New WoodChat!
Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Reach the woodworkers who ACTUALLY BUY

While on the subject of drawers....

Posts

While on the subject of drawers....

#1

While on the subject of drawers....

roger lance

two questions....first, we discussed ways to align an inset drawer flush with the cabinet with various drawer stops....but how do you prevent a drawer from being accidentally pulled completely out of the case ?? what do you use to stop the drawer from this ??....second, if the drawer front will be finished with dye/glaze, how do you finish the front and not get any stain on the other drawer parts and especially how do you finish the end of the pins and get that great contrast between pins and drawer sides ??....do you finish the front separately after the dry fit and then glue up ??

Re: While on the subject of drawers....

#2

Blue Tape

Todd Nebel

I've not done anything to prevent your first question from happening. For your second question I've used blue tape. I've masked off enough to keep the sides and bottom from getting any stain/dye. I've also used an exacto knife to allow the pins to be stained but not the tails or drawer sides. Lastly I used tape to allow only the pins and tails to receive stain, but not the rest of the sides. The baseline helps keep any dye bleed back from getting under the tape. For me it depends on what I'm trying to achieve with the piece (show or daily user) and the contrast or lack of contrast between the primary and secondary woods.

Re: While on the subject of drawers....

#3

Drawer stops

Kenneth Martin Sacramento

One way to stop a drawer is to fasten a block on the back of the drawer so that it hits the top of the opening.

Since most people stop pulling on a drawer when they see the back another way is to make the sides longer than the drawer. Then when the back reaches the opening there are several inches of the side still inside.

Re: While on the subject of drawers....

#4

Re: Drawer stops

Tony - Memphis

I put block on mine that pivot on a screw. To remove the drwaer, you have to reach in and rotate the block out of the way.

Tony

Re: While on the subject of drawers....

#5

Re: Drawer stops

Pam Niedermayer

I really like the way my refrigerator drawers work vis a vis stops (about the only thing I do like on this abomination called Maytag). There's a rounded ridge on both drawer and runner, so you lift the drawer a tad to get it over the ridge and out. Very cool, and not that difficult to replicate in wood. I haven't tried this yet, but will on the next drawers needed.

Pam

Re: While on the subject of drawers....

#6

Re: Drawer stops

GolfSteve in Calgary

Like Tony, I've used block on mine that pivot on a screw. To remove the drwaer, you have to reach in and rotate the block out of the way. Pictures here: http://www3.telus.net/steve_n_shelly/WW_files/WW_proj1_grannytbl.html

On a small drawer I embedded magnets in the drawer side and into the drawer carcasse. This works very well, but the magnets are too strong for a small drawer. I've been wanting to try this on a larger drawer.


Re: While on the subject of drawers....

#7

Can you sketch the Maytag solution?


Re: While on the subject of drawers....

#8

The elegant approach

Bill Tindall

I have been unable to get a picture but it is the same technique used to secure the center document assembly in a Period slant top desk. I will try to describe.

A dado in made perpendicular to the drawer divider above the drawer to be stopped . In this dado is fitted a thin flexible (hickory is traditional) strip that angles down to just engage the back of the drawer. To remove the drawer this flexible strip is lifted.

Drawer stops are particularly efficacious on shallow drawers. I faced this problem and forgot to dado the divider before assembly. I came up with this inelegant solution. The top divider was drilled and counter drilled to accommodate this pin which drops down to catch the back of the drawer.



Re: While on the subject of drawers....

#9

Re: While on the subject of drawers....

roger lance

I know of a couple ways of stopping the accidental removal of a drawer both of which are defeated by the reduction of the width of the drawer back (see Derek, Ian, & Andrews traditional drawer backs)....I was hoping to see what they do to stop a drawer....that is elegant Bill, have to remember that....I guess masking off the drawer is the only method for finishing the drawer front....anyone tried finishing the front separately before glue up??

Re: While on the subject of drawers....

#10

Still elegant

Bill Houghton, Sebastopol, CA

I would say that solution is just differently elegant, Bill. Far better than the other solution I've seen reference to, which uses a rectangular button that, with its long side parallel to the back of the drawer, stops it; but turned 90 degrees, slips through a notch cut in the back.

Re: While on the subject of drawers....

#11

Can't prefinish....

Bill Tindall

Unless you are a better drawer maker than I. It could not be planed to fit if prefinished. Well, it could but the finish would be compromised.

Re: While on the subject of drawers....

#12

Maybe can at least partially pre-finish

roger lance

Bill....I know it is the sides of the drawer that may need planing after glue up and there goes the finish on the pin ends....but the inside of the drawer front could be finished....and the front of the drawer could be finished....and the top and bottom of the drawer front could be finished as well without worry of having to plane those surfaces....but to be able to plane the sides at the dry fit??....hard to get around that!!

Re: While on the subject of drawers....

#13

staining drawer fronts

Bill Tindall

I would stain the top edge but never the inside, bottom or ends.

Re: While on the subject of drawers....

#14

Re: Can you sketch the Maytag solution?

Pam Niedermayer

I'll take a couple of photos, see how that works for you.

Pam