New WoodChat!
Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

A55 Smoothing Plane

Shaker Table Design Question

Posts

Shaker Table Design Question

#1

Shaker Table Design Question

Todd Nebel

Hello All, I working on a hallway table in the Shaker style. This style is from a picture I have in a book on Shakers. The text in the book says there's two drawers, one on each side. But the text doesn't provide any other information and the picture shows only one side. I will be making both drawers the same length. So, how should I design the drawer stops to keep the backs from hitting each other? I was thinking of adding a 1/4" by 1/4" groove in the middle of each of the drawers tracks and gluing in a small block of wood. Then each drawer's back will register against the block. I'm open to other ideas or a period correct solution whatever that would be. Here's a picture of the progress dry fitted together.

Thanks, Todd


img

Re: Shaker Table Design Question

#2

easy fix

Bill Tindall

A common way I see on both English and American Period furniture is to put a block of wood about an eighth inch high on the drawer blade to stop the drawer at the inside bottom edge below the drawer bottom. Alignment is easy when done before the bottom is installed. Just position the drawer, rub joint the block and let it dry. I often add two tiny brads for insurance but rub joints don't fail, what ever the glue used.

Re: Shaker Table Design Question

#3

Re: Shaker Table Design Question

roger lance

Todd....beautiful wood figure !....should be a stunner!....the way you suggested will work....if you are building the drawers with a reduced back width that allows the drawer bottom to screw into the back for support, then Christian Becksvort's method of mortising a couple of small blocks into the drawer divider so that the back of the drawer front hits them when the drawer is closed and flush also works. Clear as mud ??

Re: Shaker Table Design Question

#4

PS

Bill Tindall

What framing is going on top of the drawer to keep it from tipping down when withdrawn? You could just nail a runner on each side. That would be period authentic.

Dang what wood! We sold lumber for nearly thirty years and I never got a board like that in a shipment. Where do you find such curly stuff?

Re: Shaker Table Design Question

#5

Re: PS

Todd Nebel

Hi Bill, yes there's going to be drawer runners above the drawers to keep them from tipping out, just haven't gotten there yet. I bought this at Fleetwood Lumber in Pennsylvania. They are about 15 miles from me. Let's just say it's not cheap, but the wood makes the furniture (and distracts from my mistakes).

Re: Shaker Table Design Question

#6

Re: Shaker Table Design Question

Todd Nebel

Hi Roger, no that's clear. I did that on a piece this past winter. Definitely still an option. Thanks.

Re: Shaker Table Design Question

#7

Re: Shaker Table Design Question

kellyanderson72

how about one long drawer that pulls out from each side?

Re: Shaker Table Design Question

#8

Is that period authentic?

Todd Nebel

I thought about that but the text does say two drawers. I know the Shakers did that on small candle tables, but side tables too?

Re: Shaker Table Design Question

#9

Re: Shaker Table Design Question

Warren in Lancaster, PA

I can't remember seeing Shaker drawer stops discussed and the only Shaker piece I have worked on was a spinning wheel. Bill gives a good period technique, but I doubt you would see any kind of mortise or slot for the stop; that's more like 20th century.

I think I would glue a block of wood (like 1/2 x 1/2 x 1) on each side onto the runner, another period technique. After it is dry you can make small adjustments by paring the blocks or you could have the drawer bottom protrude a little in the back so you could plane it to fit on both sides. You ought to consider having the drawers of different lengths. This would be quite typical of Shaker design, something like 8 inches long and 15 inches long. You would still have the same amount of space, but could accommodate larger items in one drawer.

Re: Shaker Table Design Question

#10

correction

Bill Tindall


The stop blocks are more like 3/16 thick. The use of 2 on this small drawer was overkill. The compelling advantage is that there is no measuring involved as to where they are positioned. I am fond of techniques where there is no chance to screw up.

Re: Shaker Table Design Question

#11

Those techniques...

John in NM

Where one can't screw up....

I like them too, but you'd be amazed at my innovation when it comes to finding new and novel ways to screw up :D

Re: Shaker Table Design Question

#12

Re: correction

Todd Nebel

Thanks for the picture Bill. My drawers will be small and not used much so gluing in a small block in the front can work.

Re: Shaker Table Design Question

#13

Re: Shaker Table Design Question

Todd Nebel

Thanks Warren. I think I will make the drawers different lengths. The book I referenced mentioned that on another similar table with drawers.

Re: Shaker Table Design Question

#14

Re: correction

Bill Tindall

You will fine this stop on fine English or American furniture and on drawers of any size. There is nothing shabby or frail about it.

Re: Shaker Table Design Question

#15

Build one double ended drawer?

Ian (in Sydney, Australia)

Hi Todd

I'm not sure if it would be authentic Shaker, but you could just build a single double ended drawer.

If you did, making the drawer 1/16 to 1/8in shorter than the box is long would be appropriate. A drawer that closes to just inside it's frame is considered proper construction in some circles.