med when it is too cool. It warms up to usable temperature on med pretty quickly and it stays that way for a while, so it isn't a deal-breaker. High is way too high.

Luckily for me a couple of ladies at work just had babys, so getting baby food bottles hasn't been an issue.

Re: Hot hide glue mishap

#4

Re: Hot hide glue mishap

TomD

Depends on the scale you use it. I use open pots so I can get a brush in there and use it heavy or really light. For folks who like hot hide glue but wish they lived in Hell so came in squeeze bottles, this is the hot set-up:

http://www.lenaweelutherie.info/page6/page17/page17.html

I have to confess it looks about right. I just read the pics. Marbles, check; bolt, check; squeeze bottles, check; etc... If it doesn't make sense search for similar set-ups.

Re: Hot hide glue mishap

#5

Robin....

Thomas Skaggs, Foothills of Mount Level

...Please never invite me over for fondue or hot cheese dip. Thanks

Hey, by the way, the new workshop is nearly completed. I won't be sitting on the sidelines much longer!

T.

Re: Hot hide glue mishap

#6

Re: Hot hide glue mishap

Kelly Anderson

I use the same "hot pot" as in the link only I use small Mason jars for the glue. It keeps the temp. really well. I drilled a large hole in the lid and cover it with the jar lid betwen glueing joints to help keep the heat/humidity in. A squeeze bottle seems like a good idea and I could just stick it in the hole in the lid.

Re: Hot hide glue mishap

#7

Re: Robin....

Robin Corell In Atascadero CA

But the glue is edible........tastes like chicken.

Re: Hot hide glue mishap

#8

Re: Hot hide glue mishap

Robin Corell in Atascadero CA

When I first started using hot hide glue I looked around the web to see what others were using and saw that the Rival electric water kettle was a popular way to go. I had the mini crock pot on hand so I thought I would try it out just to see how I liked hot hide glue before committing to spending money on a traditional glue pot or some other substitute. I took to it like a fish to water and set out to find a better way of controlling the temp of the hot glue. The problem with the crock pot is the same as with the rival pot, there is no way to control the heat. This is also an issue with the commercial hide glue pot except that they are designed to heat to 140*. My impression of why the rival pot is so popular is that it is cheap and it is a nice size. My set up is about the same size and is made out of metal with a ceramic liner rather than mostly plastic with a metal bottom/heating element. My little crock pot will heat water to 180+ and allow me to use it just like others use the Rival unit. However because the pot on mine is thick ceramic and distributes the heat evenly I can place the glue directly in the crock pot and not scorch the bottom. Frankly I don't understand why the mini crock pots aren’t what others are using.

I started using hot hide glue in the late spring when we had a few cold days but it soon started hitting some summer like temps. This coupled with some different types of joints and I quickly knew I wanted some way to be able to play with the temps to suit what I needed to do. The dimmer switch gave me enough control that I knew that was the right direction so that’s when I started looking for a variac.

One of my favorite aspects of using hot hide glue is the brush. A squeeze bottle is marginally helpful for getting the glue on a surface but I was always looking for a brush to spread it around a joint. With hot hide glue I have been using the same glue brushes for 5 years. If I forget to wash it out I just pop in the glue pot and in 30 min it’s as good as new and ready to use, try that with yellow glue.

I am very happy with how my set up works what I was hoping for was a bit more discussion of the appropriateness of putting the whole crock pot in the freezer. Should I let the glue defrost before plugging it in, crank the variac up to 100% till the glue begins to melt, use a refrigerator in the house rather than the freezer in my shop, or transfer the glue to another container before popping it in the freezer?

Robin

Re: Hot hide glue mishap

#9

Re: Hot hide glue mishap

kellyanderson72

The Rival pot has an adjustable dial for heat control, 2 dots up is right about 140. Just set it and forget it, heats perfectly every time and only cost $10.00.